Loewe L 37, L 42 Programming recording for recorders, EPG menu, Selecting providers and stations

Page 28

Operating modes – EPG

In front of the programme’s title, the system places an ۪. This station is switched later to this programme when the set is switched on. If the TV is off, it switches on again automatically at the beginning of the marked programme if this has been set in the EPG menu. If you are out, a security prompt prevents the TV set staying on unattended.

Before leaving the upper selection lines using the blue coloured key, select a specific line. If you have switched back to the programme list, you can change this

menu line using

without having to leave the programme list.

Programming recording for recorders

The programme marked using the

buttons can be prepared for recording by

pressing the red coloured key. In the following menu, confirm the timer data or change them as required. Then a red dot is set in front of this programme in the EPG programme list as an identification (if timer data is being transferred to the recorder, no red dot is set). If you select this programme, you can delete it from the timer using the red coloured key (if the timer data has been transferred to a recorder, the timer has to be deleted there).

EPG menu

Call EPG menu

 

EPG menu

INFO

END

 

 

Select provider OK

Station select Timer list Data capture

Switch

 

 

 

 

 

 

You will find the following settings in the EPG menu:

• Select provider • Station selection • Timer list • Data capture

• Switch on TV when marked

Selecting providers and stations

If you want to change the provider for analogue TV reception (the station which transmits EPG data) to have other stations evaluated, you can do this under “Select provider“.

Select “Select provider“ and call this menu using OK. If the station you want to switch to is not listed in the “Select provider“ list, then use the yellow coloured key to start the automatic search for stations with EPG data. This takes a while. Or, if you know the station that transmits EPG data, press the blue coloured key to compile manually. Select the provider in the station list and adopt it by using OK and return to the provider selection using .

Select the provider in “Select provider“ and adopt it using OK. Then a station list search is performed. The stations offered by the provider are displayed in a list.

First, all stations are marked with the ۪ symbol so that their data is display- ed in the programme guide (precondition: provided EPG data is broadcast for the respective station). Stations indicated by ۬ are analogue terrestrial/cable stations, stations indicated by ۼ are DVB-T stations, stations indicated by ۽ are DVB-C stations and stations indicated by ۻ are DVB-S stations. These stations are available for evaluation in the programme guide.

Select the stations you want to omit from the programme guide one after another and deactivate each one by using OK. The ۪ symbol is removed.

Data capture

After these settings or after each time the set is switched off using the mains switch, the data must first be collected, before switching on the set.

To do this, select the station you have defined as a provider and leave the TV set switched on for about one hour or switch the set to the standby mode. After about two minutes in standby mode, the indicator on the set turns orange. The data acquisition begins and lasts about 1 hour. When data acquisition is termi- nated, the indicator turns red again. The data are also automatically captured between 2 a.m. and 5 a.m. when the TV is switched to standby.

A prerequisite for data capture is that “Data capture“ is “on“ (for DVB + analogue) in the EPG menu.

Note: If the TV set is switched off using the mains switch or the mains plug is pulled out, all EPG data are lost.

If, for example, you cannot receive any analogue EPG providers or if you only use DVB, you should set the data capture to “on (only for DVB)“.

Switch on TV when marked

You can have the TV switched on automatically from standby at the beginning of the marked programme. If you are not present at the time, a safety prompt makes sure the TV switches off again after 5 minutes.

- 28

Image 28
Contents Operating Instructions Contents Remote control TV functions Direct recordingDigital Recorder +/PControl unit Connections to rear panel Xelos a Connections to rear panel Xelos a 32/37 and Modus L 32/37 Connections to rear panel Xelos a 42 and Modus L Welcome Cleaning DisposalPacking and box SetFor your safety Heating from radiatorsRemote control First installationConnection Using the conditional access module Switching onUse of the binders for Xelos A42 and Modus L Side of the moduleSettings can be selected by pressing one of the directions Automatic programmingColoured key Station sortingSwitching on/off Directing DVB-T antennaDaily operation Changing stationsBasics about the Menu operation Example of the menu operationCall the TV menu Select Settings Info text indicates which settings you can make in StationsFor the info system Select Stations in the line belowThis is how to select the index item Use the OK button to call Switch off AutomaticFor the index Use P+/P- to scroll up or down through the pagesPicture settings Setting the soundDirect control on TV set How the coloured keys work in TV mode Operating modes TVShow status display Calling the indexCall timer overview Under Settings you will find the following functionsCalling additional functions Select picture formatDVB subtitles Installing new DVB software Removing the CA moduleInserting a new CA module Searching for new softwareImage+ Image+ demo modeImage+ menu Operating modes PIP Picture in picture PIPSwitch to split screen Setting the PIP typeSwitch to small PIP Functions in the PIP menuUsing the EPG Switch EPG on/offOperating modes EPG EPG Programme guideSwitch on TV when marked Programming recording for recordersEPG menu Selecting providers and stationsOperating modes Teletext Analogue TeletextProgramme timer recordings Teletext menuDisplay teletext menu Programme wizard for recording via teletextOperating modes Radio RadioRadio menu Call radio menuLogin and connect equipment Connecting video/DVD recordersOperating additional equipment Start search with the blue coloured keyTimer recording with video or DVD recorder Video playbackCalling AV inputs in the AV selection Call AV selection Calling AV input via the station listAudio input Audio Digital Assignment of digital audio inputs and outputsAudio output Audio Digital OUT Loewe Flat-TV Connecting other audio amplifiers or active speakers Setting colour standard Hdmi DVI connectionVGA/XGA connection Set geometry as described for VGA/XGA connectionSound from PC or Set Top Box Component video connectionLog in the component/device in the connection wizard Use the remote control to operate one of the DVD players Use the remote control to operate a recorderReturn to using the remote for the TV Set remote controlProblem Possible cause Remedy What to do, ifDigital Link Plus does not function Replace the Euro-AV cableDts, Mpeg ConnectedTechnical data General dataType Modus L Type Xelos aElectrical data ConnectionsAccessories Retrofitting options Item no. version PIP-Tuner DigitalService Center Loewe Service addressesPlac Kaszubski