Panasonic NV-VP31 manual Tuning the TV to Your Unit, Press Menu, Press VHS Í to turn on this unit

Tuning the TV to Your Unit

The unit supplies a signal to the TV via the RF coaxial cable on channel AU28s 69 or NZ21s 69. It is possible to view the unit’s picture on your TV in the same way that you watch TV broadcasts. The unit is fitted with its own tuner (just like a normal TV) and can be preset to receive up to 99 TV broadcast stations. ≥Switch [VHS/TV/DVD] to “VHS”.

¬If you have connected the unit to the TV through the audio/video output sockets

You do not need to follow the procedure below. To view the pictures from the unit, set to the AV mode on the TV with [AV].

Pre-programmed TV Channels (for NV-VP31GL/Australia)

VHS/DVD/TV

VHS/DVD	TV	TV	VHS/
VHS	VHS	DVD
			TV/
VHS/DVD	QUICK REPLAY DUBBING	REC	DVD

The local TV broadcast channels 2, 7, 9, 10 and 28 are factory-preset in the unit.

That is, if you can receive TV broadcasts on VHF channels 2, 7, 9, 10 and UHF channel 28, these are already tuned on the programme positions with the matching numbers.

	OUTPUT
			TRACKING/V-LOCK
	1	2	3	CH
Numeric			CH
	4	5	6
buttons
			VOLUME
	7	8	9

AV AV 0 -/- -

INDEX/SKIP SLOW/SEARCH

[1]Press [VHSÍ] to turn on this unit.

[2]Hold down [MENU] for 5 seconds or more.

[3]Set the TV to an unused position for the unit

viewing channel.

≥Tune the TV until the display shown on the right appears. Refer also to the TV’s instructions regarding tuning.

Panasonic

END: MENU

Getting Started

NAVI		MENU
TOP MENU
DIRECT		PLAY
NAVIGATOR		LIST
ENTER
DISPLAY		RETURN
PROG/CHECK TIMER	PROG PLAY	JET REW

[4]Press [MENU].

MENU

Plug in Auto Tuning (for NV-HV60GN/New Zealand)

When the unit is turned on after connecting the aerial cable and the mains lead for the first time, tuning starts automatically.

≥If the unit is turned on with the aerial not connected, all channels are skipped.

			AUTO TUNING
[1]	Press [VHSÍ] to turn on this unit.		IN PROGRESS,
			PLEASE WAIT.
[2]	Set the TV to an unused position for the unit	CH 22	SEARCH	21
			END: MENU
	viewing channel.

		≥Tune the TV until the display shown on the right appears. Refer also to
		the TV’s instructions regarding tuning.	AUTO TUNING IS
		[3] Press [MENU].
			COMPLETED.
			END: MENU
		¬ To cancel Auto Tuning partway through
	CH	Press [MENU]. Auto Tuning will stop halfway by turning the unit off, pressing [MENU], playback or a
		power failure.
		¬ If Auto Tuning stops halfway by turning the unit off, playback or a power failure
/I
		≥Disconnect the mains lead and then reconnect it.
EJECT		≥Turn on the unit. Plug in Auto Tuning restarts.

TIMER REC	TAPE REFRESH	CH	REC/OTR	¬ To set the channels manually (lpage 23)
PULL-OPEN
			REW	FF
	VIDEO	L	AUDIO R	ªTo restart Plug in Auto Tuning
AV2 IN
				≥Turn the unit on.
				≥Make sure there is no video cassette in the unit.

1)	Keep both [CH] I and J on the unit pressed simultaneously for 3
	seconds or more until the channel on the unit’s display changes to 1.
2)	Disconnect the mains lead and then reconnect it.		1
3)	Turn on the unit. Plug in Auto Tuning restarts.	Disappears

To change the RF output channel

NV-VP31GL

28 … 69

(RF OFF)

NV-VP31GN

2169

(RF OFF)

You can change the RF output channel, for example, when interference occurs on the picture after tuning.

1)Hold down [MENU] for 5 seconds or more.

2)Press [CH]IJ to select the channel (AU28s69, NZ21s69).

≥Each time you press [CH]IJ (l left)

≥Set to “ss” (RF OFF) when you use the audio/video cable for the connection.

≥You can also use the numeric buttons. Example: “28”; [2]l[8]

3)Retune your TV to the new RF channel for the unit.

4)Press [MENU] to exit the setting mode.

Note:

≥Even if the RF output channel has been changed, it is not necessary to perform Auto Tuning.

NV-VP31GL

NV-VP31GN

Panasonic

END: MENU

11