LSQT0879.book 4 ページ ２００５年２月８日 火曜日 午後７時８分
Connections
This section shows you how to connect the VCR to an aerial, TV, etc.
Basic Connections
The following connections are required to record and play back the video cassette through the TV.
|
| (1) |
| (3) | (2) |
|
| (4) |
| AC IN ～ | IN |
| VIDEO |
|
(6) | AUDIO | OUT |
|
| |
| IN(AV1) OUT | RF |
| ¢ | (5) |
|
| |
(1) Aerial (Not supplied) | (6) AC Input socket (39) | |
(2) TV Set (Not supplied) | ¢ To mains supply | |
(3)Aerial Connector
(4)RF IN socket (42)
(5)RF OUT socket (45)
Connection to a TV using the Audio/Video Input Socket:
Set the RF output channel of the VCR to [ss] (RF OFF) when the VCR is connected to the TV via the Audio/Video cable. (See to the right.)
|
|
|
| (1) |
|
| (3) | (2) |
|
|
| (4) | (5) | (7) |
|
|
| (6) | |
| AC IN ～ |
| IN |
|
|
| VIDEO |
|
|
| (10) | AUDIO | OUT |
|
|
|
|
| |
|
| IN(AV1) OUT | RF |
|
|
| (9) |
| (8) |
| ¢ |
|
| |
|
|
|
| |
(1) | Aerial (Not supplied) | (8) RF OUT socket (45) |
| |
(2) | TV Set (Not supplied) | (9) VIDEO OUT (41)/ |
| |
(3) | Aerial Connector |
| AUDIO OUT (44) |
|
(4) | VIDEO IN |
| (10)AC Input socket (39) |
|
(5) | AUDIO IN |
| ¢ To mains supply |
|
(6)Audio Cable/Video Cable (Not supplied)
(7)RF IN socket (42)
4
Tuning the TV to Your VCR
The VCR supplies a signal to the TV via the RF coaxial cable on channel
If you have connected the VCR to the TV through the Audio/ Video input sockets, then you do not need to follow the procedure below. To view the pictures from the VCR, set to the AV mode on the TV with [AV] (2).
Preparation
•Turn on the TV and the VCR.
Operations
1 Hold down [MENU] (9) for 5 seconds or more.
2Set the TV to an unused position which you wish to use for your video playback.
•Tune the TV until the display shown below appears on the screen. (Please refer to the TV manufacturers operating instructions regarding tuning.)
Panasonic VCR
END: MENU
3 Press [MENU] (9).
To Change the RF output Channel
You can change the RF output channel, for example, when interference occurs on the picture after tuning.
Operations
1Hold down [MENU] (9) for 5 seconds or more.
•The VCR display changes as shown below and the VCR picture on the TV displays this pattern.
Panasonic VCR
Example for Australia
END: MENU
Example for New Zealand
2Enter the desired channel number
•Set the RF output channel of the VCR to [ss] (RF OFF) when the VCR is connected to the TV via the Audio/Video cable.
•Press [CH] (20) to display [ss].
For New Zealand | For Australia |
… | |
| (Initial position) |
ss
(RF OFF)
•It is also possible to select by pressing [Numeric] (3).
Example: 28: 2 
8
3Press [MENU] (9) to finish the setting mode.
4Retune your TV to the new RF channel for the VCR.
Note:
•Even if the RF output channel has been changed, it is not necessary to perform Auto Tuning.
LSQT0879