Connections and Plug&Play Setting

ACheck contents

Make sure the package contains all of the accessories listed in “Specifications” ( pg. 21).

BSituate VCR

Place the VCR on a stable, horizontal surface.

CConnect VCR to TV

Antenna or cable

Coaxial cable

Flat feeder

Matching transformer (not supplied)

AC power cord

Back of VCR

AC outlet

	To audio/video	Audio/video
	input connectors	Audio/video
		cable
		(not supplied)
	To 75 terminal
	TV	RF cable
	TV	(supplied)
		(supplied)
	To S-video input	S-video cable
	connector	(supplied)

RF Connection

ADisconnect the TV antenna from the TV.

BConnect the TV antenna cable to the ANT. IN terminal on the rear of the VCR.

CConnect the supplied RF cable between the TV OUT terminal on the rear of the VCR and the TV’s antenna input terminal.

AV Connection

(improves picture quality during tape playback.)

If your TV is equipped with audio/video input connectors

AConnect the antenna, VCR and TV as shown in the illustration. B Connect an audio/video cable between the AUDIO/VIDEO

OUT connectors on the rear of the VCR and the audio/video input connectors on the TV.

S-video Connection

(allows you to make the most of the S-VHS picture performance.) If your TV is equipped with a S-video input connector

APerform “RF Connection” above.

BConnect a S-video cable between the S VIDEO OUT connector on the rear of the VCR and the S-video input connector on the TV.

CConnect an audio cable between the AUDIO OUT connectors on the rear of the VCR and the audio input connectors on the TV.

●Even if you are using audio/video cables to connect your VCR to your TV, you must also connect it using the RF cable. This will ensure that you can record one show while watching another.

DPerform Plug&Play setup

Plug the AC power cord into an AC outlet. Do not turn on the VCR. The clock and tuner channels will be set automatically. The time and date can be set automatically by the clock setting data transmitted from one of the regular TV broadcast channels. We call this TV channel the “host channel” and it is a PBS channel in your area.

ATTENTION:

●If you use a cable box, Plug&Play will not function; set the clock and tuner channels separately ( pg. 7 – 8).

●Depending on areas or reception conditions, the VCR may not receive the Auto clock setting data from the PBS channel. If this function is taking a considerable amount of time, it may be

necessary to perform the procedure in “Semiauto Clock Set” ( pg. 7) or “Manual Clock Set” ( pg. 8).

During Initial Auto Clock Set “Aut” blinks.

During Auto Channel Set

The channel numbers are displayed as they are scanned and set.

Plug&Play Completed

The current time is displayed.

What to do if Plug&Play setting failed

●If an incorrect time is displayed on the display panel, perform the procedure in “Semiauto Clock Set” ( pg. 7) or “Manual Clock Set” ( pg. 8).

●If “–:– –” appears on the display panel, ensure that the antenna cable is connected correctly. Then turn on and off the VCR; the Plug&Play setting will be automatically reactivated. If Plug&Play setting is not performed though the antenna cable is connected

correctly, perform the procedure in “Manual Clock Set” ( pg. 8) and “Auto Channel Set” ( pg. 8) or “Manual Channel Set” ( pg. 8).

ESet VCR channel

The VCR channel is the channel on which you can watch the picture from the VCR on the TV when only using the RF connection. Press POWER 1 to turn off the VCR, then press STOP/EJECT (0) on the VCR for more than 5 seconds. “CH3” appears on the display panel. Press CH+/– on the Remote to select “CH3”, “CH4” or “CH–”(OFF), then press OK.

●The VCR channel is preset to “CH3”. Set to “CH4” if CH3 is used for broadcasting in your area.

FFinal preparation for use

Turn on the VCR and the TV, and select the VCR channel 3 or 4 (or AV mode) on the TV. You can now perform basic playback or basic recording.

●If you connect the TV and the VCR only using the RF connection, press TV/VCR on the Remote so that the VCR mode indicator lights on the display panel.

— 6 —