Panasonic PV DM2092 manual Do steps 1 and 2 on, Audio Output, Repeatedly for output, See below

*Important: If a remote control button does not work when pressed, press the , DVD button on the remote and try the button again.

AUDIO OUTPUT

Select the digital output to be output from the optical digital audio output connector of the unit.

1 Do steps 1 and 2 on page 58.

	DVD MAIN MENU				1) Press	to select
	AUDIO OUTPUT				“AUDIO OUTPUT.”
	DISC LANGUAGES
	ST I L L MODE		: F I ELD		2) Press SET to
2 TV MODE			: L e t t e r b o x
	SELECT	:			display screen.
	SET	: SET
	END	: ACTION
	AUDIO OUTPUT				1) Press	to select
					an item.
	LPCM(DVD)		: OFF	t r e a m
	D o l b y D i g i t a l : B i t s
	d t s		: OFF		2) Press SET
	SURROUND		: OFF
3 DRC			: OFF
	SELECT	:			repeatedly for output.
					(See below.)
	END	: ACTION
	SET	: SET

■“LPCM (DVD)” selections

OFF: Linear PCM of less than 48 kHz/16 bit is output. When playing DVDs recorded in linear PCM of over 48 kHz/20 bit or 96 kHz, no digital audio is output. (Factory preset)

PCM: When playing DVDs recorded in linear PCM of 48 kHz/20 bit/24 bit or 96 kHz, digital audio converted to 48 kHz/16 bit is output.

(Digital output of PCM audio is restricted to

48 kHz/16 bit or below for copyright protection.)

■“Dolby Digital” selections

Bitstream:	Dolby Digital bitstream (1ch-5.1ch) is
OFF:	output. (Factory preset)
	No output.

■“dts” selections

Bitstream:	dts bitstream is output. (Factory preset)
OFF:	No output.

■“DRC (Dynamic Range Compression)” selections

OFF: Normal audio range is selected. (Factory preset)

ON: For dynamic sound even at low volume, this is useful for late-night listening. [Dolby Digital DVDs only].

■“SURROUND” selections

Surround Sound creates the effect of sound coming from non-existent rear speakers even when only connected to a 2-channel stereo system.

OFF: No Surround Sound effect. (Factory preset)

ON: Surround Sound effect.

4 Press ACTION to redisplay DVD menu and go to step 2 to setup another item. Or, press ACTION three times to exit.

Type of amplifier	Recommended setting
	LPCM		Dolby
to be connected				dts
	(DVD)		Digital
No amplifier is connected	OFF		OFF	OFF
AV amplifier (with digital
audio input connector)	PCM*1		OFF*2	OFF*2
without Dolby Digital/dts
decoder
AV amplifier including	PCM*1		Bitstream	OFF
Dolby Digital decoder
AV amplifier including		1	Bitstream	*3
Dolby Digital/dts decoder	PCM*			Bitstream

•Make settings according to amplifier connected to optical audio output as shown in above table.

•When a dts decoder is not connected, to enjoy dts DVD, please select audio output other than dts on the dts DVD menu screen. Otherwise, there will be no sound from the unit speakers.

*1 Audio output from unit is converted to 48 kHz/16 bit in addition to audio from digital audio output.

To enjoy high quality sound at 48 kHz/20 bit / 24 bit or 96 kHz, connect the amplifier or decoder directly to the audio output connectors, not to the digital audio output connector. [Select “OFF” at the “LPCM (DVD)”.]

*2 When connecting an amplifier (with an optical digital input connector) which does not contain the Dolby Digital or dts decoder, be sure to select “OFF”.

If “Bitstream” is selected, starting DVD play may cause such a high level of noise as to be harmful to your ears and damage the speakers.

*3 When a dts decoder is connected, please select “Bitstream” in “dts”. If “OFF” is selected, there will be no sound.

Notes	For
• Turn off other surround effects when	Your
using this surround effect.
• For optimum effect, the distance between
the unit and the listener should be about	Information

3 or 4 times the distance between the right and left front speakers.

59