Multiquip V304 manual Gasoline Check, Water Tank

Page 21

Explosive Fuel

Gasoline Check

1.Remove the gasoline cap located on top of fuel tank.

2.Handle Fuel in a safety container. If the container does not have a spout use a funnel.

3.Visually inspect to see if fuel level is low. If fuel is low, replenishwithunleadedfuel.Whenrefueling,besuretouse a strainer for filtration. DO NOT top-off fuel. Wipe up any spilled fuel.

4.Pay attention to the fuel tank capacity when replenishing fuel. Refer to the fuel tank capacity listed on page 11, Engine Specification Table 1.

V304 — INSPECTION

Water Tank

1.Fill the water tank (Figure 13) with clean water, and verify that valve for the water tank is closed.

Figure 13.Water Tank Filler Port

Hydraulic Pump Fluid

1.Visually inspect the hydraulic fluid in the hydraulic reservoir (Figure 14). If the hydraulic fluid is low, fill the reservoir with Mobil 300, GM Dextron B or Ford MZC-41A type hydraulic transmission fluid to the correct level.The correct hydraulic fluid level will be indicated on the reservoir.

Figure 12. Fuel Tank Filler Port

Figure 14. Hydraulic Reservoir Filler Port

V304 VIBRATORY ROLLER — OPERATION AND PARTS MANUAL — REV. #8 (11/13/09) — PAGE 21

Image 21
Contents Model Proposition 65WARNING Page Table of Contents Parts Ordering Procedures Best Deal! Order via Internet Dealers OnlyOrder via Fax Dealers Only V304 Safety Message Alert Symbols V304 Safety Message Alert Symbols Rules for Safe Operation General SafetyRules for Safe Operation Machine Safety Decals Operation and Safety DecalsEngine Specifications V304 Specifications30-4 Roller Dimensions Side View V304 DimensionsV304 Roller Dimensions Front View Roller Components V304 Roller ComponentsV304 Roller Components V304 Roller Components Initial Servicing V304 Engine ComponentsV304 General Information Operating on Slopes Tipping RolloversBefore Starting V304 InspectionEngine Oil Check FuelWater Tank Gasoline CheckGearbox Lubrication Vibratory and Travel V-Belt TensionClogged Drive Belt Tension Handle Positions Initial Start-up Instructions Handle Bar AdjustmentThrottle Lever V304 Initial START-UPV304 Operation OperationFree Wheel Engagement Lever Vibratory Control Lever on Shut-Down Vibratory ControlV304 Maintenance Adjusting Control Rods Travel Control Rod Adjusting or Changing Vibratory V-BeltClutch and Engine Coupling Lubrication Points Zerk Fittings Clutch and Engine coupling LubricationRoller Storage V304 Preparation for Long -TERM StorageV304 Troubleshooting Roller Engine Troubleshooting V304 Troubleshooting EngineV304 Troubleshooting Engine Explanation of Code in Remarks Column To 3 Units V304 Suggested Spare PartsV304 Name Plate and Decals Decal Safety Chain Decal Safety InstructionsDecal Water Valve Decal Vibration ON/OFFV304 Cocoa MAT Assy PLATE, Front Scraper V304 Cocoa MAT Assy15 5 V304 Travel Linkage AssyPart Name V304 Vibratory Linkage Assy V304 Vibratory Linkage Assy V304 Handle Assy Cable ASSY. Kill Switch SWITCH, KillCable ASSY. Engine ScrewV304 Chassis Assy Part Name QTY Remarks V304 Transport Hooks Assy CARRYING, Hanger HOOK, HangerBRACKET, Strut WASHER, Lock 3/4V304 Pump Drive Assy WASHER, Flat Pulley WASHER, Lock 1/4PULLEY, Travel KEY, Woodruff 1/8 X 1/2 TBD ScrewVibratory Drive Assy V304 Vibratory Drive AssyClutch Assy SET Screw WASHER, Flat 1/4RING, Snap PULLEY, Drive BeltV304 Vibratory Roll Assy Part Name QTY V304 Battery Assy CABLE, Negative Battery BASE, Battery MountingBattery CABLE, Positive BatteryV304 Spray Assy Connector ELBOW, ConnectorFILTER, Y-CONNECTOR BAR AssyV304 Transmission Assy Transmission Cover BOX Transmission Base BOXSpiral PIN Special CAP ScrewPayment Terms Special Expediting ServiceFreight Policy Minimum OrderPage Canada HERE’S HOW to GET Help