Furuno MU-17OC manual Specifications of MULTI-PURPOSE LCD Display, MU-170C

Page 28

FURUNO

MU-170C

SPECIFICATIONS OF MULTI-PURPOSE LCD DISPLAY

MU-170C

1

GENERAL

 

1.1

Display

17-inch SXGA color TFT-LCD, 338 x 270 mm

1.2

Brightness

maximum: 1000 cd/m2 , minimum: 2 cd/m2 or less

1.3

Resolution

1280 x 1024 (SXGA)

1.4

Viewing Angle

up/down: 75°, left/right: 80°

1.5Input Signal

 

RGB ports

2 ports, VESA (VGA, SVGA, XGA, SXGA),

 

 

(0.7 Vp-p, Synchronization: TTL level)

 

DVI port

1 port, VESA (VGA, SVGA, XGA, SXGA)

 

VIDEO ports

3 ports, NTSC/PAL, 0.7 Vp-p (75 Ω)

2

POWER SUPPLY

 

 

 

12-24 VDC: 6.0-3.0 A

3 ENVIRONMENTAL CONDITION

3.1Ambient Temperature

Display Unit

-15°C to +55°C

Remote Controller

+5°C to +35°C

3.2 Relative Humidity

93% at +40°C

3.3Waterproofing (IEC60529)

 

Display Unit

Front panel: IP56, CFR46, Rear panel: IP20

 

Remote Controller

IPX0

3.4

Vibration

2-5 Hz and up to 13.2 Hz with an excursion of ±1 mm ±10 %

 

(IEC 60945 ed.4)

(7 m/s2 maximum acceleration at 13.2 Hz)

 

 

13.2-100 Hz with a constant maximum acceleration of 7 m/s2

4

COATING COLOR

 

 

 

N3.0 (Not changed)

SP - 1

E2034S01B

Image 28
Contents MU-170C Important Notice Safety Instructions Table of Contents Features ForewordWord to the Owner of the MU-170C IiiEquipment Resolution Signal System ConfigurationConnectable equipment Equipment Lists Standard supplyOption Name Type Code No Qty RemarksMounting Display UnitFlush mounting Flush mountingDesktop mounting Contents of bracket kitName Qty Remote Controller Setting batteryRemote controller RMC-200 Writing the device name on the labelWiring Display unit bottom viewGrounding Port, cable and connectable equipmentPort Used cable NameAdjustments RGB/DVI SettingRGB1 RGB2 setting menu DVI setting menu5500K/6500K/7000K/8000K Menu item FunctionAvailable range Video Setting VIDEO1 2 or 3 setting menuPicture-in-picture window Menu item Function Available rangeMenu Window Setting Adjusting the menu windowOSD menu OFF BlueChanging the signal name Signal name areaRemote Controller Setting System menuPower key OperationControls Display unitRemote controller Adjusting Display Brilliance Brill adjustment windowChoosing Source for Main Picture Disp selection windowChoosing Source for Picture-in-Picture PIP selection windowMAINTENANCE, Troubleshooting MaintenanceRoutine maintenance Do not open the equipmentTroubleshooting Fuse replacementBattery replacement LCD replacementClearing the Memory Specifications of MULTI-PURPOSE LCD Display MU-170CEC Declaration of Conformity MU-170C 000-012-653RMC-200 000-149-069付属品表 Spare Parts List for Page Page 魚群探知機 ソナー 17 型カラーLCD 表示器 MU-170C 仕 様 .総合.電源 .環境条件オールクリア キーを押して、resetを選びます。 工場出荷設定にリセットされます。 MENUキーを押して、メニューを閉じます。キーを押して、YESを選びます。 故障かなと思ったら 寿命がくると、輝度が十分に上がらなくなります。LCD の寿命時間は、約 40000 時間です。保守点検 ふだんの保守点検PIP ウィンドウの選択 PIP ウィンドウに表示させる入力信号を選びます。入力信号の選択 入力信号ウィンドウ またはキーを押して、入力信号を選びます。 DISPキーを連続的に押しても選ぶことができます。RGB1~ RGB2 ポートからの信号を表示する。 DVI ポートからの信号を表示する。輝度の調整 キーの名称 リモコンのキー説明PIP ウィンドウについては 3.2 節を参照 取扱い 操作キーリモコンの設定 表示器の ID リモコンの ID2 信号名の変更 メニュー表示の設定 1 メニューの調整設定項目の内容 設定範囲 VIDEO1、VIDEO2、VIDEO3 信号の設定 項目に応じたメニューが現れます。VIDEO1~VIDEO3は同じメニュー内容です。水平方向のドット調整 入力信号による 画面の横幅 狭まる(数値小)←→広がる(数値大) 装備後の設定 本機に接続している機器に応じて、信号の設定を行います。ポート、ケーブル、対応機種 ポート名 使用するケーブル コード番号 オプション Page リモコンの裏蓋を開けて、支給の電池(2 個)を入れます。 裏蓋を閉めます。 リモコン「RGB1」~「VIDEO3」に接続する装置名を貼りマークに記入し、リモコンに貼り付けてください。 卓上装備 卓上装備には、オプションのモニター用ハンガー1 式(型名 MU-170C用ハンガー, コード番号埋込み装備 取付け要領 表示器構成表 システム構成 対応機種 接続可能機種 解像度 信号形式はじめに 本機の特徴取付け要領 Page 安全にお使いいただくために 必ずお守りください「このページは空白です。」 重要なお知らせ