Furuno MU-17OC manual Safety Instructions

Page 3

SAFETY INSTRUCTIONS

Safety Instructions for the Operator

 

Safety Instructions for the Installer

WARNING

Do not open the equipment.

Only qualified personnel should work inside

the equipment.

Do not disassemble or modify the equipment.

Fire, electrical shock or serious injury can result.

Use the proper fuse and power cable.

Fuse rating is shown on the equipment. Use of a wrong fuse can result in damage to the equipment.

Immediately turn off the power at the switchboard if the equipment is emitting smoke or fire.

Continued use of the equipment can cause fire or electrical shock. Contact a FURUNO agent for service.

Do not place any object near the exhaust or intake vent.

Fire may result.

CAUTION

Do not connect/disconnect the signal cable while turning the power on.

The unit may be damaged.

A warning label is attached to the equipment. Do not remove the label. If the label is missing or damaged, contact a FURUNO agent or dealer.

WARNING

Name: Warning Label (1)

Type: 86-003-1011-1

To avoid electrical shock, do not

remove cover. No user-serviceable

Code No.: 100-236-231

parts inside.

 

WARNING

Do not open the cover unless totally familiar with electrical circuits and service manual.

Improper handling can result in electrical shock.

Turn off the power at the switchboard before beginning the installation.

Fire or electrical shock can result if the power is left on.

Do not install the equipment where it may get wet from rain or water splash.

Water in the equipment can result in fire, electrical shock or damage to the equipment.

CAUTION

Observe the following compass safe distances to prevent interference to a magnetic compass:

 

Standard

Steering

 

compass

compass

 

 

 

LCD Monitor MU-170C

0.5 m

0.3 m

 

 

 

Remote Controller

0.3 m

0.3 m

RMC-200

 

 

When lifting the display unit, hold it together with the hard cover.

Grasping by the hard cover alone may allow the display unit to fall, resulting in possible bodily injury or damage to the equipment.

i

Image 3
Contents MU-170C Important Notice Safety Instructions Table of Contents Iii FeaturesForeword Word to the Owner of the MU-170CSystem Configuration Equipment Resolution SignalConnectable equipment Name Type Code No Qty Remarks Equipment ListsStandard supply OptionDisplay Unit MountingFlush mounting Flush mountingContents of bracket kit Desktop mountingName Qty Writing the device name on the label Remote ControllerSetting battery Remote controller RMC-200Display unit bottom view WiringName GroundingPort, cable and connectable equipment Port Used cableDVI setting menu AdjustmentsRGB/DVI Setting RGB1 RGB2 setting menuMenu item Function 5500K/6500K/7000K/8000KAvailable range Menu item Function Available range Video SettingVIDEO1 2 or 3 setting menu Picture-in-picture windowOFF Blue Menu Window SettingAdjusting the menu window OSD menuSignal name area Changing the signal nameSystem menu Remote Controller SettingDisplay unit Power keyOperation ControlsRemote controller Brill adjustment window Adjusting Display BrillianceDisp selection window Choosing Source for Main PicturePIP selection window Choosing Source for Picture-in-PictureDo not open the equipment MAINTENANCE, TroubleshootingMaintenance Routine maintenanceLCD replacement TroubleshootingFuse replacement Battery replacementClearing the Memory MU-170C Specifications of MULTI-PURPOSE LCD DisplayEC Declaration of Conformity 000-149-069 MU-170C000-012-653 RMC-200付属品表 Spare Parts List for Page Page 魚群探知機 ソナー .環境条件 17 型カラーLCD 表示器 MU-170C 仕 様.総合 .電源キーを押して、resetを選びます。 工場出荷設定にリセットされます。 MENUキーを押して、メニューを閉じます。 オールクリアキーを押して、YESを選びます。 寿命がくると、輝度が十分に上がらなくなります。LCD の寿命時間は、約 40000 時間です。 故障かなと思ったらふだんの保守点検 保守点検PIP ウィンドウに表示させる入力信号を選びます。 PIP ウィンドウの選択DVI ポートからの信号を表示する。 入力信号の選択入力信号ウィンドウ またはキーを押して、入力信号を選びます。 DISPキーを連続的に押しても選ぶことができます。 RGB1~ RGB2 ポートからの信号を表示する。輝度の調整 リモコンのキー説明 キーの名称PIP ウィンドウについては 3.2 節を参照 操作キー 取扱い表示器の ID リモコンの ID リモコンの設定2 信号名の変更 1 メニューの調整 メニュー表示の設定設定項目の内容 設定範囲 項目に応じたメニューが現れます。VIDEO1~VIDEO3は同じメニュー内容です。 VIDEO1、VIDEO2、VIDEO3 信号の設定水平方向のドット調整 入力信号による 画面の横幅 狭まる(数値小)←→広がる(数値大) 本機に接続している機器に応じて、信号の設定を行います。 装備後の設定ポート、ケーブル、対応機種 ポート名 使用するケーブル コード番号 オプション Page リモコン リモコンの裏蓋を開けて、支給の電池(2 個)を入れます。 裏蓋を閉めます。「RGB1」~「VIDEO3」に接続する装置名を貼りマークに記入し、リモコンに貼り付けてください。 卓上装備には、オプションのモニター用ハンガー1 式(型名 MU-170C用ハンガー, コード番号 卓上装備埋込み装備 表示器 取付け要領構成表 対応機種 接続可能機種 解像度 信号形式 システム構成本機の特徴 はじめに取付け要領 Page 必ずお守りください 安全にお使いいただくために「このページは空白です。」 重要なお知らせ