Goldstar GBV441 owner manual Connections, Connecting Antenna/Cable TV to

Page 11
Disconnect the antenna leads from the rear of the TV.

Connections

ips

Depending on your TV and other equipment you wish to connect, there are various ways you could connect the DVD+VCR. Use connections described on pages 11-13. Please refer to the manuals of your TV, VCR, Stereo System or other devices as necessary to make the best connections.

For better sound reproduction, connect the DVD+VCR’s DVD/VCR AUDIO OUT jack to the audio in jacks of your amplifier, receiver, stereo or audio/video equipment. See Optional, Preferred TV Connections on pages 12-13.

Caution

Make sure the DVD+VCR is connected directly to the TV. Tune the TV to the correct video input channel.

Do not connect the DVD+VCR’s DVD/VCR AUDIO OUT jack to the phono in jack (record deck) of your audio system.

Do not connect your DVD+VCR via your VCR. The DVD image could be distorted by the copy protection system.

Connecting Antenna/Cable TV to

DVD+VCR

1

2 Identify the type of cable from your antenna. If it is a round cable as illustrated, it is a 75 ohm coaxial antenna cable. This cable will connect directly to the jack marked ANT.IN on your DVD+VCR.

ip

If your antenna lead wire is a flat type antenna cable, connect it to an Antenna Adapter (300-ohm to 75-ohm) (not supplied) and slip the Adapter onto the ANT.IN jack. The Adapter does not screw on to the DVD+VCR, it just slips over the jack.

Antenna Antenna

Cable TV

Wall Jack

Flat Wire

 

 

(300 ohm)

 

 

300/75 ohm

OR

OR

Adaptor

 

 

(Not supplied)

 

 

Rear of DVD+VCR

Without Cable Box

If your cable wire is connected to your TV without a converter or descrambler box, unscrew the wire from your TV and attach it to the ANT.IN jack on the DVD+VCR. Use the supplied round coaxial cable to connect between the DVD+VCR’s RF.OUT jack and the 75 ohm antenna input jack on the TV. With this connection, you can receive all midband, super band, and hyperband channels.

With Cable Box

If a converter is required in your cable system, follow the instruction below:

The cable hookup permits both TV and DVD+VCR operation.

To view or record CATV channel

1Tune the TV to the DVD+VCR output channel (CH 3 or 4).

2Set the DVD+VCR channel selector to the output channel of the Cable Converter box by using the CH/TRK (v/V) or number (0-9) of your DVD+VCR. (Example: CH3)

3Select the channel to view at the Cable Converter Box.

otes

With this connection, you CANNOT record one program while viewing another.

If you are using a cable box to tune channels, it is not nec- essary to do Auto Channel Programming as indicated on page 15.

Cable TV

Wall Jack

Back Panel of

Typical Cable Box

Rear of DVD+VCR

PREPARATION

11

Page 10 Page 12
Image 11
Page 10 Page 12
Contents DVD Player+ Video Cassette Recorder Regulatory Information FCC Part Safety PrecautionsImportant Safety Instructions Table of Contents Playable Discs Remote Control Battery InstallationRemote Control Operating Range Before UseSelecting the Viewing Source PrecautionsAbout Symbols Front Panel Controls REC Display WindowRemote Control ANT.IN Antenna Input Connections PanelVideo OUT DVD OUT Digital Audio OUT Coaxial DVD OUTConnections Connecting Antenna/Cable TV toAudio/Video connection Connections Basic TV ConnectionsOptional, Preferred TV Connections RF coaxial connectionAmplifier Receiver Accessory Audio/Video A/V Connections toDigital Multi-channel sound Menu Selection VCR Operation Setup On-Screen Display OSDOn-Screen Menus Setup Channel Selection VCR Operation Setup VCR Setup Menu OptionsManual Clock Set VCR Operation Setup Setting the ClockAuto Clock Set On-screen display operation DVD Operation Setup General ExplanationOn-Screen Display Picture DVD Operation Setup Initial SettingsGeneral Operation LanguageOthers DVD Operation SetupSound Rating DVD Changing the 4-digit passwordIf you forget your 4-digit password Parental ControlSpecial Effect Playbacks VCR Operation Normal PlaybackTo record one TV program while watching another Timer RecordingVCR Operation Normal Recording To pause recordingProgram Priority Checking Erasing Timer Record ProgrammingVCR Operation To extend the Recording Time Instant Timer RecordingChecking the Recording Time MTS Multi-Channel TV Sound Multichannel TV Sound Indicator MTSVHS Hi-Fi Stereo System MTS Broadcast Playback with Hi-Fi Stereo Audio SoundAdditional Information VCR Operation Tape Counter Memory FeatureDVD Operation Playing DVDs General FeaturesDVD Operation General Features Special DVD Features About WMA Window Media Audio Files About MP3Audio CD and MP3/WMA Disc Operation To flip the picture Jpeg File Operation Viewing Jpeg Files on a Disc JpegSelecting other Files Still PictureProgrammed Playback with Audio CDs and MP3/WMA Discs Programmed Playback CD MP3 WMATV Control Buttons By pressing You can Controlling Your TV with the Supplied RemoteControlling other TVs with the remote Code numbers of controllable TVsDVD+VCR TroubleshootingSymptom Cause Correction Moisture Condensation Language Code Language Code ListCode Country Country Code ListGeneral SpecificationsVCR Specifications DVD SpecificationsLG Electronics U.S.A., INC Sylvan Avenue Warranty Period HOW Service is HandledFor Warranty Service Customer INTER-ACTIVE Center Numbers
Top Page Image Contents