Troubleshooting
Check the following guide for the possible cause of a problem before contacting service. |
|
| |||
|
|
|
|
|
|
|
|
|
|
|
|
Symptom | Cause | Correction |
| ||
|
|
|
|
|
|
No power. | The power cord is disconnected. | Plug the power cord into the wall outlet |
| ||
|
| securely. | REFERENCE | ||
|
|
|
|
| |
The power is on, but | No disc is inserted. | DVD+VCR appears on the TV screen. | |||
Insert a disc or tape. (Check that the |
| ||||
the DVD+VCR does not | No tape is inserted. | disc or tape indicator in the display |
| ||
work. |
| window is lit.) |
| ||
No picture. | The TV is not set to receive DVD+VCR | Select the appropriate video input mode |
| ||
| signal output. | on the TV so the picture from the |
| ||
|
|
|
|
|
|
| TV/VCR mode for DVD+VCR is set to | Press the TV/VCR button on the remote |
| ||
| TV. | control repeatedly to choose VCR |
| ||
|
| mode. TV indicator disappears from the |
| ||
|
| display window. |
|
| |
| The video cable is not connected | Connect the video cable securely. |
| ||
| securely. |
|
|
|
|
|
|
|
|
|
|
| The connected TV power is turned off. | Turn on the TV. |
| ||
|
|
|
|
|
|
No sound. | The equipment connected with the | Select the correct input mode on the |
| ||
| audio cable is not set to receive | audio receiver so you can listen to the |
| ||
| DVD+VCR signal output. | sound from the DVD+VCR. |
| ||
|
|
|
|
|
|
| The audio cables are not connected | Connect the audio cables securely. |
| ||
| securely. |
|
|
|
|
|
|
|
|
|
|
| The power of the equipment connected | Turn on the equipment connected with |
| ||
| with the audio cables is turned off. | the audio cables. |
|
| |
| The Digital Audio Output is set to the | Set the Digital Audio Output to the |
| ||
| wrong position. | correct position, then turn on the |
| ||
|
| DVD+VCR again by pressing POWER. |
| ||
|
|
|
|
|
|
The playback picture is | The disc is dirty. | Clean the disc. |
| ||
poor. |
|
|
|
|
|
Tape heads are dirty. | Clean video heads. |
| |||
|
| ||||
|
|
|
|
|
|
| Tape is a rental or was recorded on | Use CH/TRK (v/V) for manual tracking |
| ||
| another VCR. | adjustment while tape is playing. |
| ||
|
|
|
|
| |
The DVD+VCR does | No disc is inserted. | Insert a disc or tape. (Check that the |
| ||
No tape is inserted. | disc or tape indicator in the display |
| |||
not start playback. |
| ||||
| window is lit.) |
| |||
|
|
| |||
|
|
|
|
|
|
| An unplayable disc is inserted. | Insert a playable disc. (Check the disc |
| ||
|
| type, color system, and Regional code.) |
| ||
|
|
|
|
|
|
| The disc is placed upside down. | Place the disc with the playback side down. |
|
| |
| The disc is not placed within the guide. | Place the disc on the disc tray correctly |
| ||
|
| inside the guide. |
|
| |
| The disc is dirty. | Clean the disc. |
|
| |
| The Rating level is set. | Cancel the Rating function or change |
| ||
|
| the rating level. |
| ||
The remote control | The remote control is not pointed at the | Point the remote control at the remote |
| ||
does not work properly. | remote sensor of the DVD+VCR. | sensor of the DVD+VCR. |
|
| |
| The remote control is too far from the | Operate the remote control within 23 ft |
| ||
| DVD+VCR. | (7 m). |
|
| |
| There is an obstacle in the path of the | Remove the obstacle. |
| ||
| remote control and the DVD+VCR. |
|
|
|
|
| The batteries in the remote control are | Replace the batteries with new ones. |
| ||
| dead. |
|
|
|
|
|
|
|
|
|
|
| This remote control uses the same | When using a VCR, first press the VCR |
| ||
| buttons for VCR and DVD functions | button. When using a DVD, first press |
| ||
| (ex. PLAY). | the DVD button. |
| ||
|
|
|
|
|
|
35