JVC BR-DV6000E instruction manual Presetting the time code, Rec-Run, Free-Run

TIME CODE – Presetting the time code –

Variable values can be set for the time code and the userÕs bit for efficient material management and editing.

SET button

DISP/8 button RESET button

OPERATE

Mini MENU DISP RESET A.DUB REC PLAY PAUSE

					PROFESSIONAL
; button	SEARCH–		SET	SEARCH+
						EJECT		REW	STOP	FF
	MIC	HOLD	BLANK	CUE UP
	PHONES		REC LEVEL					AUDIO	INPUT	REMOTE
						COUNTER MONITOR OUTPUT SELECT
						CTL	L	CH-1/2	DV
						TC	MIX	MIX	LINE
			CH-1/3	CH-2/4	BR-DV6000	UB	R	CH-3/4	Y/C	LOCAL
									(CPN)
HOLD button		9 button			: button	COUNTER switch

TC/UB/CLOCK(1/2) Menu screen

Ð Ð Ð T C / U B / C L O C K ( 1 / 2 )Ð Ð Ð

T C G S O U R C E		I N T E R N A L
T C G S E L E C T		P R E S E T
T C G M O D E		R E C - R U N
N D F / D F ( N T S C )		Ð Ð Ð
D F B I T ( P A L )		O N
T C D U P L I C A T E		O F F
T C O F F S E T		O F F
N E X T	P A G E
P A G E	B A C K

LCD display

CH1/3
						OVER
	48k L	40 30 20		10	0 dB
CH2/4
						OVER
RRUN TC 00H 00M 00S00F
STOP			SP222min
								e
		01/02/03		Y/C SYNC
							CF
		AM 01:23:45						r

Memo

●To stop the setting, press the HOLD button to return to the normal screen.

●To preset all digits to 0, press the RESET button when any of the digits is blinking.

●When the hour digit is blink- ing, the frame digit starts blinking when the ; button is pressed.

●If a userÕs bit is input with its all digits set as ÒFÓ, BR-DV6000 converts FFFFFFFF to FFFFFFFE before recording.

:Setting: ...TC/UB/CLOCK(1/2) Menu screen

Set TCG SOURCE to “INTERNAL”.

Set TCG SELECT to “PRESET”.

TCG MODE:

REC-RUN	: The time code runs only during recording.
FREE-RUN	: The time code runs from the point when the preset
	is completed.

❈In the case of the userÕs bit, setting is not required.

:Operation: ... Perform setting while checking the LCD display.

This section describes the setting of the time code. The setting of the userÕs bit is the same. Values that can be used to configure the userÕs bit are hexadecimal numeral from 0 Ð F.

1. Set the counter switch to TC.

(For userÕs bit, set the switch to UB.)

2. Press the DISP button to change the LCD to its enlarged dis- play mode.

3. In the STOP mode, press the HOLD button.

¥The hour digit of the counter starts blinking.

4.Press the 8 or 9 button to change the value.

5.Press the : or ; button to move blinking to the next digit.

6.Press the 8 or 9 button to change the value of the blinking digit.

7.Repeat steps 5 and 6 to perform the necessary settings.

8.Press the SET button to confirm the setting value and blink- ing of the counter stops.

E-59