JVC HR-J259EE, HR-J459EE specifications Recording, Timer again

Page 41

E

N

41

RECORDING

SYMPTOM

POSSIBLE CAUSE

CORRECTIVE ACTION

1.

Recording cannot be started.

● There is no cassette loaded, or the

Insert a cassette, or using adhesive

cassette loaded has had its Record

tape, reseal the slot where the tab

Safety tab removed.

was removed.

2.

TV broadcasts cannot be recorded.

● “F-1” has been selected as the input

Set to the desired channel.

mode.

3.

Tape-to-tape editing is not possible.

● The source (another video recorder,

Confirm that the source is properly

camcorder) has not been properly

connected.

connected.

● All necessary power switches have

Confirm that all units’ power switches

not been turned on.

are turned on.

● The input mode is not correct.

Set the input mode to “F-1”.

4.

Camcorder recording is not

● The camcorder has not been

Confirm that the camcorder is

possible.

properly connected.

properly connected.

● The input mode is not correct.

Set the input mode to “F-1”.

TIMER RECORDING

SYMPTOM

POSSIBLE CAUSE

CORRECTIVE ACTION

1.

Timer recording won’t work.

● The clock and/or the timer have

Re-perform the clock and/or timer

been set incorrectly.

settings.

● The timer is not engaged.

Press TIMER and confirm that “ä“ is

displayed on the display panel.

2.

On-screen timer programming is

● Timer recording is in progress.

Timer programming can’t be

not possible.

performed while a timer recording is

in progress. Wait until it finishes.

3.

“ä“ and “]“ on the display

● The timer is engaged but there’s no

Load a cassette with the Record

panel won’t stop blinking.

cassette loaded.

Safety tab intact, or cover the hole

using adhesive tape.

4.

The cassette is automatically

● The loaded cassette has had its

Remove the cassette and cover the

ejected, and “ä“ and “]“ on the

Record Safety tab removed.

hole with adhesive tape, or insert a

display panel won’t stop blinking.

cassette with the Record Safety tab

intact.

5.

“ä“ blinks for 10 seconds and the

● TIMER has been pressed when there

Check the programmed data and re-

Timer mode is disengaged.

are no programs in memory, or the

program as necessary, then press

timer record information has been

TIMER again.

programmed incorrectly.

6.

The cassette is automatically

● The end of the tape was reached

The programme may not have been

ejected, the power shuts off and

during timer recording.

recorded in its entirety. Next time

“ä“ and “]“ won’t stop

make sure you have enough time on

blinking.

the tape to record the entire

programme.

7.

SHOWVIEW does not timer-record

● The recorder’s channel positions

Refer to "Guide Program Number Set"

properly.

have been set incorrectly.

and re-perform the procedure

(☞ pg. 20).

Image 41

Contents HR-J459EE HR-J259EE Auto Head Cleaner Safety PrecautionsHR-J459EE HR-J259EEBasic Connections Check ContentsSituate Recorder Connect Recorder to MainsVideo Channel Set Access Video Channel SET ModeEN I Nitial Sett Ings With RF ConnectionPress to finish the setting Exit Video Channel SET ModeSET Video Channel With AV ConnectionSelect Language Auto Set UpSET Time SET DateStart Auto Channel SET Appears. When Auto Channel Set is completedPress Menu Auto SET screen AppearsAccess Initial SET Screen Access Main Menu ScreenSelect Language Turn on the RecorderClock Set Access Clock SET ScreenTurn the Recorder on SET DateInitial Settings ENABLE/DISABLE ON-SCREEN DisplayOn-Screen Displays Return to NormalColour System Set Access Main Menu ScreenMode Information on Colour SY Stem E NLoad a Cassette Basic PlaybackPoint Start PlaybackSearch Playback FeaturesPlayback Activate HIGH-SPEED SearchOverride Automatic Tracking Adjust Tracking ManuallyReturn to Automatic Tracking Activate Repeat PlaybackActivate Instant Review Activate Index SearchSkip Over Unwanted SectionsBasic Recording Recording Features Select Mode Access Mode SET ScreenS.T. Picture System EN RecordingOr press Record on the recorder RecordingPlayback EN Timer Recording SetupNumber Guide Program Number SetOr Push JOG% Enter Receiving Channel Position NumberPress Push JOG %Þor Timer Programming Press SP/LP to set the tape speed To disengage the timer, press Timer againVPS Recording on PDC Programme Delivery Control recording is notAccess Showview Express Timer ProgrammingAccess Programme Start TimeTimer Mode SET VPS ModeSET Tape Speed Engage RECORDER’SPress PROG. Check Check, Cancel And Replace ProgrammesPress PROG. Check again To check more informa Tion. Each time you press PROG. CHECK, the nextReturn to Normal Screen Auto SP→LP Timer HR-J459EE onlyAuto Timer Automatic Satellite Programme Recording REC Link indicatorSET Tape Speed HR-J459EE only Before performing the following stepsTV Multi-brand Remote Control Special Features E NControl Your TV Using Additional Buttons SET TV Brand CodeEdit To Another Video Recorder Input ModeMake Connections SET Recording DECK’SSource player Edit From a Camcorder Or Another Video RecorderSET RECORDER’S Input Auto CH SET, then Perform Auto Channel SETTuner SET After Scan Completed Is displayed on the screen On the remote controlFor about 5 seconds, Channel List screenAccess Channel List Screen Access Main MenuSelect Band Input ChannelPerform Tuning Access ManualSelect Item Delete ChannelSet Stations a Switch StationsEN Tuner SET Select Channel Select Station Name CharacterPosition Select TV SystemTV Station And ID List Playback Recording Questions and Answer S E NSet the TV receiver to the Video If you are using the AV connectionSet the TV to its AV mode Recording Timer againOubleshooting Other ProblemsFront View IndexDisplay Panel EN IndexRemote Control Maximum recording time Infrared remote control unitLP J459EE only Rotary two-head helical scanMemo HR-J459/259EE