JVC HR-J580EK manual Recording

Page 52

52

subsidiary information

SYMPTOM

POSSIBLE CAUSE

CORRECTIVE ACTION

RECORDING

1.Recording cannot be started.

2.TV broadcasts cannot be recorded.

3.Tape-to-tape editing is not possible.

4.Camcorder recording is not possible.

¥There is no cassette loaded, or the cassette loaded has had its record safety tab removed.

¥L-1 has been selected as the input mode.

¥The source (another VCR, camcorder) has not been properly connected.

¥All necessary power switches have not been turned on.

¥The input mode is not correct.

¥The camcorder has not been properly connected.

¥The input mode is not correct.

Insert a cassette, or using adhesive tape, cover the hole where the tab was removed.

Set to the desired preset.

Confirm that the source is prop- erly connected.

Confirm that all unitsÕ power switches are turned on.

Set the input mode to L-1.

Confirm that the camcorder is properly connected.

Set the input mode to L-1.

TIMER RECORDING

1.Timer recording wonÕt work.

2.Timer programming is not possible.

¥The clock and/or the timer have been set incorrectly.

¥The timer is not engaged.

¥Timer recording is in progress.

Re-perform the clock and/or timer settings.

Press cand confirm that cis displayed on the display panel.

Timer programming canÕt be performed while a timer recording is in progress. Wait until it finishes.

3.con the display panel wonÕt stop blinking.

4.c, Uand ,on the display panel wonÕt stop blinking.

¥The timer is engaged but thereÕs no cassette loaded.

¥The loaded cassette has had its record safety tab removed.

¥The end of the tape was reached during timer recording.

Load a cassette with the record safety tab intact.

Remove the cassette and cover the hole with adhesive tape, or insert a cassette with the record safety tab intact.

The programme may not have been recorded in its entirety. Next time make sure you have enough time on the tape to record the entire programme.

5.cblinks for 10 seconds and the Timer mode is disengaged.

¥chas been pressed when there are no programmes in memory, or the timer record information has been pro- grammed incorrectly.

Check the programmed data and re-programme as necessary, then press cagain.

6.The VIDEO Plus+ system does not timer record properly.

¥The VCRÕs preset positions have been set incorrectly.

Refer to Guide Program Numbers (pg. 23) and re-perform the procedure.

Image 52
Contents HR-J580EK Safety Precautions If in doubt Ñ consult a competent electricianMoisture Condensation Some DoÕs And DonÕts On The Safe Use Of EquipmentContents Front panel Rear panel Diagram Key Front PanelWelcome to JVC Getting Everything ReadyPerform Auto Setup pg Auto Setup Three-Step Quick StartThree step quick start Preset Download Start Preset DownloadCheck the Results Finish OffThree-step quick start Basic Features Playback Load a Video CassettePlay Stop & EjectVideo Heads Cleaning Rewind and Fast ForwardPlayback Features Pause During PlaybackSingle Frame Movement Slow MotionVariable Speed Search High Speed SearchRecording Choose a ProgrammeSet the Tape Speed Start RecordingDisplay Tape Remaining Time Resetting the CounterChange Display Information Instant Timer Recording Recording Resume FunctionManually Setting Guide Program Numbers Channel Mapping Guide NumbersGet to the Video Plus + Screen Enter the PlusCode NumberEngage Timer Mode Return to Normal ScreenGet to the Programme Screen Express Timer ProgrammingEnter Programme Details Timer Recording To Start Soon Check, Cancel & Change Programmes When Programmes Overlap Each OtherAdvanced Features Manual Tracking Picture QualityPicture Control Recording and Playback Using B.E.S.T Avoiding B.E.S.T. Time DelayB.E.S.T PictureÊSystem Turning B.E.S.T. on or OFFNicam Stereo and Bilingual Broadcasts Sound ModesSoundtrack Selection Finding Specific Scenes Skip SearchIndex Search Instant ReViewTV Auto Power On Link FunctionsNexTView Link VCR Auto StandbyDirect Rec Editing Using Another VCR EditingEditing from a Camcorder Start recorder Press TOther Functions On-Screen Display O.S.DPower Save Mode Auto SP aLP TimerRepeat Playback Auto TimerNext Function Memory Connection to a Stereo System Access Video Channel Mode Exit Video Channel Set ModeVideo Channel Set Set Video ChannelAuto Channel Setup Tuner SetManual Channel Setup Change Station Name Delete a ChannelChange Station Preset Position Fine-Tuning Stored Channels TV Station ID GuideTV Station Channel Number Guide BBC1 BBC2 ITV CH4 CH5Setting the Clock Clock SetQuestions and Answers PlaybackTroubleshooting Symptom Possible CauseRecording Other Problems List of Terms Memo HR-J580EK