JVC HR-672, HR-J670, HR-671, HR-674, HR-272EU Programme Recording, 30 EN, Select the L-2 Select mode

Page 30

30 EN

TIMER RECORDING (cont.)

Automatic Satellite

Programme

Recording

This function allows you to automatically record a satellite programme which is timer-programmed on your external satellite receiver. Connect a satellite receiver to the recorder and programme the timer on the satellite receiver. The recorder starts or stops recording by the signals input from the satellite receiver. After recording, the recorder’s power shuts off automatically.

ATTENTION

●Be sure not to turn on the satellite receiver before the programme is executed; otherwise, the recorder will start recording when the satellite receiver’s power is turned on.

●If you have connected another appliance other than a satellite receiver to the AV2 (L-2) IN/DECODER connector, be sure not to engage the Auto Satellite Programme Recording mode; otherwise, the recorder will start recording when the connected appliance’s power is turned on.

●Auto Satellite Programme Recording and timer-recording cannot be done at the same time.

Before performing the following steps:

●Make sure the satellite receiver is connected to the recorder’s AV2 (L-2) IN/DECODER connector. ( pg. 33)

●Programme the timer on the satellite receiver.

●Insert a cassette with the safety tab in place.

SAT#indicator

A Select the L-2 SELECT mode.

Set “L-2 SELECT” to “L-2” or “SAT” ( pg. 39).

● When you select “SAT”, refer to “IMPORTANT” on page 33.

B Set the tape speed. (HR-J670/671/672/673/674/470/ 472EU only)

Press SP/LP (p).

C Engage the Auto Satellite Programme

Recording mode.

Press and hold SAT# for about 2 seconds. The SAT# indicator lights up and the recorder turns off automatically.

NOTES:

●To disengage the Auto Satellite Programme Recording mode, press SAT#. The SAT#indicator goes off.

●If the recorder’s power is off, it is not possible to engage the Auto Satellite Programme Recording mode.

●In step 3, if the SAT#indicator does not light but instead blinks quickly even though your satellite receiver’s power is off, Auto

Satellite Programme Recording will not work properly with that satellite receiver*. If this is the case, perform “Express Timer Programming” ( pg. 26) to timer-record a satellite programme.

*Some satellite receivers output signals even if the power is off. Auto Satellite Programme Recording is not possible with those satellite receivers.

●The SAT#indicator blinks while Auto Satellite Programme Recording is in progress.

●For timer programming of the satellite receiver, refer to the instruction manual of the satellite receiver.

●Auto Satellite Programme Recording is not possible if your satellite receiver does not have a timer.

●Pressing the recorder’s 1button while Auto Satellite Programme Recording is in progress turns off the recorder’s power and disengages the Auto Satellite Programme Recording mode.

●If there are more than one satellite programmes you wish to record with Auto Satellite Programme Recording, it is not possible to set different tape speeds for each programme.

●Depending on the type of satellite receiver, the recorder may not record a slight portion of the beginning of the programme or may record slightly longer than the actual length of the programme.

●If you engage the Auto Satellite Programme Recording mode when the satellite receiver’s power is on, the recorder will not start Auto Satellite Programme Recording even though the SAT#indicator blinks. When the satellite receiver shuts off once and is turned back on again, the recorder starts recording.

●You can also record a programme from your cable system in the same way if the system has a timer.

●The B.E.S.T. system ( pg. 23) does not work while Auto Satellite Programme Recording is in progress.

●Just Clock ( pg. 48) does not work when the Auto Satellite Programme Recording mode is engaged.

●When the Auto Satellite Programme Recording mode is engaged, or the recorder’s power is turned off after Auto Satellite Programme Recording is finished, the recorder will not enter the Timer mode even though “AUTO TIMER” is set to “ON”.

●After Auto Satellite Programme Recording, the number of recorded programmes will not be displayed on the front display panel for the Instant ReView function ( pg. 18).

Page 29 Page 31
Image 30
Page 29 Page 31
Contents Video Cassette Recorder English Safety Precautions Moisture Condensation Front View Front Display Panel How To Use Operating JVC TVsConnect the recorder to TV Check the contentsSituate the recorder Connect the recorder to mainsAuto Set Up Turn on the recorderSelect your country Press rt to select your language code Perform Auto Set UpSelect the language Press rt to select Auto and press OK or eSet the video channel Perform Preset Download10 EN Press rt to select CH - and press OK or eLanguage for the on-screen display Just ClockLanguage Access the Main Menu screenAccess the Country Set screen 12 ENAttach the Satellite Controller Installing Satellite ControllerSituate the Satellite Controller Make connectionsSetting satellite receivers brand and channel 14 ENTV Auto Power On NexTView LinkVCR Auto Standby Direct Rec Basic Playback 16 ENVariable Speed Search Slow MotionHigh-Speed Search Pause during playback18 EN Manual TrackingInstant ReView Next Function Memory Index SearchSkip Search Repeat Playback20 EN Watching Another Instant Timer Recording ITREngage the ITR mode Set the recording durationTape Remaining Time Reset the counter22 EN Set the counter displayPlayback RecordingBefore performing the Showview Timer Programming Access the Showview screenAccess the Showview Program screen 24 ENSatellite Receiver Users Set the VPS/PDC modeEngage the recorder’s timer mode Guide Program Number SetExpress Timer Programming 26 EN Enter the channel position To Timer-Record Weekly Or Daily Serials VPS/PDC Recording Press PR +28 EN Select the programme to modify Cancel or change programme settingConfirm the overlapping programmes Overlapping programmes blink on the TV screenProgramme Recording Select the L-2 Select modeEngage the Auto Satellite Programme Recording mode 30 ENEdit From a Camcorder Set the recorder’s input modeSet the edit mode Start the camcorder32 EN Set the input mode of recording deckAnother Video Recorder Start the source playerConnecting To a Satellite Receiver Satellite receiver Decoder Back of recorderConnect the decoder Select the input mode34 EN Set the tunerHR-J670/671/672/673/674EU only Make connectionsSelect the mode Mode SetAccess the Mode Set screen Select the mode settingWhen this function is set to ON, the timer is You can set the B.E.S.T. Biconditional Equalised SignalThis feature helps you to adjust the playback picture Off, and automatically disengaged when the recorder is38 EN For ExampleAbout Ntsc Playback 40 EN Access the Auto Channel Set screenTuner Set Auto Channel SetPerform Auto Channel Set View the Confirmation screenPress OK twice 42 EN Manual Channel SetWhen Receiving a Scrambled Broadcast Delete a Channel44 EN Set Stations aSet Stations B TV Station And ID List Station NameVideo Channel Set Access the Video Channel Set modeExit the Video Channel Set mode 46 ENGuide Program Number Showview SetupGuide Program Number Set Enter the Guide Program numberAccess the Clock Set screen Clock Set48 EN Set the source channel position for clock data Set the date and timeSet Just Clock Start the clock operationTroubleshooting 50 ENRecording Other Problems 52 ENPlayback 54 EN Language Manual Channel Set Manual Tracking Mode Set Auto Set UpConnecting To a Satellite Receiver Delete a Channel Timer warning display Tuner SetInternational Telephone Language Code Country CodeSee Instructions  pg
Related manuals
Manual 56 pages 11.98 Kb Manual 56 pages 18.54 Kb
Top Page Image Contents