JVC HR-J730KR On-Screen Timer Programming, Access ON-SCREEN, Menu, Access Program SET Screen

Page 32

32TIMERRECORDING(cont.)

On-Screen

Timer

Programming

OK

6

q

 

CH

 

 

 

1

2

3

NUMBER

4

5

6

 

7

8

9

 

 

0

 

CH

OK

MENU

PUSH JOG

ILLUMI GUIDE

When Using The Illumi-Guide Feature

● Buttons light or blink on the remote control for approximately 10 seconds. If the button or buttons extinguish during timer programming, press ILLUMI GUIDE and the button or buttons previously lit or blinking come back on. If the button or buttons do not re-light or start blinking again, press MENU as many times as necessary to return to the normal screen and extinguish all illuminated buttons, and re-perform the timer programming procedure from the beginning.

● If for some reason the remote control's signal is not received by the VCR, press MENU as many times as necessary to return to the normal screen and extinguish all illuminated buttons, and re-perform the timer programming procedure from the beginning.

You can directly program the VCR’s timer to record up to 8 shows, as far as a year in advance. Remember, the clock must be set before you can program the timer (☞ pg. 5).

Or you can use the Illumi-Guide feature, where the remote control tells you which button to press next by lighting it up. To use the Illumi-Guide feature, with the TV/VCR switch set to "VCR", press ILLUMI GUIDE before performing step 2. (MENU, REW, PLAY, FF light up at this time.)

If you aren't going to use the Illumi-Guide feature, go directly to step 1.

LOAD A CASSETTE

1 Make sure the record safety tab is intact. If not, cover the hole with adhesive tape, then load.

●The VCR comes on, and the counter is reset, automatically.

●If watching channel 3 or 4, press TV/VIDEO to select the VIDEO mode. VIDEO is displayed on the front display panel.

 

ACCESS ON-SCREEN

2

MENU

Press MENU as many times as necessary to bring up the

Main Menu screen.

● If you are using the Illumi-Guide feature, OK blinks

 

 

when the following buttons are lit: NUMBER keys

 

(0 – 9), CANCEL and MENU.

ACCESS PROGRAM SET SCREEN

 

Make sure the arrow is to

PROGRAM 1

 

the left of "PROGRAM

 

 

 

3 SET", then press OK.

DATE

- - / - -

START

- - : - - AM

 

● If you are using the

STOP

- - : - - AM

 

CHANNEL

- - SP

 

Illumi-Guide feature, OK

PRESS NUMBER KEY(0-9)

 

blinks when the

 

OR (5,°), THEN (OK)

 

following buttons are lit:

 

PRESS (MENU) TO END

 

NUMBER keys (0 – 9),

 

 

 

PUSH JOG, CANCEL and MENU.

 

 

 

 

 

SELECT PROGRAM

 

4

NUMBER

 

 

Press the appropriate NUMBER keys or CH5°or PUSH

JOG 5°to select a vacant program number, then press

OK. The first time you do this, all numbers will be vacant,

 

so just press OK when the screen appears.

 

●If you are using the Illumi-Guide feature, OK blinks when the following buttons are lit: NUMBER keys (0 – 9), PUSH JOG, CANCEL and MENU.

Page 31 Page 33
Image 32
Page 31 Page 33
Contents HR-J730KR Dear Customer Do not place the VCRContents Basic Connections Clock Tuner Perform Auto Channel SET Return to Normal ScreenAccess Tuner SET Screen Access AFC ScreenMake Selection Store Desired ChannelCode Setup Access Main Menu ScreenInput Guide Channel Number Access G-CODE SET-UP ScreenAccess Guide Channel SET Screen Return to Normal Return to G-CODE SET UP ScreenInput Receiving Channel Number Simple Playback Load a CassetteFind Program Start Point Start PlaybackSimple Recording Pause During Playback Activate FRAME-BY Frame PlaybackStill Picture/Frame-By- Frame Playback Slow Motion/ Reverse Slow MotionActivate VARIABLE-SPEED Search Activate HIGH-SPEED SearchVariable-Speed Search Reverse Play High-Speed SearchEngage Manual Tracking Mode Adjust Manual TrackingRE-ENGAGE Automatic Tracking Manual TrackingAccess Function SET Access Audio MonitorSelect The Soundtrack MixSuperimpose Access Distant Code Skip Over Unwanted SectionsStart Repeat Stop RepeatActivate Instant Review Activate CounterMemory Return to Counter Position ZeroTape Position Indicator Make ConnectionNext-Function Memory AV Compu Link PlaybackAccess Special Enable AV Compu LinkFunction Screen PlaybackAccess B.E.S.T. Picture System Screen Select ModeS.T. Picture System PreparationRecording Press and hold RECQuality of the tape Use, then recording Begins with the picture Level optimizedPlayback Tape in useEngage TV Mode Reset Counter to ZeroRecording Select Channel for ViewingSTereo indicator Receiving Stereo And Bilin- gual ProgramsTo Record Stereo And Bilin- gual Programs Select STEREO/BILINGUAL at the Audio Select screen pgAccess Audio Select To Record Monaural Pro- gramsPlace the arrow next to Audio Select by pressing Mono by pressingInstant Timer Recording ITR Engage ITR ModeSET Recording Duration Press RECEnter G-CODE Number Code Timer ProgrammingAccess G-CODE Screen Engage Timer Mode DataOn-Screen Timer Programming Access ON-SCREENAccess Program SET Screen MenuSET Program Information ExampleDisengage Timer Cancel a ProgramRE-ENGAGE Timer Check And Cancel ProgramsAccess Auto SP/EP Auto SP/EP TimerPlace the arrow next to Auto SP/EP Timer by Pressing CH 5 or Push JOG 5, then press OKAccess Auto Timer Auto TimerSpecial Features 19, 20Edit From a Camcorder Start Recorder SET RECORDER’S Input Mode Edit To Or From AnotherLoad Cassettes Start PlayerSET Input Mode Locate Start PointEngage Audio Dubbing Start DubbingLoad Source Cassette Random As- semble EditingPrepare for Editing END R.A. Edit Start R.A. EditTroubleshooting Cassette gets stuck partwayTimer again Re-perform the G-Code setup Doesn’t work properlyQuestions and Answers EIA monochrome signal Maximum recording time 210 min. with ST-210 video630 min. with ST-210 video Frequency-synthesized tunerIndex Remote Control Provided Front Display PanelHR-J730KR
Top Page Image Contents