JVC HR-J730KR manual Basic Connections

Page 4

4INSTALLINGYOURNEWVCR

Basic Connections

Antenna or Cable

Coaxial Cable

Flat Feeder

ANTENNA-

IN (Antenna

	AC Power	Matching Transformer	or Cable
	AC Power		input)
	Cord		input)
	Cord
	Back of VCR		RF
		Video Cable	RF
		Video Cable	OUT
	AC	(not supplied)	OUT
	AC	(not supplied)
	Outlet

Audio Cable (not supplied)

RF Cable (supplied)

75 ohm terminal

300 ohm terminal

TV

1

2

3

4

5

CHECK CONTENTS

Make sure the package contains all of the accessories listed in “SPECIFICATIONS” (☞ pg. 47).

SITUATE VCR

Place the VCR on a stable, horizontal surface.

CONNECT VCR TO TV

The connection method you use depends on the type of TV you have.

RF Connection

●To Connect To A TV With NO AV Input Terminals . . .

a– Disconnect the TV antenna from the TV.

b– Connect the TV antenna cable to the ANT IN jack on the rear of the VCR.

c– Connect the supplied RF cable between the RF OUT jack on the rear of the VCR and the TV’s antenna terminal.

AV Connection

●To Connect To A TV With AV Input Terminals . . .

a– Connect the antenna, VCR and TV as shown in the illustration.

b– Connect an Audio/Video Cable between the AUDIO OUT and VIDEO OUT jacks on the rear of the VCR and the AV IN jacks on the TV.

CONNECT VCR TO

POWER SOURCE

Connect the power plug to an AC outlet.

FINAL PREPARATION FOR USE

Select the VCR channel (3 or 4) by setting the switch on the rear of the VCR as shown in the illustration.

Turn on the power to the TV. You are now able to perform simple playback (☞ pg. 12) and recording (☞ pg. 13).

Back of VCR

RF OUT

CH3 CH4

NOTES:

●The VCR channel is the channel on the TV which will display the audio and video signals from the VCR. The VCR's CH3- CH4 switch sets the VCR channel to CH3 or CH4.

●The CH3–CH4 switch is preset to the CH3 position. Set to CH4 if CH3 is used for broadcasting in your area.

●If your TV has no AV input terminals, set the channel on the TV to correspond to the CH3–CH4 switch on the back of the VCR.

●Even if your TV has AV input terminals, you must connect it

to the VCR using an RF cable in order to record one show while watching another (☞ pg. 26).

●For full identification of the VCR's rear panel, refer to the Index (REAR VIEW ☞ pg. 48).

Image 4

Contents HR-J730KR Dear Customer Do not place the VCRContents Basic Connections Clock Tuner Perform Auto Channel SET Return to Normal ScreenAccess Tuner SET Screen Access AFC ScreenMake Selection Store Desired ChannelCode Setup Access Main Menu ScreenAccess Guide Channel SET Screen Access G-CODE SET-UP ScreenInput Guide Channel Number Input Receiving Channel Number Return to G-CODE SET UP ScreenReturn to Normal Simple Playback Load a CassetteFind Program Start Point Start PlaybackSimple Recording Pause During Playback Activate FRAME-BY Frame PlaybackStill Picture/Frame-By- Frame Playback Slow Motion/ Reverse Slow MotionActivate VARIABLE-SPEED Search Activate HIGH-SPEED SearchVariable-Speed Search Reverse Play High-Speed SearchEngage Manual Tracking Mode Adjust Manual TrackingRE-ENGAGE Automatic Tracking Manual TrackingAccess Function SET Access Audio MonitorSelect The Soundtrack MixSuperimpose Access Distant Code Skip Over Unwanted SectionsStart Repeat Stop RepeatActivate Instant Review Activate CounterMemory Return to Counter Position ZeroTape Position Indicator Make ConnectionNext-Function Memory AV Compu Link PlaybackAccess Special Enable AV Compu LinkFunction Screen PlaybackAccess B.E.S.T. Picture System Screen Select ModeS.T. Picture System PreparationRecording Press and hold RECQuality of the tape Use, then recording Begins with the picture Level optimizedPlayback Tape in useEngage TV Mode Reset Counter to ZeroRecording Select Channel for ViewingSTereo indicator Receiving Stereo And Bilin- gual ProgramsTo Record Stereo And Bilin- gual Programs Select STEREO/BILINGUAL at the Audio Select screen pgAccess Audio Select To Record Monaural Pro- gramsPlace the arrow next to Audio Select by pressing Mono by pressingInstant Timer Recording ITR Engage ITR ModeSET Recording Duration Press RECAccess G-CODE Screen Code Timer ProgrammingEnter G-CODE Number Engage Timer Mode DataOn-Screen Timer Programming Access ON-SCREENAccess Program SET Screen MenuSET Program Information ExampleDisengage Timer Cancel a ProgramRE-ENGAGE Timer Check And Cancel ProgramsAccess Auto SP/EP Auto SP/EP TimerPlace the arrow next to Auto SP/EP Timer by Pressing CH 5 or Push JOG 5, then press OKAccess Auto Timer Auto TimerSpecial Features 19, 20Edit From a Camcorder Start Recorder SET RECORDER’S Input Mode Edit To Or From AnotherLoad Cassettes Start PlayerSET Input Mode Locate Start PointEngage Audio Dubbing Start DubbingPrepare for Editing Random As- semble EditingLoad Source Cassette END R.A. Edit Start R.A. EditTroubleshooting Cassette gets stuck partwayTimer again Re-perform the G-Code setup Doesn’t work properlyQuestions and Answers EIA monochrome signal Maximum recording time 210 min. with ST-210 video630 min. with ST-210 video Frequency-synthesized tunerIndex Remote Control Provided Front Display PanelHR-J730KR