JVC HR-J730KR manual Dear Customer, Do not place the VCR

Page 2

2

Dear Customer,

Thank you for purchasing the JVC VHS video cassette recorder. Before use, please read the safety information and precautions contained in the following pages to ensure safe use of your new VCR.

CAUTIONS

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK.

DO NOT REMOVE COVER (OR BACK).

NO USER-SERVICEABLE PARTS INSIDE.

REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.

The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.

WARNING:

TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE.

CAUTION:

This video cassette recorder should be used with AC 110V–220V`, 60Hz only.

To prevent electric shocks and fire hazards, DO NOT use any other power source.

CAUTION:

TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT, FULLY INSERT.

ATTENTION:

POUR ÉVITER LES CHOCS ÉLECTRIQUES, INTRODUIRE LA LAME LA PLUS LARGE DE LA FICHE DANS LA BORNE CORRESPONDANTE DE LA PRISE ET POUSSER JUSQU'AU FOND.

Note to CATV system installer:

This reminder is provided to call the CATV system installer's attention to Article 820-40 of the NEC that provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the grounding system of the building, as close to the point of cable entry as practical.

CAUTION:

Changes or modifications not approved by JVC could void user's authority to operate the equipment.

Failure to heed the following precautions may result in damage to the VCR, remote control or video cassette.

1.DO NOT place the VCR . . .

... in an environment prone to extreme temperatures or humidity.

... in direct sunlight.

... in a dusty environment.

... in an environment where strong magnetic fields are generated.

... on a surface that is unstable or subject to vibration.

2.DO NOT block the VCR’s ventilation openings.

3.DO NOT place heavy objects on the VCR or remote control.

4.DO NOT place anything which might spill on top of the VCR or remote control.

5.AVOID violent shocks to the VCR during transport.

**MOISTURE CONDENSATION

Moisture in the air will condense on the VCR when you move it from a cold place to a warm place, or under extremely humid conditions—just as water droplets form on the surface of a glass filled with cold liquid. Moisture condensation on the head drum will cause damage to the tape. In conditions where condensa- tion may occur, keep the VCR’s power turned on for a few hours to let the moisture dry.

**ABOUT HEAD CLEANING

Accumulation of dirt and other particles on the video heads may cause the playback picture to become blurred or interrupted. Be sure to contact your nearest JVC dealer if such troubles occur.

HOW TO USE THIS INSTRUCTION MANUAL

All major sections and subsections are listed in the Table Of Contents on page 3. Use this when searching for information on a specific procedure or feature.

The Index on pages 48 – 49 lists frequently-used terms, and the number of the first page on which they are used or explained in the manual. This section also illustrates the controls and connections on the front and rear panel, the front display panel and the remote control.

The mark signals a reference to another page for instructions or related information.

Operation buttons necessary for the various procedures are clearly indicated through the use of illustrations at the beginning of each major section.

BEFORE YOU INSTALL YOUR NEW VCR . . .

. . . please read thoroughly the cautions on this page.

Cassettes marked "VHS" (or "S-VHS") can be used with this video cassette recorder. However, only "VHS" recordings can be played back in this model.

HQ VHS is compatible with existing VHS equipment.

G-Code is a trademark applied for by Gemstar Development Corporation.

G-Code system is manufactured under licence from Gemstar Development Corporation.

Image 2
Contents HR-J730KR Dear Customer Do not place the VCRContents Basic Connections Clock Tuner Perform Auto Channel SET Return to Normal ScreenMake Selection Access Tuner SET ScreenAccess AFC Screen Store Desired ChannelCode Setup Access Main Menu ScreenInput Guide Channel Number Access G-CODE SET-UP ScreenAccess Guide Channel SET Screen Return to Normal Return to G-CODE SET UP ScreenInput Receiving Channel Number Find Program Start Point Simple PlaybackLoad a Cassette Start PlaybackSimple Recording Still Picture/Frame-By- Frame Playback Pause During PlaybackActivate FRAME-BY Frame Playback Slow Motion/ Reverse Slow MotionVariable-Speed Search Reverse Play Activate VARIABLE-SPEED SearchActivate HIGH-SPEED Search High-Speed SearchRE-ENGAGE Automatic Tracking Engage Manual Tracking ModeAdjust Manual Tracking Manual TrackingSelect The Soundtrack Access Function SETAccess Audio Monitor MixSuperimpose Start Repeat Access Distant CodeSkip Over Unwanted Sections Stop RepeatMemory Activate Instant ReviewActivate Counter Return to Counter Position ZeroNext-Function Memory Tape Position IndicatorMake Connection AV Compu Link PlaybackFunction Screen Access SpecialEnable AV Compu Link PlaybackS.T. Picture System Access B.E.S.T. Picture System ScreenSelect Mode PreparationQuality of the tape Use, then recording RecordingPress and hold REC Begins with the picture Level optimizedPlayback Tape in useRecording Engage TV ModeReset Counter to Zero Select Channel for ViewingTo Record Stereo And Bilin- gual Programs STereo indicatorReceiving Stereo And Bilin- gual Programs Select STEREO/BILINGUAL at the Audio Select screen pgPlace the arrow next to Audio Select by pressing Access Audio SelectTo Record Monaural Pro- grams Mono by pressingSET Recording Duration Instant Timer Recording ITREngage ITR Mode Press RECEnter G-CODE Number Code Timer ProgrammingAccess G-CODE Screen Engage Timer Mode DataAccess Program SET Screen On-Screen Timer ProgrammingAccess ON-SCREEN MenuSET Program Information ExampleRE-ENGAGE Timer Disengage TimerCancel a Program Check And Cancel ProgramsPlace the arrow next to Auto SP/EP Timer by Access Auto SP/EPAuto SP/EP Timer Pressing CH 5 or Push JOG 5, then press OKAccess Auto Timer Auto TimerSpecial Features 19, 20Edit From a Camcorder Start Recorder Load Cassettes SET RECORDER’S Input ModeEdit To Or From Another Start PlayerEngage Audio Dubbing SET Input ModeLocate Start Point Start DubbingLoad Source Cassette Random As- semble EditingPrepare for Editing END R.A. Edit Start R.A. EditTroubleshooting Cassette gets stuck partwayTimer again Re-perform the G-Code setup Doesn’t work properlyQuestions and Answers 630 min. with ST-210 video EIA monochrome signalMaximum recording time 210 min. with ST-210 video Frequency-synthesized tunerIndex Remote Control Provided Front Display PanelHR-J730KR