JVC HR-J745EK, HR-J249EK instruction manual Video Channel Set, With RF Connection

Page 6

6INITIALSETTINGS

Video Channel Set

Video Channel (RF Output Channel) is the channel on which your TV receives picture and sound signals from the video recorder through the RF cable.

If you have connected the video recorder to your TV via the provided RF cable only (RF connection) – Go to "With RF Connection" below.

If you have connected the video recorder to your TV via both the provided RF cable and a 21-pin SCART cable (AV connection) – Go to "With AV Connection" on next page.

IMPORTANT:

Before performing the following steps, make sure the recorder's power is off and there is no cassette inserted in the recorder.

4

With RF Connection

 

 

 

 

ACCESS VIDEO CHANNEL SET

 

MODE

 

Hold down STOP on the recorder until the display

q

1 panel shows the following.

 

PROG.+/–

 

 

 

 

STOP 1

 

Set your TV to UHF channel 52.

 

 

 

 

 

 

 

2

SET VIDEO CHANNEL

2

TV

 

 

 

 

 

If the two vertical white bars appear clearly on the

 

 

 

 

 

 

 

 

 

 

 

 

4

screen as shown in the illustration at bottom left, go

 

 

 

 

 

 

 

to step 3.

 

 

 

 

 

 

 

If the two vertical white bars do not appear clearly,

 

 

 

 

 

 

 

 

press TV PROG.+ or to set the video recorder to a

 

 

 

 

 

 

 

 

vacant channel between 22 and 69 which is not

 

 

 

2

 

 

 

 

occupied by any local station in your area.

 

 

1

2

3

 

 

 

 

 

 

 

 

(Ex.) If channel 36 is available in your area

 

 

 

 

 

 

 

 

 

 

4

5

6

 

 

 

 

 

 

 

7

8

9

 

 

 

 

 

 

 

 

0

4

 

 

 

Then set your TV to UHF channel 36 and check if the

 

 

 

 

 

TV PROG. 2

 

two vertical white bars appear clearly on the screen; if

 

 

 

 

 

 

so, go to step 3. If not, re-set the video recorder to

 

 

 

 

 

 

another vacant channel and try again.

 

 

 

 

 

 

 

 

NOTES:

 

 

 

 

 

 

 

 

If you set the video recorder to a channel which is

 

 

 

 

 

 

 

 

occupied by a local station or has neighbouring

 

 

 

 

 

 

 

 

channels that are occupied by local stations, the

 

 

 

 

 

 

 

 

picture reception quality will be affected and some

 

 

 

 

 

 

 

 

interference noise will appear on the TV screen. Be

 

 

 

 

 

 

3

 

sure to select a vacant channel which has no

 

 

 

 

3

OK

 

broadcast on neighbouring channels.

 

 

 

 

 

If you cannot obtain the two vertical white bars

 

 

1

 

 

 

 

 

 

 

 

 

 

 

clearly with any channel between 22 and 69, consult

 

 

 

 

 

 

 

 

your JVC dealer.

 

 

 

 

 

 

 

 

EXIT VIDEO CHANNEL SET MODE

TEST SIGNAL

The channel on which the screen to

3 Press OK.

 

 

the left appear clearly in step 2 is

 

TURN OFF THE RECORDER

 

 

your Video Channel.

 

 

4 Press

.

 

 

 

 

 

 

 

To view picture signals from the video recorder, set your TV to the Video Channel.

After you finish this step, go to "Auto Set Up" on page 8.

Image 6
Contents HR-J745EK Safety Precautions Do not place the recorderStep Quick SET UP Situate Recorder Check ContentsBasic Connections Connect Recorder to MainsBack of HR-J745EK Back of HR-J249EK Video Channel Set With RF ConnectionSET Video Channel Access Video Channel SET ModeExit Video Channel SET Mode With AV ConnectionAuto Set Up Perform Auto SET UPIf auto channel set has succeeded but auto clock set has not Video Plus+ Setup Make List of Stored Station Names Preset PositionsGuide Program Number Set Close Menu Confirm Preset Position NumberWhen Using a Satellite Receiver And/Or Cable System BackPoint Basic PlaybackLoad a Cassette Start PlaybackPlayback Features Pause During PlaybackActivate SLOW-MOTION Playback Override Automatic Tracking Adjust TrackingActivate HIGH-SPEED Search ManuallyActivate Instant Review Activate 3R PictureActivate Index Search SET Counter MemoryHR-J745EK only Activate SpatializerSpatializer Soundtrack Selection HR-J745EK onlyActivate Scene Finder Stop Scene FinderActivate Repeat Basic Recording Recording Features Screen Access Main MenuS.T. Picture System Return to NormalPlayback CordVideo Plus+ Timer Recording PDC RecordingIf your recorder receives Press OK after enteringEnter Programme Regular Timer ProgrammingAccess Programme Start TimeEnter Preset Position Return to Normal ScreenPress TV PROG. + Revise Programme Check And Cancel ProgrammesTimer Warning InformationAuto Timer Access Main Menu ScreenTimer Auto SP/LP TimerMake Connections SET Recording DECK’S Input ModeEdit To Or From Another Video Recorder Start Source PlayerRecorder Player PlayerRecorder Your recorderStart Camcorder Edit From a CamcorderSET RECORDER’S Input Start RecorderConnection To Stereo System HR- J745EK only Connection To a Satellite Receiver Satellite Receiver UnitBack of HR-J745EK Pin Scart connectors Aerial terminal On-Screen Dispiay ENABLE/DISABLE ON-SCREEN DisplayTurn on the Recorder Press Push JOG %ÞtoSET A/B Code Switch RE-SUPPLY PowerSET TV Brand Code TV Multi-brand Remote ControlControl Your TV Using Additional Buttons TRY Operating TVSatellite Receiver Multi Brand Remote Control SET Satellite Receiver Brand CodeTRY Operating Satellite Receiver Auto Channel Set Perform Auto Channel SETStations your recorder Preset positions PRProcedures Located appear on aSelect Position Access ConfirmationManual Channel Set Input ChannelClose Confirmation Select ItemDelete Channel Select NEW PositionSelect Station Name Character Switch StationsSelect NEW Station Enter NEW CharacterSelect Channel to Perform TuningFine-Tuning Channels Already Stored FINE-TUNETV Station And ID List Station NameTV Station Channel Number Guide ScotlandClock Set Turn the Recorder onPreparation SET Date and Time PresetSET Clock SET Just ClockTroubleshooting Timer Recording Timer againQuestions and Answers Specifications Index Rear View J745EK Display Panel J745EK Display Panel J249EK Remote Control Installing Batteries How To UseEMO Memo Victor Company of JAPAN, Limited