JVC HR-J658E, HR-J700E Video Channel Set, Access Video Channel SET Mode, SET Video Channel

Page 37

SUBSIDIARYSETTINGSEN37

Video Channel Set

Video Channel (RF Output Channel) is the channel on which your TV receives picture and sound signals from the video recorder through the RF cable.

IMPORTANT

Perform the following steps only if —

—Video Channel Set has not been done correctly by the Auto Set Up function (☞ pg. 4).

—interference appears in the TV picture after you have moved to a different area or a new station has started broadcasting in your area.

—you change the connection between your recorder and TV from RF connection to AV connection, or vice versa.

If you have connected the video recorder to your TV via both the RF cable and a 21-pin SCART cable (AV connec- tion), since you do not need the video channel you have to set the video channel to off.

If you have connected the video recorder to your TV via the RF cable only (RF connection), you have to set the correct video channel.

Before performing the following steps, make sure the recorder's power is off and there is no cassette inserted in the recorder.

1

2

ACCESS VIDEO CHANNEL SET MODE

Hold down STOP (5/8) on the recorder until the display panel shows the following.

SET VIDEO CHANNEL

With AV Connection

Press TV PROG – until the display panel shows "–OUT– –".

●Now the video channel is set to off.

With RF Connection

Press TV PROG + or – to set the video recorder to a vacant channel between 22 and 69 which is not occupied by any local station in your area.

(Ex.) If channel 50 is available in your area

Then set your TV to UHF channel 50.

●If the two vertical white bars appear clearly on the screen as shown to the right, go to step 3.

●If the two vertical white bars do not appear clearly, re-set the video recorder to another vacant channel and try again.

NOTES:

●If you set the video recorder to a channel which is occupied by a local station or has neighbouring channels that are occupied by local stations, the picture reception quality will be affected and some interference noise will appear on the TV screen. Be sure to select a vacant channel which has no broadcast on neighbouring channels.

●If you cannot obtain the two vertical white bars clearly with any channel between 22 and 69, consult your JVC dealer.

EXIT VIDEO CHANNEL SET MODE

3 Press OK on the remote control.

With AV Connection:

To view picture signals from the video recorder, set your TV to its AV mode.

With RF Connection:

The channel on which the screen in step 2 appears clearly is your video channel.

To view picture signals from the video recorder, set your TV to the Video Channel.

Page 36 Page 38
Image 37
Page 36 Page 38
Contents HR-J700E HR-J658E/EH For Italy Safety PrecautionsDo not place the recorder Basic Connections Check ContentsSituate Recorder Connect Recorder to MainsIf you are referring to the front display panel Auto Set UpIf you are referring to the on-screen display International Telephone Country CodeVia an RF cable only RF connection Language CodeVideo Channel Your TV to the Video Channel. Refer toLanguage for the on-screen display If both auto channel set and auto clock set have failedJust Clock Just Clock onLanguage ENABLE/DISABLE ON-SCREEN Display Access Main Menu ScreenOn-Screen Displays Return to Normal ScreenPower Save Mode About Ntsc Playback Colour System SetColour Load a Cassette Basic PlaybackPoint Start PlaybackPlayback Playback FeaturesSearch Activate HIGH-SPEED SearchOverride Automatic Tracking Adjust TrackingManually Return to AutomaticSoundtrack Selection Repeat PlaybackDuring Playback Track USEBasic Recording Recording Features To Record Stereo And Bilingual Programmes A2 Receiving Stereo Bilingual ProgrammesType of Broadcast On-screen Display Being Received Mode SET, then press Select B.E.S.T. ModeS.T. Picture System PreparationPlayback RecordingOr press Record on the recorder During B.E.S.TTimer Programming Satellite Tuner Users Timer WarningStart Time Express Timer ProgrammingEnter Programme Stop TimeTimer Mode SET VPS/PDC ModeEngage RECORDER’S VPS/PDC RecordingCheck, Cancel And Replace Programmes Auto Timer Auto SP→LP TimerAutomatic Satellite Programme Recording Prog REC ModeBefore performing the following steps Remove Power Supply Remote Control FunctionsSET Remote Control Code RE-SUPPLY PowerSET TV Brand Code TV/VCR, TV +/- VolumeOperate TV TV Prog +Operate Satellite Tuner Satellite Tuner Multi-Brand Remote ControlBefore you start Satellite Tuner Brand CodeEdit To Or From Another Video Recorder SET Recording DECK’S Input ModeMake Connections Start Source PlayerPlayer AV2 Select SettingRecorder Recorder PlayerSET RECORDER’S Input Edit From a CamcorderMode Start CamcorderSelect Input Mode Connecting Using a DecoderConnect Decoder SET TunerSatellite Tuner Unit Connection To Satellite TunerBack of Recorder Back of TV AUX in or Tape Monitor Connecting Using a Stereo SystemExit Video Channel SET Mode Access Video Channel SET ModeVideo Channel Set SET Video ChannelAuto Channel Set Tuner SetView Confirmation Screen Perform Auto Channel SETStoring Channels Manually Enter NEW Channel InformationDelete a Channel When Receiving a Scrambled BroadcastChange Station Channel Position Switch Stations Access ManualChannel SET Screen Select NEW StationStation Name TV Station And ID ListFine-Tuning Channels Already Stored Perform TuningSelect Channel to FINE-TUNE Press OK twice. The Manual Channel Set screen appearsNumber Showview SetupEnter Receiving Channel Position Number Guide Program Number SetAccess Clock SET Screen Access Initial SET ScreenClock Set SET Date and TimeSET Clock Data Source Channel Position SET Just ClockStart Clock Operation Remote control wont function No power is applied to the recorderMains power cord is discon- nected If you’re using the RF OUT connec- tionTimer Recording Ä remain lit on the display panel. Is there Problem? Questions and AnswersIndex EN Index Remote Control IN/OUT x 1, IN/DECODER x Maximum recording timeFrequency synthesized tuner Memo International Telephone Language Code Ex. Francais is selected for BelgiumFor More Information see INSTRUCTIONS/P4

HR-J658EH, HR-J658E, HR-J700E specifications

The JVC HR-J700E, HR-J658E, and HR-J658EH are notable models in JVC's range of VHS VCRs that emerged during the height of VHS technology. Each of these models comes with impressive features and characteristics, catering to varied user needs and preferences.

The JVC HR-J700E is renowned for its advanced capabilities, including a 4-head system that enhances video playback quality. This model supports SP, LP, and SLP recording modes, allowing for flexible tape management. Notable features include an Auto Tracking function that ensures optimal tape alignment, reducing distortion during playback. The HR-J700E also integrates a digital noise reduction system, improving picture quality by minimizing unwanted artifacts. The video output is complemented by a set of audio outputs, including stereo, ensuring a richer sound experience.

The HR-J658E model offers a blend of performance and user-friendliness. This device shares many of the features of the HR-J700E, including the 4-head system and multi-speed recording capabilities. It features a simpler user interface, making it suitable for users who prefer straightforward operation without sacrificing quality. Additionally, the tape counter and clock features on this device make it easier to track recordings, while its external connections allow for easy integration with modern televisions and audio systems.

Meanwhile, the HR-J658EH is an enhanced version of the HR-J658E, which comes with more advanced functionalities. This model maintains the core features of its predecessor while introducing features like a built-in tuner. This allows for direct reception of television signals, making it convenient for recording live broadcasts without additional hardware. The HR-J658EH continues to focus on user experience with its programmable timer settings, enabling users to schedule recordings ahead of time, a crucial aspect for those who wish to record their favorite shows while away.

All three models boast robust build quality, with a design that reflects the era's style while ensuring longevity. They also incorporate JVC's commitment to quality, characterizing each unit with minimal tape wear, thanks to their well-engineered mechanisms. While VHS technology has largely been replaced by digital formats, the HR-J700E, HR-J658E, and HR-J658EH remain relevant for collectors, antique enthusiasts, and users who appreciate the analog format's warmth. With their features and user-oriented designs, these VCRs continue to hold a nostalgic pull for many users worldwide.
Top Page Image Contents