JVC HR-S3800U manual Basic Playback Features, 22 EN, Changing display information

Page 22

22 EN

BASIC PLAYBACK AND RECORDING (cont.)

Basic

Playback

Features

A Changing display information

Press DISPLAY during playback.

Each time you press the button, the front display panel shows the time counter, tape remaining time and the clock time in sequence.

Time Counter			Tape Remaining Time
Time Counter			Tape Remaining Time

POWER

S-VIDEO

VIDEO (MONO)L—AUDIO—R

S-VHS ET	SP	EP
S-VHS ET		VCR

	STOP/EJECT
	( 7/ 0)
	REW	FF
	MENU
CH	REC	STOP/EJECT PAUSE
	OK

Clock Time

c To display the VCR status including the time counter and the clock time on the TV screen, see “Showing on- screen display” (Z pg. 27).

c "COUNT" appears on the screen when the time counter is shown. "REMAIN" appears on the screen when the tape remaining time is shown.

c The approximate tape remaining time appears and the "" indicator lights on the front display panel.

D –1, 2, 3

F –b

c The tape remaining time is calculated based on the tape speed (SP or EP) being used. The indicated remaining time is only an estimate.

To reset the time counter, press C. RESET on the

Remote. The counter reading becomes “0:00:00”. It is also reset when a tape is inserted.

Checking tape position

E	1	2
	1	2
	4	5
	7	8
C. RESET		0

1

A

3

2

6

9

F –C

D –2

B

The tape position indicator
appears on screen in the
following cases:
c When you change the VCR
operation mode from the	B	+ + +		E
operation mode from the	B	+ + +		E
stop mode to fast forward or
rewind mode.		COUNT	0:33:27
c When you perform an Index

Search (Z pg. 24) or Instant Review (Z pg. 24).

The position of “ ” in relation to “B” (Beginning) or “E” (End) shows you where you are on the tape.

F –a, b, c

C

F –aSTOP ( 7 )

NOTES:

c "SUPERIMPOSE" must be set to “ON”, or the indicator will not appear (Z pg. 38, 39).

c It may take a few seconds for the tape position indicator to be displayed.

C Playing back tape repeatedly

—Repeat Play

You can play back a tape repeatedly (100 times).

While playing back a tape, press and hold PLAY ( 3) for more than 5 seconds.

The play indicator ( # ) on the front display panel starts flashing slowly, and a tape will be played back 100 times.

To stop playback, press STOP ( 7) on the Remote or STOP/EJECT ( 7 / 0) on the front panel.

HR-S4800U/S3800U-EN21-29

22

00.1.31, 9:57 AM

Image 22

Contents HR-S4800U HR-S3800U Dear Customer TelephoneNumberPower Lines Power SourcesPower Cord Protection Grounding or PolarizationCleaning AccessoriesDamage Requiring Service Replacement PartsContents Basic Connections Back of VCRSituate VCR Check contents Final preparation for useConnect VCR to power source Connect VCR to TVWhat to do if Plug & Play setting failed Plug & Play SettingPerform Plug & Play setup Clock and tuner channels will be set automaticallyAccess Initial Set screen Language SettingAccess Main Menu screen Select languagePreparations Clock Setting10 EN Select clock setSet Auto Clock to on Setting clock semiautomaticallySelect D.S.T. mode Select time zoneSetting clock manually 12 ENAccess Tuner Set screen Tuner SettingPerform Auto Channel Set 14 EN Setting channels manuallyAccess Manual Channel Set screen Manual Channel SetAttach Controller Cable Box Control SettingSituate Controller Connect cable box to VCR16 EN Access Main Menu screen on VCRAccess Cable Box Set screen Turn on cable boxAccess Cable Box Brand Set screen Enter cable box brand18 EN How to control the DBS receiverConnect DBS receiver to VCR Turn on DBS receiver Access DBS Receiver Set screen Access Main Menu screen on VCR Select DBS receiver output channelEnter DBS Receiver’s brand Access DBS Receiver Brand Set screen20 EN If the DBS receiverÕs channel does not change asshownaboveBasic Playback Load a cassetteChanging display information Basic Playback Features22 EN Checking tape positionSelecting monitor sound Adjusting tracking conditionAutomatic operations after 24 EN Locating beginning of timerAccess distant code Locating beginningSet tape speed Basic RecordingSelect recording channel Start recordingSpecifying recording length Basic Recording Features26 EN Watching one program while recording anotherDisplay VCR status on TV screen Select S-VHS ET modeShowing on-screen display Exit on-screen displayLocating particular scene Special Effect Playback28 EN Rapidly Picture Search High-Speed Picture SearchViewingframe still picture frame by Viewing still pictureSkipping unwanted portions Viewing slow motion picture30 EN VCR Plus+ Timer ProgramingAccess VCR Plus+ screen Enter PlusCode numberInput receiving channel number To use the VCR while it is in timer recording standby modeEngage timer recording standby mode Check program date32 EN Changing VCR Plus+ SettingVCR Plus+ guide channel matching To Guide Channel Access Guide Channel Set screenInput guide channel number To move the highlight bar arrow to GuideSet program stop time Express Timer Programing34 EN Set program dateEngage timer recording standby mode To timer-record daily Monday-Friday or weekly serialsChecking program settings 36 ENOverlapping programs blink on the screen Confirm overlapping programsSelect program to modify Press Shuttle Plus %Þ, then press Shuttle Plus #38 EN Useful Function SettingsChange setting Select FunctionPicture Control Auto TimerVideo Calibration SuperimposeVideo Stabilizer Auto SP = EP Timer40 EN Blue BackVHS Mode AV COMPU-LINKRear AUX Input 42 ENFront AUX Input Edit FunctionChild Lock Cannot turn on the VCR by pressing Power onChild lock function is now activated and you Connection Edit From Camcorder44 EN Various connection for editing tapesSet AV COMPU-LINK to OFF Select input mode on this VCRMake connections Start playbackEdit To Or From Another Select edit modeSelect input mode on recording VCR 46 ENSet Edit Function to A. DUB Source Select input modeAudio Dubbing Locate start pointAnother VCR for playback 48 ENInsert Editing Sourcetape Editedtape AV Dubbing Sourcetape EditedtapeSelect editing function you want Activate editing modePrepare tapes Start editingTurn on the TV TV Brand Setting50 EN Set TV brand codeEnter cable box brand code Cable Box Brand SettingTurn on the cable box Operate cable boxTurn on the DBS receiver DBS Receiver Brand Setting52 EN Enter DBS receiver brand codeUnplug VCR Changing Remote Control CodeSet remote control code for Remote Plug in VCRTroubleshooting 54 ENTimer Recording Other Problems 56 ENCan the VCR indefinitely remain in the recording pausemode? Can the VCR indefinitely remain in still mode?What happens if the tape reaches its end during recording? Brand Installing the Controller 18 Output channel Brand Installing the Controller 15 Output channelManual setting Preparation Semiauto setting 58 ENFront panel Front display panelRear panel 60 ENOn-screen display How to use the Remote Remote62 EN UsablecassettesHOW to Locate Your JVC Service Center Limited Warranty 64 ENMemo 66 EN HR-S4800U/S3800U-EN54-68 00.1.31, 1005 AM HR-S4800U/S3800U

Related manuals

Manual 2 pages 57.65 Kb