JVC HR-S3901, HR-3911U specifications Declaration of Conformity

Page 2

CAUTION:

Changes or modifications not approved by JVC could void user’s authority to operate the equipment.

Declaration of Conformity

Model Number:

HR-S3901/3911U

Trade Name:

JVC

Responsible Party:

JVC Americas Corp.

Address:

1700 Valley Road Wayne, N.J. 07470

Telephone Number:

973-317-5000

This device complies with Part 15 of FCC Rules. Operation is subject to the following two conditions:

(1)This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Failure to heed the following precautions may result in damage to the VCR, Remote or video cassette.

1.DO NOT place the VCR . . .

...in an environment prone to extreme temperatures or humidity.

...in direct sunlight.

...in a dusty environment.

...in an environment where strong magnetic fields are generated.

...on a surface that is unstable or subject to vibration.

2.DO NOT block the VCR’s ventilation openings.

3.DO NOT place heavy objects on the VCR or on the Remote.

4.DO NOT place anything which might spill on the top of the VCR or on the Remote.

5.AVOID violent shocks to the VCR during transport.

VCR Plus+, C3 and PlusCode are registered trademarks of Gemstar Development Corporation.

The VCR Plus+ system is manufactured under license from Gemstar Development Corporation.

For Customer Use:

Enter below the Model No. and Serial No. which are located on the rear of cabinet. Retain this information for future reference.

Model No.

Serial No.

Cassettes marked “S-VHS” and “VHS” can be used with this video cassette recorder. However, S-VHS recordings are possible only with cassettes marked “S-VHS”.

By using S-VHS ET it is possible to record and play back with S-VHS picture quality on VHS cassettes with this VCR.

As an ENERGY STAR® Partner, JVC has determined that this product or product model meets the ENERGY STAR® guidelines for energy efficiency.

IMPORTANT PRODUCT SAFETY INSTRUCTIONS

Electrical energy can perform many useful functions. But improper use can result in potential electrical shock or fire hazards. This product has been engineered and manufactured to assure your personal safety. In order not to defeat the built-in safeguards, observe the following basic rules for its installation, use and servicing.

ATTENTION:

Follow and obey all warnings and instructions marked on your product and its operating instructions. For your safety, please read all the safety and operating instructions before you operate this product and keep this booklet for future reference.

INSTALLATION

1. Grounding or Polarization

(A)Your product may be equipped with a polarized alternating- current line plug (a plug having one blade wider than the other). This plug will fit into the power outlet only one way. This is a safety feature.

If you are unable to insert the plug fully into the outlet, try reversing the plug. If the plug should still fail to fit, contact your electrician to replace your obsolete outlet. Do not defeat the safety purpose of the polarized plug.

(B)Your product may be equipped with a 3-wire grounding-type plug, a plug having a third (grounding) pin. This plug will only fit into a grounding-type power outlet. This is a safety feature. If you are unable to insert the plug into the outlet, contact your

electrician to replace your obsolete outlet. Do not defeat the safety purpose of the grounding-type plug.

2. Power Sources

Operate your product only from the type of power source indicated on the marking label. If you are not sure of the type of power supply to your home, consult your product dealer or local power company. If your product is intended to operate from battery power, or other sources, refer to the operating instructions.

3. Overloading

Do not overload wall outlets, extension cords, or integral convenience receptacles as this can result in a risk of fire or electric shock.

4. Power Cord Protection

Power supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them, paying particular attention to cords at plugs, convenience receptacles, and the point where they exit from the product.

5. Ventilation

Slots and openings in the cabinet are provided for ventilation. To ensure reliable operation of the product and to protect it from overheating, these openings must not be blocked or covered.

Do not block the openings by placing the product on a bed, sofa, rug or other similar surface.

Do not place the product in a built-in installation such as a bookcase or rack unless proper ventilation is provided or the

manufacturer’s instructions have been adhered to.

6. Wall or Ceiling Mounting

The product should be mounted to a wall or ceiling only as recommended by the manufacturer.

ANTENNA INSTALLATION INSTRUCTIONS

1. Outdoor Antenna Grounding

If an outside antenna or cable system is connected to the product, be sure the antenna or cable system is grounded so as to provide some protection against voltage surges and built-up static charges. Article 810 of the National Electrical Code, ANSI/NFPA 70, provides information with regard to proper grounding of the mast and supporting structure, grounding of the lead-in wire to an antenna discharge unit, size of grounding connectors, location of antenna discharge unit, connection to grounding electrodes, and requirements for the grounding electrode.

— 2 —

Image 2
Contents Contents Declaration of Conformity How to use the Remote Video heads cleaningRear Panel Buttons, Connectors and IndicatorsRemote Front Panel On-screen displayAV Connection Connections and Plug&Play SettingRF Connection Video ConnectionClock Setting Initial SettingsLanguage Setting Setting channels automatically Auto Channel Set Tuner SettingCable Box and/or DBS Receiver Control Setting Setting channels manually Manual Channel SetConnect Controller to VCR Access Cable Box Set screen or DBS Receiver Set screenAccess Brand Set screen Turn on cable box or DBS receiverPlayback Playback FeaturesAdjusting tracking condition Tracking Adjustment Basic PlaybackPlaying back tape repeatedly 100 times Repeat Play Locating beginning of timer recordings Instant ReviewAutomatic operations after rewinding Next Function Memory Locating beginning of recordings Index SearchBasic Recording Recording FeaturesRecording VCR Plus+ Timer Programing Timer RecordingChanging VCR Plus+ Setting 24HR Quick Programing Express Timer ProgramingTo use the VCR while it is in timer recording standby mode Other Functions Timer warning displayFunction settings Checking tape positionEP mode When this function is set to onWhen this function is set to OFF Press Play 4 to start recordingSatellite Auto Recording Child LockTV Brand Setting Multi-Brand Remote ControlChanging Remote Control Code Cable Box or DBS Receiver Brand SettingEditing VHF SpecificationsVHS UHFTroubleshooting For Servicing Only in U.S.A %3!#%43!##!3*%!%6%43!##!3*%!%6*$!#8*!G Warranty Only in U.S.A75!48*35*6!445* %#* =51!!%3?*6@A #73*%*#4!%68!#&46&3*#%* 4&GMemo KCC