JVC HR-5910U, HR-S5900U manual Cable Box Control Setting, Situate Controller, Attach Controller

Page 15
Controller (suggested locations)
Cable box

EN 15

Cable Box

Control

Setting

Suggested location

Place the cable box on top of the VCR. Attach the VCR’s Controller to the top of the VCR with the Controller’s transmitter pointed towards the cable box’s remote sensor.

ATTENTION:

The Controller can also control a DBS receiver. If both a cable box and a DBS receiver are used, position the Controller so its signal reaches the remote sensors on both the cable box and DBS receiver.

Your VCR

Cable box

To

To

RF output

Audio/Video

Controller

output

Transmitter

 

 

or

To

To

ANTENNA

AUDIO/

IN

VIDEO IN

Your VCR

CABLE

BOX

The following procedure is required if you receive your TV channels through a cable box (descrambler). The Controller allows the VCR to automatically switch the cable box channel during timer recording. The Controller is effective for recording broadcasts that have been programmed using VCR Plus+ ( pg. 30), Express timer programing ( pg. 34) or 24HR quick programing ( pg. 36).

NOTE:

The Controller is not supplied with this unit. It can be requested by mailing in the completed JVC Cable Mouse Certificate that is included with the accessory package.

1Installing Controller

Situate Controller

Place the Controller so that its transmitter is facing the cable box’s remote sensor.

●Make sure the path between the Controller and

2the cable box’s remote sensor is not blocked.

Attach Controller

Fix securely using the adhesive strip attached on

3the back of the Controller.

Connect cable box to VCR

●If your cable box does not have audio/video output connectors

Connect the RF output terminal on the cable box to the ANTENNA IN terminal on the rear of your VCR.

●If your cable box has audio/video output connectors

Connect an audio/video cable between the AUDIO/VIDEO IN connectors on the rear of the VCR and the audio/video output connectors on the cable box.

NOTE:

When connecting your cable box, refer to its instruction

4manual.

Connect Controller to VCR

Connect the Controller to the CABLE BOX

Controller connector on the rear panel.

How to control the cable box

This VCR has two separate methods to control your cable box.

●The VCR’s wireless Remote can control your cable box. This eliminates the need for a separate cable box’s Remote.

●The VCR’s Controller can also control your cable box. This allows the VCR to change your cable box’s channel number during timer recording.

Each method must be set up separately. To set up the VCR’s Remote, refer to page 53. To set up the Controller, go to page 16.

Page 14 Page 16
Image 15
Page 14 Page 16
Contents
HR-S5900U/5910U HR-S3900U/3910U Address Dear CustomerGrounding or Polarization Power SourcesPower Lines Power Cord ProtectionReplacement Parts AccessoriesDamage Requiring Service CleaningContents Back of VCR Basic ConnectionsConnect VCR to TV Check contentsConnect VCR to power source Situate VCRClock and tuner channels will be set automatically Plug & Play SettingPerform Plug & Play setup What to do if Plug & Play setting failedSelect language Language SettingAccess Main Menu screen Access Initial Set screenSelect clock set Clock Setting10 EN 1Preparations Select host channel Setting clock semiautomatically Select D.S.T. mode Set Auto Clock to on12 EN Setting clock manuallyAutomatically Auto Channel Set Tuner SettingAccess Tuner Set screen Perform Auto Channel SetShuttle Plus # to Access Manual Channel Set screenAdd or skip desired channels Manual Channel SetConnect cable box to VCR Cable Box Control SettingSituate Controller Attach ControllerCable BOX SET Access Cable Box Set screenSelect cable box output channel Turn on cable boxIf the cable boxs channel does not change to Access Cable Box Brand Set screenEnter cable box brand Press OKDBS receiver Controller Your VCRsuggested Locations How to control the DBS receiver18 EN Connect DBS receiver to VCRSelect DBS receiver output channel Access Main Menu screen on VCRAccess DBS Receiver Set screen Turn on DBS receiverIf the DBS receiver’s Access DBS Receiver Brand Set screenChannel listed below for your brand, setting is complete Enter DBS Receiver’s brandStart playback BasicPlayback Load a cassetteChecking tape position Basic Playback Features22 EN Changing display informationActivate manual tracking Adjusting tracking conditionSelecting monitor sound Automatic operations afterLocating beginning Locating beginning of timerAccess distant code 24 ENStart recording Basic RecordingSelect recording channel Set tape speedWatching one program while Basic Recording Features26 EN Specifying recording lengthExit on-screen display Select S-VHS ET modeShowing on-screen display Display VCR status on TV screenRapidly Picture Search High-Speed Picture Search Special Effect Playback28 EN Locating particular sceneViewing still picture Skipping unwanted portionsViewing slow motion picture Enter PlusCode number VCR Plus+ Timer ProgramingAccess PlusCode No. screen 30 ENCheck program date Engage timer recording standby modeTo use the VCR while it is in timer recording standby mode Input receiving channel numberChanging VCR Plus+ 32 ENVCR Plus+ guide channel matching SET, then press OK or Access Main Menu screen Input receiving channel numberInput guide channel number Guide Channel34 EN Express Timer ProgramingTo timer-record daily Monday-Friday or weekly serials 36 EN Access 24HR quick program displayTimer warning display 24HR Quick ProgramingChecking program settings Program Completed appears on the screen for about 38 ENConfirm overlapping programs Select program to modifySelect Function Useful Function SettingsAccess Function Set screen Change settingWhen this function is set to on When this function is set to OFF40 EN For Example By selecting either HI-FI L or HI-FI R Mode is used for recording on S-VHS tapesBy connecting other JVC’s AV Compulink components see AV Compulink connectors becomes possibleThis function is only for HR-S5900U/5910U AV Compu LinkPress REC Link Set timer program on DBS receiverEngage Satellite Auto Recording standby mode 44 ENChild Lock Various connection for editing tapes Edit From Camcorder46 EN ConnectionSet Picture Control to Edit Select input mode on this VCRMake connections Select video input terminal48 EN Edit To Or From AnotherStart audio dubbing Activate editing modeAudio Dubbing 1Locate start pointAV Dubbing Source tape Edited tape 50 ENAnother VCR for playback Insert Editing Source tape Edited tape1Locate end point Prepare tapesLocate start point Start editingSet TV brand code TV Brand Setting52 EN Turn on the TVOperate cable box Cable Box Brand SettingTurn on the cable box Enter cable box brand codeEnter DBS receiver brand code DBS Receiver Brand Setting54 EN Turn on the DBS receiverRemote Control ChangingCode 56 EN TroubleshootingTimer Recording Moisture Condensation 58 ENRecording Timer RecordingPlayback Can the VCR indefinitely remain in still mode?List of terms 60 EN12POWER button  pg REC ¶ button  pgSP/EP button only for HR-S3900U/3910U Only for HR-S5900U/5910U 62 EN7S Video OUT connector  pg Rear panel1On-screen display 64 EN How to use the RemoteUsable cassettes 66 EN HOW to Locate Your JVC Service CenterLimited Warranty HR-S3900U/3910U
Top Page Image Contents