JVC HR-J443U instruction manual Important Product Safety Instructions

Page 3

IMPORTANT PRODUCT SAFETY INSTRUCTIONS

Electrical energy can perform many useful functions. But improper use can result in potential electrical shock or fire hazards. This product has been engineered and manufactured to assure your personal safety. In order not to defeat the built-in safeguards, observe the following basic rules for its installation, use and servicing.

ATTENTION:

Follow and obey all warnings and instructions marked on your product and its operating instructions. For your safety, please read all the safety and operating instructions before you operate this product and keep this booklet for future reference.

INSTALLATION

1. Grounding or Polarization

(A)Your product may be equipped with a polarized alternating- current line plug (a plug having one blade wider than the other). This plug will fit into the power outlet only one way. This is a safety feature.

If you are unable to insert the plug fully into the outlet, try reversing the plug. If the plug should still fail to fit, contact your electrician to replace your obsolete outlet. Do not defeat the safety purpose of the polarized plug.

(B)Your product may be equipped with a 3-wire grounding-type plug, a plug having a third (grounding) pin. This plug will only fit into a grounding-type power outlet. This is a safety feature.

If you are unable to insert the plug into the outlet, contact your electrician to replace your obsolete outlet. Do not defeat the safety purpose of the grounding-type plug.

2. Power Sources

Operate your product only from the type of power source indicated on the marking label. If you are not sure of the type of power supply to your home, consult your product dealer or local power company. If your product is intended to operate from battery power, or other sources, refer to the operating instructions.

3. Overloading

Do not overload wall outlets, extension cords, or integral convenience receptacles as this can result in a risk of fire or electric shock.

4. Power Cord Protection

Power supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against

EN3

5. Ventilation

Slots and openings in the cabinet are provided for ventilation. To ensure reliable operation of the product and to protect it from overheating, these openings must not be blocked or covered.

•Do not block the openings by placing the product on a bed, sofa, rug or other similar surface.

•Do not place the product in a built-in installation such as a bookcase or rack unless proper ventilation is provided or the manufacturer’s instructions have been adhered to.

6. Wall or Ceiling Mounting

The product should be mounted to a wall or ceiling only as recommended by the manufacturer.

ANTENNA INSTALLATION

INSTRUCTIONS

1. Outdoor Antenna Grounding

If an outside antenna or cable system is connected to the product, be sure the antenna or cable system is grounded so as to provide some protection against voltage surges and built-up static charges. Article 810 of the National Electrical Code, ANSI/NFPA 70, provides information with regard to proper grounding of the mast and supporting structure, grounding of the lead-in wire to an antenna discharge unit, size of grounding connectors, location of antenna discharge unit, connection to grounding electrodes, and requirements for the grounding electrode.

2. Lightning

For added protection for this product during a lightning storm, or when it is left unattended and unused for long periods of time, unplug it from the wall outlet and disconnect the antenna or cable system. This will prevent damage to the product due to lightning and power-line surges.

3. Power Lines

An outside antenna system should not be located in the vicinity of overhead power lines or other electric light or power circuits, or where it can fall into such power lines or circuits. When installing an outside antenna system, extreme care should be taken to keep from touching such power lines or circuits as contact with them might be fatal.

EXAMPLE OF ANTENNA GROUNDING AS PER

NATIONAL ELECTRICAL CODE, ANSI/NFPA 70

ANTENNA

LEAD IN WIRE

GROUND CLAMP

them, paying particular attention to cords at plugs, convenience receptacles, and the point where they exit from the product.

ELECTRIC SERVICE EQUIPMENT

ANTENNA DISCHARGE UNIT (NEC SECTION 810-20)

GROUNDING

CONDUCTORS

(NEC SECTION 810-21)

GROUND CLAMPS

POWER SERVICE GROUNDING ELECTRODE SYSTEM (NEC ART 250. PART H)

NEC – NATIONAL ELECTRICAL CODE

Page 2 Page 4
Image 3
Page 2 Page 4
Contents HR-J643U HR-J443U Do not place the VCR Dear CustomerImportant Product Safety Instructions Should be moved with care. Quick Product and cart combinationContents Basic Connections Auto Clock Set/Auto Tuner Set Plug & Play SetupInitial Settings Plug & PlayLanguage Auto Clock SET by ClockPreparation Arrow at the Custom Set Screen to OverrideSemi-Auto Select ModeAccess Select Screens Select Host ChannelManual Select D.S.T. ModeSelect Time Zone Make CorrectionsSET Access Main MenuAccess Tuner SET TunerInformation Store or Skip Desired Channel Access Tuner SET ScreenAccess AFC Screen Make SelectionStart Playback Simple PlaybackLoad a Cassette Find Program Start PointSimple Recording Playback Features RE-ENGAGE Automatic Tracking Engage Manual Tracking ModeAdjust Manual Tracking Layback and Recording FeaturesVideo Stabilizer Superimpose Access Function SETAccess Superimpose Return to NormalAccess Audio Monitor Select The Soundtrack HR-J643U OnlyMix Access Distant Code Start SearchSkip Over Unwanted Sections Activate Counter MemoryReturn to Counter Position Zero Access Main Menu Screen Access Video Calibration ScreenActive Video Calibration Playback RecordingSelect Channel for Viewing Recording FeaturesEngage TV Mode Reset Counter to ZeroTo Record Stereo Programs Access 2ND AudioStereo And SAP Second Audio Program HR-J643U Only To Record SAP Programs HR-J643U OnlyInformation On-Screen Timer ProgrammingAccess Program SET EN Timer RecordingPlus Þ%until the item you want to change begins Engage Timer ModePress just once to access the Auto Timer screen Press TIMER. The VCR turns off automaticallyCheck And Cancel Programs Disengage TimerCancel a Program RE-ENGAGE TimerAuto Timer Access Auto TimerPress REC on the front panel Instant Timer Recording ITREngage ITR Mode SET Recording DurationEdit To Another VCR Another VCR SET RECORDER’S Input ModeEdit From a Camcorder Or Another VCR PlayerSET TV Brand Code Special FeaturesTV Multi-Brand Remote Control Turn on the TVRemote Control DBS Receiver Multi-Brand Remote ControlCable Box Multi-Brand Turn VCR Power on Unplug Vcrs PowerSET Remote Control Plug in Power CordNected Record safety tab removedCassette gets stuck partway VCR have been incorrectly conTimer again Resume recordingSelect a different Host Channel during Playback EN Questions and AnswersMBR Multi-Brand Remote Code Setting IndexList Of Terms Front View HR-J443U has only one Audio input connectorRear View HR-J443U has only one Audio output connectorHow To Use Installing BatteriesSpecifications For Servicing Only in U.S.A HOW to Locate Your JVC Service CenterLimited Warranty Warranty Only in U.S.AHR-J643U/443U
Top Page Image Contents