JVC HR-V610AJ, HR-V610AA Satellite Auto Recording, Multi-Brand Remote Control, TV Brand Setting

– Other Functions –

AUTO SP]LP TIMER — ON / OFF

When this function is set to “ON”, the recorder automatically switches to LP mode to allow complete recording if there is not enough tape to record the entire program while timer-recording in SP mode.

For Example, Recording a PAL-broadcast programme of 210 minutes in length onto a 180-minute tape.

Approximately 150 minutes	Approximately 60 minutes
SP mode	LP mode

Total 210 minutes

NOTES:

●If you have programed the recorder to timer-record 2 or more programs, do not use this function, but change the tape speed manually during timer programing.

●There may be some noise and sound disturbance where the tape speed switches from SP to LP mode on the tape.

●The Auto SP]LP Timer feature is not available during ITR (Instant Timer Recording), and the feature will not work properly with any tapes longer than E-180 or with some tapes of shorter lengths.

Satellite Auto Recording

You can automatically record a satellite program which is timer- programed on your satellite receiver.

AConnect a satellite receiver to the AUDIO/VIDEO IN connectors on the rear panel. You can also connect the cable box if it has a timer.

BSet timer program on satellite receiver referring to its instruction manual.

CLoad a cassette with the record safety tab intact.

DPress SP/LP/EP (p) to set the tape speed.

EPress REC LINK for more than 2 seconds. The recorder turns off automatically and enter the Satellite Auto Recording standby mode (the REC LINK indicator lights up). When signals come into the recorder from the satellite receiver, the recorder starts recording (the REC LINK indicator blinks), and stops recording (the REC LINK indicator stops blinking) when signals stop coming in.

NOTES:

●Be sure not to turn on the satellite receiver before the program starts broadcasting; otherwise, the recorder will start recording when the satellite receiver is turned on.

●To disengage the Satellite Auto Recording standby mode, press REC LINK (the REC LINK indicator goes off).

●Depending on the type of satellite receiver, Satellite Auto Recording may not be compatible.

●B.E.S.T does not work when the satellite auto recording mode is engaged.

Multi-Brand Remote Control

This remote control can control some functions of remote controllable TVs, cable boxes, satellite receivers or DVD sets listed below. Without setting, you can control a JVC TV.

NOTES:

●Some unit’s brands have more than one code. If the unit does not function with a specified code, try other codes.

●Depending on the type of unit, some or all functions cannot be operated using this remote control.

●It’s not possible to operate a unit not equipped with a remote sensor.

●It’s not possible to set the remote control for two units at the same time.

●Once you have set the remote control to operate the unit, you do not have to set it until you replace the batteries from the remote control.

TV Brand Setting

ATurn on TV

Turn on the TV using the Power button on the TV or its remote control.

BSet TV brand code

APress and hold TV.

BPress the Number keys to enter your TV’s brand code. C Press OK, and release TV. The TV should turn off.

COperate TV

First, press TV to set the remote control to TV mode, then press one of the following buttons: 1, TV/VCR, TV PR+/–, ^ (TV Muting), TV %+/–, and the Number keys.

●For some brands, you must press ENTER after having pressed the Number keys to enter a channel number.

TV BRAND	CODE	TV BRAND	CODE
JVC	01, 23, 24, 25	MITSUBISHI	03
AIWA	36	MIVER	29
BEIJING	22	NEC	20
CCE	02	NOBLEX	22
CHANGHONG	34	NOKIA	31
DAEWOO	17, 37	PANASONIC	04, 11
FERGUSON	27	PEONY	34, 38, 39
FINLUX	30	PHILICO	10, 17, 21
FUNAI	32	PHILIPS	02, 42
GRADIENTE	15	SAMSUNG	12, 33, 34, 35
GRUNDIG	19	SANYO	13, 16
HITACHI	10	SHARP	06
ITT	28	SONY	07
JINXING	38	TCL	41
KONKA	40	THOMSON	26
LG/GOLDSTAR	18	TOSHIBA	08, 14

Cable Box, Satellite Receiver or DVD Brand Setting

ATurn on the unit

Turn on the cable box, satellite receiver or DVD using the Power button on the unit or its remote control.

BEnter brand code

APress and hold CABLE/SAT/DVD.

BPress the Number keys to enter your unit’s brand code. C Press OK, and release CABLE/SAT/DVD.

COperate the unit

First, press CABLE/SAT/DVD to set the remote control to cable box, satellite receiver or DVD mode, then press one of the following buttons:

For satellite receiver and cable box . . .

1, TV PR+/–,Number keys.

For DVD. . .

1, 4, 8, 9, 5, 3, w e (2 6) keys.

●For some brands, you must press ENTER after having pressed the Number keys to enter a channel number.

●To change the unit’s channels, press TV PR+/– or the Number keys. (The PR+/– button can be used to change the recorder’s channels only.)

— 11 —