
– Timer Recording –
Express Timer Programing
●Remember, the clock must be set before you can program the timer.
●Load a cassette with the record safety tab intact. The recorder turns on, and the counter is reset, automatically.
●Select the appropriate colour system with “PAL/MESECAM” and “NTSC” in Function settings.
Checking, cancelling or changing program settings
ADisengage timer
Press #, then press 1.
●When “AUTO TIMER” is set to “ON” ( 10), you do not have to press #.
BAccess Program Check screen
Press ".
CAccess Program screen
Press " again. Each time you press ", the next program’s Program screen appears.
PR START | STOP | CH | DATE | |
1 | 8:00 | 10:00 | 3 | 24.04 |
2 | 10:00 | 10:45 | 2 | 25.04 |
3 | 11:30 | 13:00 | 1 | 25.04 |
4 |
|
|
|
|
5 |
|
|
|
|
6 |
|
|
|
|
7 |
|
|
|
|
8 |
|
|
|
|
[ | ] : NEXT |
|
| |
| START | – P1 – | STOP |
|
|
|
| ||
| 8:00 |
| 10:00 |
|
|
|
| SP |
|
| DATE |
| TV PROG |
24.043
[ ] : NEXT
APress PROG on the remote control to access the
B Press START+/–, STOP+/–, DATE+/–
or PR+/– repeatedly to enter the start time, stop time, date or channel.
● Press and hold START+/– or
STOP+/– to increase the time in | DATE | TV PROG |
24.04 | 3 | |
| ||
● To set the tape speed, press SP/LP/ | [PROG] : EXIT |
|
|
| |
EP (p). |
|
|
●To
CPress OK or PROG.
●If “PROGRAM OVERLAPPED” appears, see “Program overlap warning display”.
DPress #. The recorder turns off automatically and “#” is displayed on the display panel.
To use the recorder while it is in timer recording standby mode
Press #, then press 1. After you use the recorder, press # again to put the recorder into timer recording standby mode.
DCancel or change program setting
To cancel a program, press & when the Program screen you do not want is shown.
To change a program, press the appropriate button:
EReturn to normal screen
Press " repeatedly until no Program screen is shown.
FReengage timer recording standby mode
Press #. The recorder turns off automatically and “#” is displayed on the display panel.
●When “AUTO TIMER” is set to “ON” ( 10), the timer recording standby mode automatically resumes when you turn off the recorder.
Program overlap warning display
If “PROGRAM OVERLAPPED” appears, you have another program overlapping the program you have just made. The Program Check screen appears and conflicting programs will start blinking.
| PR START | STOP | CH | DATE | ||||
PROGRAM OVERLAPPED | 1 | 8:00 | 10:00 | 3 | 24.04 |
| ||
2 | 10:00 | 10:45 | 2 | 25.04 |
| |||
| 3 | 11:30 | 13:00 | 1 | 25.04 |
| ||
| 4 | 9:00 | 10:00 | 92 | DAILY | |||
| 5 |
|
|
|
|
|
|
|
| 6 |
|
|
|
|
|
|
|
| 7 |
|
|
|
|
|
|
|
| 8 |
|
|
|
|
|
|
|
| [ | / ] |
|
| [PROG] : EXIT | |||
|
|
|
|
|
|
|
|
|
Example:
Program 1 (you have just made) and Program 4 overlap each other.
A Select program to modify
Press rt, then press e.
● You can only select one of the
overlapping programs. | 5 |
| |
● If you do not mind this overlap, press | 6 |
| |
7 |
| ||
PROG to finish the timer program | 8 |
| |
[ / ] | [PROG] : EXIT | ||
setting. The program starting earlier or | |||
|
|
program with the lower program number will be recorded.
B Cancel or change program setting– P1 –
To cancel a program, press & when the
Program screen you do not want is shown.
To change a program, press the appropriate button:
on which you want to make changes is shown, then press OK.
●If the overlap is not yet solved, the conflicting programs will be shown on the Program check screen. Repeat the above steps again.
— 9 —