JVC HR-V610AJ, HR-V610AA, HR-V610AG specifications Timer Recording, Guide Program Number Set

[0–9] OR [ / ] : SELECT

[PROG] : EXIT

Timer Recording

Up to 8 timer recording programs can be made using G-CODE/ SHOWVIEW timer programing (for HR-V610AG and HR-V610AJ only) or Express timer programing method as far as a year in advance. Remember, the clock must be set before you can program the timer.

NOTES:

●If all the 8 programs have already been set, “PROGRAM FULL” appears on the TV screen.

●After timer recording is completed, the recorder turns off automatically.

●You can program the timer recording while a regular recording is in progress; the menu screens will not be recorded.

●In case of a power failure after programming, the recorder’s memory backup keeps your selections (if the lithium battery is not exhausted).

●If the tape reaches its end during recording, the recording stops and “” and “ $” on the front display panel blink. Press 1 then 0 on the recorder to eject the cassette or press 3 on the remote control to rewind the tape.

G-CODE™/SHOWVIEW™System Setup

(For HR-V610AG and HR-V610AJ only)

INFORMATION

G-CODEand SHOWVIEW are different trademarks used to represent the same easy recording feature, but only the term G-CODEsystem will be used in the instructions. If you use the SHOWVIEW system, follow the same instructions listed for the G-CODEsystem.

The G-CODEtimer programming system eliminates the need to input channel, date, start and stop time data when setting the timer record function. Simply key in the G-CODEnumber for the TV programme you wish to record (found in most TV listings) and the recorder's timer is automatically programmed.

You have to set “GUIDE PROG” numbers, which are assigned to each station for purposes of G-CODEtimer programming, for all the stations stored in your recorder’s memory to get proper results.

Before G-CODEsetup you must have performed the procedures of Tuner Set and Clock Set.

IMPORTANT

Perform the following procedure after Auto Set Up and/or the channel setting steps.

After setting the Guide Program Numbers, channel positions may be incorrect if you stored or skipped channels. In this case, re- perform Guide Program Number setting.

Guide Program Number Set

AAccess Main Menu screen, then Initial Set screen

Press MENU on the remote control. Press rt to place the pointer next to “INITIAL SET”, then press OK or e.

BAccess G-CODE/SHOWVIEWSetup screen

Press rt to place the pointer next to “G-CODE/SHOWVIEW SETUP”, then press OK or e.

C Input Guide Prog number	G-CODE/SHOWVIEW SETUP
Press rt or the Number keys to select	GUIDE PROG	TV PROG
the Guide Program number as shown in
	2	5
the TV listing, then press OK or e.
	[0–9] OR [ /	] : SELECT
	[MENU] : EXIT
D Input receiving channel number	G-CODE/SHOWVIEW SETUP
Press rt or the Number keys to select	GUIDE PROG	TV PROG
the number of the channel on which the
	2	5
Guide Program number’s broadcasts are
received, then press OK or e.	[0–9] OR [ /	] : SELECT

[MENU] : EXIT

●If the satellite broadcast is received on your recorder's auxiliary channel (“L-1” or “F-1”), select “L-1” or “F-1” for the channel position to which the satellite receiver is connected.

●Repeat steps 3 and 4 as necessary.

EReturn to normal screen

Press MENU on the remote control.

G-CODE™/SHOWVIEW™Timer Programing

(For HR-V610AG and HR-V610AJ only)

The G-CODEnumbers are the numbers next to the program in most TV listing. ● Remember, the clock must be set

before you can program the timer. ● Be sure to read “G-CODE™/

SHOWVIEW™ System Setup”.

● Load a cassette with the record safety tab intact. The recorder turns on, and the counter is reset, automatically.

● Select the appropriate colour system with “PAL/MESECAM” and “NTSC” in Function settings.

A Press PROG on the remote control to access the G-CODE/SHOWVIEWscreen.

G-CODE/SHOWVIEW NO.

[0 – 9]

[+/–] : EXPRESS PROGRAMING

[PROG] : EXIT

BPress the appropriate Number keys to input the G-CODEnumber, then press OK. Check to make sure the setting is accurate on the G-CODEProgram screen.

	G-CODE/SHOWVIEW NO.					– P1 –
					NO. 12345678
		1 2 3 4 5 6 7 8		START				STOP
			21:00					22:00
								SP
				DATE				TV	PROG
	[0 – 9]
	[ ] : DELETE			25.04					1
	[PROG] : EXIT			: [OK]
● If the G-CODE/SHOWVIEWSetup								G-CODE/SHOWVIEW SETUP
	screen appears after pressing OK,
	press the Number keys, PR+/– or						GUIDE PROG				TV PROG
					2					5

rt to input the number of the channel on which the broadcast for the G-CODEnumber is received on the recorder, then press OK.

●To set the tape speed, press SP/LP/EP (p).

●To change the stop time, press STOP+/–.

●To timer-record daily (Monday–Friday) or weekly serials, press DAILY (number key 8) or WEEKLY (number key 9). Pressing the button again makes the “DAILY” or “WEEKLY” display disappear.

●If you made a mistake, press & to access the G-CODE/ SHOWVIEW screen again.

●If an incorrect G-CODE/SHOWVIEWnumber or the one for a broadcast already finished has been input, “ERROR” is displayed for about 5 seconds, then the G-CODE/SHOWVIEWscreen reappears.

CPress OK or PROG.

●If “PROGRAM OVERLAPPED” appears, see “Program overlap warning display” ( 9).

DPress #. The recorder turns off automatically and “#” is displayed on the display panel.

— 8 —