JVC HR-J280, HR-J289EU, HR-J281 specifications Other Problems

Page 49

			EN 49
OTHER PROBLEMS
	SYMPTOM	POSSIBLE CAUSE	CORRECTIVE ACTION
1.	Whistling or howling is heard from the	● The camcorder’s microphone is too	Position the camcorder so its microphone
	TV during camcorder recording.	close to the TV.	is away from the TV.
		● The TV’s volume is too high.	Turn the TV’s volume down.

2.	When scanning channels, some of	● Those channels have been designated to	If you need the skipped channels, restore
	them are skipped over.	be skipped.	them ( pg. 40).

3.	The channel cannot be changed.	● Recording is in progress.	Press 9 to pause the recording, change
			channels, then press 4 to resume
			recording.

4.	Channel settings that were made	● After the manual settings were made,	Perform manual setting again.
	manually seem to have changed or	Auto Channel Set was performed.
	disappeared.

5.	No channels are stored in the	● The TV aerial cable was not connected	Turn off the recorder once and connect
	recorder’s memory.	to the recorder when Auto Set Up was	the TV aerial cable to the recorder
		performed.	properly, then turn on the recorder again.
			Then perform Auto Set Up again
			( pg. 8).
		● The fully-wired 21-pin SCART cable was	Turn off the recorder once and connect
		not connected between TV and the	the fully-wired 21-pin SCART cable to the
		recorder when Preset Download was	recorder properly, then turn on the
		performed.	recorder again. Then perform Preset
			Download again ( pg. 10).

ATTENTION

This recorder contains microcomputers. External electronic noise or interference could cause malfunctioning. In such cases, switch the recorder off and unplug the mains power cord. Then plug it in again and turn the recorder on. Take out the cassette. After checking the cassette, operate the unit as usual.

Image 49

Contents Video Cassette Recorder English Safety Precautions Moisture Condensation Front View Front Display Panel ON-SCREEN Display Operating JVC TVs How To UseSituate the recorder Check the contentsConnect the recorder to TV Connect the recorder to mainsTurn on the recorder Auto Set UpSelect your country Before starting, make sure of the followingSelect the language Perform Auto Set UpOn the front display panel On the on-screen display10 EN Perform Preset DownloadSet the video channel Press rt to select CH - and press OK or eJust Clock Language for the on-screen displayAccess the Country Set screen Access the Main Menu screenLanguage 12 ENLink Functions NexTView Link TV Auto Power OnVCR Auto Standby Direct Rec14 EN Basic PlaybackHigh-Speed Search Slow MotionVariable Speed Search Pause during playbackManual Tracking 16 ENInstant ReView Skip Search Index SearchNext Function Memory Repeat Playback18 EN Engage the ITR mode Instant Timer Recording ITRWatching Another Set the recording duration20 EN Reset the counterTape Remaining Time Display the counterRecording PlaybackBefore performing the Showview Timer Programming Access the Showview screen22 EN Enter the Showview numberEngage the recorder’s timer mode Set the VPS/PDC modePress SP/LP p Press VPS/PDC to select on or OFF24 EN Express Timer ProgrammingVPS/PDC Recording To Timer-Record Weekly Or Daily SerialsEnter the channel position Press PR +Cancel or change a programme Check, cancel and change programmesReturn to the timer mode Disengage the timer modeConfirm the overlapping programmes Cancel or change programme settingSelect the programme to modify Engage the Auto Satellite Programme Recording mode Select the L-2 Select modeProgramme Recording 28 ENEdit From a Camcorder Another Video Recorder Set the input mode of recording deck30 EN Start the source playerConnecting To a Satellite Receiver 32 EN Select the input modeConnect the decoder Set the tunerAccess the Initial Set screen Showview System SetupGuide Program Number Set Guide Program NumberAccess the Mode Set screen Mode SetSelect the mode Select the mode settingThis feature helps you to adjust the playback picture You can set the B.E.S.T. Biconditional Equalised SignalWhen this function is set to ON, the timer is Off, and automatically disengaged when the recorder isFor Example 36 ENAbout Ntsc Playback Tuner Set Access the Auto Channel Set screen38 EN Auto Channel SetView the Confirmation screen Perform Auto Channel SetPress OK twice Manual Channel Set 40 ENDelete a Channel When Receiving a Scrambled BroadcastSet Stations a 42 ENSet Stations B Station Name TV Station And ID ListClock Set Access the Clock Set screen44 EN Set Just Clock Set the date and timeSet the source channel position for clock data Start the clock operationExit the Video Channel Set mode Access the Video Channel Set modeVideo Channel Set 46 ENPower Recording 48 ENOther Problems Playback 50 ENConnecting To a Satellite Receiver Auto Channel Set Auto Set UpTimer warning display Tuner Set Watching AnotherMonochrome signal, 625 lines Signal systemMemory backup time Approx min LP HR-J480EU only 480 min. with E-240 video cassette