JVC HR-J280, HR-J289EU, HR-J281 specifications 10 EN, Perform Preset Download, Set the video channel

Page 10

10 EN

INITIAL SETTINGS (cont.)

Preset Download

Auto Channel Set by Downloading from TV/Auto Clock Set/Auto Guide Program Number Set

ATTENTION

You can use this function only with a TV offering T-V Link, etc.* Be sure to use a fully-wired 21-pin SCART cable.

*Compatible with TVs offering T-V Link, EasyLink, Megalogic, SMARTLINK, Q-Link, DATA LOGIC or NexTView Link via fully-wired 21-pin SCART cable. The degree of compatibility and available functions may differ by system.

If you have connected the recorder to your TV via the AV connection ( pg. 7), the recorder will automatically perform Preset Download instead of the Auto Set Up in step 4 on page 9. After downloading, the recorder sets the clock and Guide Program numbers automatically.

Perform steps 1 to 3 of “Auto Set Up” on page 8 before continuing.

A Perform Preset Download.

Press OK. The AUTO SET/T-V LINK display appears on the front display panel and/or on the TV screen.

On the front display panel

Press rt to select “CH – –” and press OK or e.

On the on-screen display

Press rt to move the highlight bar (pointer) to “T-V LINK” and press OK or e.

NOTES:

●For details, refer to the instruction manual of your TV.

●In the area where no TV station transmits a PDC (Programme Delivery Control) signal, the recorder can perform neither Auto Clock Set nor Auto Guide Program Number Set.

●If there is a power cut, or if you press 1 or MENU while downloading or set up is in progress, it will be interrupted; be sure to turn off the recorder power once and try again from the beginning.

●Auto Clock Set may not function properly depending on the reception condition.

●On this recorder, the characters available for station names (ID) are A–Z, 0–9, –, f, + and I (space). Some names of

downloaded stations may differ from those of your TV ( pg. 42).

Preset positions on the front display panel increase from “CH1”; do NOT press any button on the recorder or remote control until the front display panel shows clock time, “(CH) 1” or “– –:– –” as illustrated on page 11.

●If you are using the on-screen

display, the T-V LINK screen will appear. Then the GUIDE PROG SET screen will appear during Guide Program Number Set. When Preset Download is completed, “COMPLETED” appears for about 5 seconds, then the normal screen appears.

●If you press any button on the recorder or remote control

while downloading is in progress, it will be interrupted.

B Set the video channel.

Set the video channel to off manually. ( pg. 46)

Page 9 Page 11
Image 10
Page 9 Page 11
Contents Video Cassette Recorder English Safety Precautions Moisture Condensation Front View Front Display Panel ON-SCREEN Display How To Use Operating JVC TVs Connect the recorder to TV Check the contents Situate the recorder Connect the recorder to mainsSelect your country Auto Set UpTurn on the recorder Before starting, make sure of the followingOn the front display panel Perform Auto Set UpSelect the language On the on-screen displaySet the video channel Perform Preset Download10 EN Press rt to select CH - and press OK or eLanguage for the on-screen display Just ClockLanguage Access the Main Menu screenAccess the Country Set screen 12 ENVCR Auto Standby NexTView Link TV Auto Power OnLink Functions Direct RecBasic Playback 14 ENVariable Speed Search Slow MotionHigh-Speed Search Pause during playbackManual Tracking 16 ENInstant ReView Next Function Memory Index SearchSkip Search Repeat Playback18 EN Watching Another Instant Timer Recording ITREngage the ITR mode Set the recording durationTape Remaining Time Reset the counter20 EN Display the counterPlayback Recording22 EN Access the Showview screenBefore performing the Showview Timer Programming Enter the Showview numberPress SP/LP p Set the VPS/PDC modeEngage the recorder’s timer mode Press VPS/PDC to select on or OFFExpress Timer Programming 24 ENEnter the channel position To Timer-Record Weekly Or Daily SerialsVPS/PDC Recording Press PR +Return to the timer mode Check, cancel and change programmesCancel or change a programme Disengage the timer modeConfirm the overlapping programmes Cancel or change programme settingSelect the programme to modify Programme Recording Select the L-2 Select modeEngage the Auto Satellite Programme Recording mode 28 ENEdit From a Camcorder 30 EN Set the input mode of recording deckAnother Video Recorder Start the source playerConnecting To a Satellite Receiver Connect the decoder Select the input mode32 EN Set the tunerGuide Program Number Set Showview System SetupAccess the Initial Set screen Guide Program NumberSelect the mode Mode SetAccess the Mode Set screen Select the mode settingWhen this function is set to ON, the timer is You can set the B.E.S.T. Biconditional Equalised SignalThis feature helps you to adjust the playback picture Off, and automatically disengaged when the recorder is36 EN For ExampleAbout Ntsc Playback 38 EN Access the Auto Channel Set screenTuner Set Auto Channel SetView the Confirmation screen Perform Auto Channel SetPress OK twice 40 EN Manual Channel SetWhen Receiving a Scrambled Broadcast Delete a ChannelSet Stations a 42 ENSet Stations B TV Station And ID List Station NameClock Set Access the Clock Set screen44 EN Set the source channel position for clock data Set the date and timeSet Just Clock Start the clock operationVideo Channel Set Access the Video Channel Set modeExit the Video Channel Set mode 46 ENPower 48 EN RecordingOther Problems 50 EN PlaybackTimer warning display Tuner Set Auto Channel Set Auto Set UpConnecting To a Satellite Receiver Watching AnotherMemory backup time Approx min Signal systemMonochrome signal, 625 lines LP HR-J480EU only 480 min. with E-240 video cassette
Top Page Image Contents