JVC LPT0679-001B AV Insert Editing VHS deck only, Prepare the recording cassette, Start Editing

57

A Make connections.

Connect the player’s VIDEO OUT or S-VIDEO OUT and AUDIO OUT connectors to your recorder’s VIDEO or S-VIDEO and AUDIO input connectors on the front panel.

B Select the recording deck.

Press VHS or DV.

●When using the DV deck as the recording deck, press so that the video and audio signals from the VIDEO/S-VIDEO and AUDIO L + R input connectors can be recorded. The dubbing direction indicator ( VHS) lights.

C Load a cassette.

For the VHS deck

Insert a VHS (or S-VHS) cassette with the record safety tab intact, or cover the hole using adhesive tape.

For the DV deck

Insert a Mini DV cassette with the erase protection switch set to “REC”.

D Set the recorder’s input mode.

Press AUX (number key “0”) and/or PR to select “F-1”.

●When using the VHS deck as the recording deck, set “VHS F-1 INPUT” to “VIDEO” for the AUDIO/VIDEO input connectors,

or “S-VIDEO” for the AUDIO/S-VIDEO input connectors, depending on the connectors being used. ( pg. 53)

E Prepare the recording cassette.

For the VHS deck

Load the recording cassette into the VHS deck, and play it back to determine the edit-out point (the end of the segment to be replaced) using the JOG dial, or pressing w

eand 9.

Then press 0000 to reset the counter.

For the DV deck

Load the recording cassette into the DV deck.

F Locate the start point.

Press 4 to start playback of the tape in your recorder, and press 9 when you reach the point where you want to start dubbing.

G Engage the Insert Editing mode.

Press INSERT.

●Your recorder enters the Insert Pause mode. (“o”, “u” and “i” light up on the front display panel.)

●The TV screen changes from the still picture to the input source you are going to record.

H Start Editing.

Load the source cassette and play back the segment that is to be inserted. When you reach the start of the section of the source tape that you wish to insert, press 4 to start the tape in your recorder; Insert Editing begins at this point.

●“o” and “u” are displayed on the front display panel.

I End Insert Editing.

For the VHS deck

At counter “0:00:00”, Insert Editing will stop automatically while the tape continues running in the Play mode. If you wish to stop Insert Editing before the specified edit-out point, press 0000.

For the DV deck

Press 8 to stop recording on the DV deck.

AV Insert Editing (VHS deck only)

If you want to replace the picture, Hi-Fi audio soundtrack and normal audio soundtrack all at the same time ...

... In step 7, after you press INSERT, press A.DUB also.

(“o” and “u” blink and “i” lights up on the front display panel.)

NOTES:

●Once the Insert Editing starts, you can not use the other deck.

●All necessary cables can be obtained from your dealer.

●Insert Editing cannot be performed on a VHS (or S-VHS) cassette that has had its record safety tab removed, or on a Mini DV cassette that has had its erase protection switch set to “SAVE”.

●When Insert Editing is performed on a tape that has been recorded on another video recorder, the inserted portion may appear distorted.

●In Insert Editing, the recording speed (SP/LP) is determined by the previous recording to be replaced. If the previous recording’s speed changes within a single edit, the inserted picture will be distorted at the switching point. (VHS deck only)

●A small portion of the recording which precedes an insert edit may become erased.

●Insert Editing is also possible using the rear panel AV1 (L-1) IN/ OUT or AV2 (L-2) IN/DECODER connector. When using these 21-pin SCART connectors, be sure to select the correct input mode (“L-1” or “L-2”) in step 4.

●Insert Editing is not possible using the DV IN/OUT connector.

●Insert Editing is not possible on a blank portion of the tape.