JVC LPT0679-001B specifications Turn off the recorder once and connect, Not connected between TV

Page 86

86			TROUBLESHOOTING (cont.)
OTHER PROBLEMS
	SYMPTOM	POSSIBLE CAUSE	CORRECTIVE ACTION
1.	Whistling or howling is heard from the	● The camcorder’s microphone is too	Position the camcorder so its microphone
	TV during camcorder recording.	close to the TV.	is away from the TV.
		● The TV’s volume is too high.	Turn the TV’s volume down.

2.	When scanning channels, some of	● Those channels have been designated to	If you need the skipped channels, restore
	them are skipped over.	be skipped.	them ( pg. 74).

3.	The channel cannot be changed.	● Recording is in progress.	Press 9 to pause the recording, change
			channels, then press 4 to resume
			recording.

4.	Channel settings that were made	● After the manual settings were made,	Perform manual setting again.
	manually seem to have changed or	Auto Channel Set was performed.
	disappeared.

5.	No channels are stored in the	● The TV aerial cable was not connected	Turn off the recorder once and connect
	recorder’s memory.	to the recorder when Auto Set Up was	the TV aerial cable to the recorder
		performed.	properly, then turn on the recorder again.
			The recorder will try Auto Set Up again
			( pg. 13).
		● The fully-wired 21-pin SCART cable was	Turn off the recorder once and connect
		not connected between TV and the	the fully-wired 21-pin SCART cable to the
		recorder when Preset Download was	recorder properly, then turn on the
		performed.	recorder again. Then perform Preset
			Download again ( pg. 14).

6.	The remote control won’t operate the	● The remote control brand setting is	Re-set the remote control to the correct
	TV or satellite receiver.	incorrect.	brand. ( pg. 61, 62)

7.	No picture appears when you connect		Turn off the recorder or the connected
	a device to DV IN/OUT connector.		appliance once, then turn it on again.

ATTENTION

This recorder contains microcomputers. External electronic noise or interference could cause malfunctioning. In such cases, switch the recorder off and unplug the mains power cord. Then plug it in again and turn the recorder on. Take out the cassette. After checking the cassette, operate the unit as usual.

Image 86

Contents Video Cassette Recorder Do not place the recorder Do not expose the apparatus to dripping or splashingSome Do’s And Don’ts On The Safe Use Of Equipment Above ALLFront View Rear View Do not remove itPDC* Indicator pg Front Display PanelON-SCREEN Display for DV deck Remote Control VHSHow To Use Remote Control LCDCheck Contents Connect the recorder to TV Recorder and the TV’s 21-pin Scart connectorSituate the recorder Connect the recorder to mainsVideo Connection 8To connect to a TV with S-VIDEO/AUDIO in connectorsAerial connector Turn on the recorder Auto Set UpPerform Auto Set Up Before starting, make sure of the followingOn the on-screen display Perform Preset DownloadPress rt to select CH - and press OK or e Just Clock pg , Just ClockVCR Auto Standby NexTView Link TV Auto Power OnLink Functions Direct RecAttach the Satellite Controller Installing Satellite ControllerSituate the Satellite Controller Make connectionsSetting satellite receivers brand and channel Select the satellite receiver’s channel for testing Check the result of the testBasic Playback VHS deckStart recording Choose a programmeSet the tape speed Pause/Resume recordingActivate frame-by-frame playback Slow MotionPause during playback Index Search High-Speed Turbo SearchVariable Speed Search Skip SearchActivate Repeat Playback Next Function MemoryRepeat Playback Stop Repeat PlaybackManual Tracking Adjust the tracking manuallySoundtrack Selection Ntsc PlaybackRecording Resume Function Instant Timer Recording ITREngage the ITR mode Accidental erasure preventionSet the counter display Reset the counterTape Remaining Time Press 0000 before starting recording or playbackReceiving Stereo and Bilingual Programmes Engage the Record-Pause modeRetake Locate the start pointPlayback RecordingPress DV DV deckSelect the DV deck Find the programme start pointDV recording indicator turns off PLAYBACK/RECORDING on DV Deck Search, or 3 for reverse high-speed search For forward high-speed searchDuring playback, turn the JOG dial quickly to the right During playback or still, press 5 for forward high-speedRecording Features Time Code See Audio REC onEnter the PlusCode number Access the PlusCode displaySelect the deck Transmit the PlusCode numberCheck the programme data Set the PDC modeEngage the recorder’s timer mode Return to the normal screenAccess the Programme screen Express Timer ProgrammingAccess the PlusCode screen Enter the programme start timeEnter the programme date To Timer-Record Weekly Or Daily SerialsPDC Recording Enter the channel positionSet the programme start/stop time and channel Enter the programme modeBefore performing the 24 Hour Express Timer Programming For the VHS deckPage Cancel or change a programme Disengage the timer modeAccess the Programme screen/display Return to the timer modeSelect the programme to modify Cancel or change programme settingConfirm the overlapping programmes Overlapping programmes blink on the TV screenLoad cassettes Tape DubbingFrom DV to VHS Dubbing An Entire Cassette Select the dubbing directionPress DV, then press SP/LP p Dubbing direction indicator VHS lightsFrom VHS to DV Dubbing An Entire Cassette Prepare the VHS deck for dubbing From DV to VHSLocate the start point on the DV deck Pause dubbingLocate the start point on the VHS deck VHS playback indicator and DV recording indicator lightFrom VHS to DV Prepare the DV deck for dubbingSet the edit mode. VHS deck only Set the recorder’s input modeSelect the recording deck Start the camcorderRecorder Video input If the camcorder has no S-VIDEO output connectorSimultaneous Dubbing PlayerAdvantages of S-VHS video recorders Set the input mode of recording deckAnother Video Recorder Start the source playerPlayer Recorder RecorderAnother recorder Access the Main Menu screen Press rt to moveDecoder connector Select SettingVHS F-1 Input Setting Select the input mode for the Video Video connectorDV Audio Dubbing Audio DubbingVHS Audio Dubbing Pre-recorded tape Audio-dubbed tape CD player, etcPress A.DUB Engage the Audio Dubbing modeEnd Audio Dubbing VHS Insert Editing DV Insert Editing SP mode onlyInsert Editing Source tapePrepare the recording cassette Engage the Insert Editing modeAV Insert Editing VHS deck only Start EditingInsert a VHS or S-VHS cassette and a Mini DV cassette Access the R.A.Edit screenSelect the programme Press R.A.EDIT. The R.A.Edit screen appearsStart Random Assemble Editing Locate the end pointPrepare the source tape End Random Assemble EditingDisplay the code Change the remote control codeSet the remote control code Change the recorder’s codeSet the TV brand code TV Multi-Brand Remote ControlTV PR +/-, TV %+/- Volume, TV Muting, number keys Operate the TVOperate the satellite receiver Satellite Receiver Multi-Brand Remote ControlSet the satellite receiver brand code Digital printer About DV IN/OUT connectorTo DV in connector Outdoor unit Satellite cable Aerial ConnectorAerialPin Scart connector Mains outlet AUX in or Tape Monitor Make connectionsFM tuner CD player Stereo amplifier Speaker TelevisionSelect the mode Mode SetAccess the Mode Set screen Select the mode settingScreen Mode SETPowered back on Control, or press 7 on the recorderVHS Mode SET VHS Mode SET Picture reproduction is also linked to this function Using this video recorder as the source player for editingRental cassettes We recommend that you set Digital TBC/NR to on whenDV Mode SET Auto Channel Set Tuner also by Preset Download pgTuner Set Perform Auto Channel SetView the Confirmation screen Manual Channel Set Select the item Delete a ChannelChange Station Channel Position Delete a channelSet Stations a Set Stations BSelect the channel to fine-tune Access the Manual Channel Set screenPerform tuning Press OK twice. The Manual Channel Set screen appearsTV Station And ID List Station NameTV Station Channel Number Guide Access the Clock Set screen Clock SetSet the source channel position for clock data Set the date and timeSet Just Clock Start the clock operationGuide Program Number Video Plus+ System SetupGuide Program Number Set Enter the Guide Program numberNo power is supplied to the recorder Connect the mains power cordAdhesive tape, cover the hole where Recording cannot be startedThere is no cassette loaded, or Tab removed Tab was removedVHS deck DV deckTurn off the recorder or the connected Turn off the recorder once and connectNot connected between TV Recording Timer RecordingPlayback Hz to 20,000 Hz Hi-Fi audio Maximum recording time Scan systemLines VHS Lines S-VHS Frequency range Hz to 10,000 Express Timer Programming Auto Channel Set Auto Set UpClock Set Connecting To a Printer Preset Download Random Assemble EditingMemo