JVC SR-VS20EK, LPT0543-001A setup guide Timer Warning, PDC Recording, Satellite Receiver Users

Page 21

 

SET TAPE SPEED

5 Press SP/LP/EP (

) to set the tape speed.

6

SET PDC MODE

Press PDC to select "ON" or "OFF".

If "VPS/PDC ON" is displayed on the screen or "VPS/

PDC" is lit on the display panel, PDC is set to ON.

 

If "VPS/PDC OFF" is displayed on the screen or "VPS/

 

PDC" is not lit on the display panel, PDC is set to OFF.

 

 "PDC Recording" in the column below.

 

● VPS (Video Programme System) recording is not

 

currently available in the U.K. and not possible with

 

this recorder.

 

 

RETURN TO NORMAL SCREEN

 

Press PROG or OK. "PROGRAM COMPLETED" appears

 

on the screen for about 5 seconds, then normal screen

7 appears. If the timer programme is overlapped with

 

another one that was already set, "PROGRAM

 

OVERLAPPED" appears on screen and "Err" appears on

 

 



21

Satellite Receiver Users

To timer-record a satellite broadcast using the VIDEO Plus+ system:1

2Perform "Satellite Receiver Control Setting" ( pg. 12). Perform steps 1 – 8. In step 4, the display panel shows "L2" for the preset position. In step 6, you cannot set

3PDC to ON.

Leave the satellite receiver's power on.

ATTENTION

Regarding Guide Program Number Set

"GUIDE PROG SET" appears after performing step 3 if the Guide Program number for the PlusCode number you entered has not been set.

● If you want to set the Guide Program number for the satellite broadcast station, press the NUMBER key "0" to change "TV PROG" to "SAT". Press %fi to input the preset position number on which your recorder or satellite receiver receives that station, then press OK or # to set the Guide Program Number. The VIDEO Plus+ Program screen appears.

 

the front display panel. ( pg. 25)

 

 

 

● Repeat steps 1 – 7 for each additional programme.

 

 

8

ENGAGE RECORDER’S TIMER MODE

Press ‰ (TIMER). The recorder turns off automatically

and ‰ appears on the display panel.

 

● To disengage the timer, press ‰ (TIMER) again.

NOTES:

GUIDE PROG SET

GUIDE PROG TV PROG

2– –

[5∞] =

[0] : SAT

[PROG] : EXIT

(Ex.) To timer-record a BBC2 programme with the VIDEO Plus+ system.

*If your recorder receives BBC2 on the preset position 2, press OK or # after entering "2".

● To Change The Stop Time . . .

. . . press STOP +/– in step 4. You can compensate for anticipated

programme schedule delays this way.

● To Timer-Record Weekly Or Daily Serials . . .

. . . in step 4, press WEEKLY (NUMBER key “9”) for weekly serials

or DAILY (NUMBER key “8”) for daily serials (Monday – Friday).

Either "WEEKLY" or "DAILY" appears on the screen. Pressing the

button again makes the corresponding indication disappear.

● You can programme the VHS deck and the DV deck to timer-

record as many as 6 programmes each. If you try to programme

each deck to record a seventh, "PROGRAM FULL" appears on

Timer Warning

If you have programmed your recorder to timer-record a programme or a series of programmes, a warning appears on the screen to tell you that the recording is due to start in 5 minutes.

– WARNING–

TIMER RECORDING TO START SOON

[]

screen and "FULL" appears on the front display panel. To record

the extra programme, you must first cancel any unnecessary

programmes ( pg. 24).

● It is not possible to timer-record a TV programme with a PlusCode

number which starts with "0".

● It is not possible to timer-record the same programme on both the

VHS deck and the DV deck simultaneously.

● If the times that are programmed for recording on the DV deck and

on the VHS deck overlap, the earlier start time takes precedence. If

the start times are the same, the VHS deck takes precedence.

NOTES:

●The warning only appears if you’re not in the Timer mode at the time.

●If this recorder is being used as the player for tape dubbing, the warning screen will be recorded on the tape in the other video recorder.

The warning blinks for the entire 5 minutes leading up to the start of timer recording. To clear the display, press .

PDC Recording

Now available from some TV stations, PDC (Programme Delivery Control) is a service designed to assure safe, accurate timer recording. With this system, special code signals are transmitted together with the audio/video signals. These code signals control your video recorder and have precedence over the advertised times which you may have preset into the timer. This means that your recorder will start and stop recording when the preset TV programmes actually start and end — even if the broadcast time of a preset TV programme is changed from what has been advertised. PDC is currently available nationally on BBC1, BBC2, Ch.4 and Ch.5, except from a few small relay transmitters. Ch.3 operates a PDC service in some areas.

All channels intend to offer this service in due course. Check your TV programme listing guide for latest information. If the channel you intend to record does not offer a PDC service your recorder will not start recording if PDC has been selected. Be sure to set PDC to "OFF" if PDC is not available on your selected channel ( step 6 above).

NOTES:

●PDC recording is also possible when a satellite receiver or a cable system is connected to AV2 (L-2) IN/DECODER on your recorder.

●PDC recording is also possible via the AV1 (L-1) IN/OUT connector.

Page 20 Page 22
Image 21
Page 20 Page 22
Contents SR-VS20EK Connection to the mains supply in the United Kingdom Safety PrecautionsDo not place the recorder… Do not block the recorder’s ventilation openings or holesDo not expose the apparatus to dripping or splashing Some Dos And Donts On The Safe Use Of Equipment Quick SET UP Guide Connector Scart Back of TVBack of Recorder RF Cable provided Aerial connectorBefore performing the following procedure, make sure that Step Auto SET UPShows either the display as illustrated on Or remote control until the display panelProgress, this process will be interrupted You will need to start again. See Notes belowC1If both auto channel set and auto clock set have failed Link Functions TV Auto Power OnTurn on the Recorder NexTView LinkSatellite Receiver Control Setting Enter Satellite RECEIVER’S Brand Select Satellite RECEIVER’S Channel for TestingCheck Result of Test CodePlayback Pause During Playback Activate HIGH-SPEED SearchTime Code DV Deck Tape Position Indicator VHS DeckRecording DV Deck Select DV DeckPress SP/LP/EP Mini DVReset Counter Engage ITR ModeSET Recording Duration Display Remaining TimeVideo Plus+ Timer Programming Timer Warning PDC RecordingSatellite Receiver Users Enter Programme Express Timer ProgrammingStart Time TimeTimer Mode SET PDC ModeReturn to Normal ScreenCheck, Cancel And Replace Programmes EX. Programme 1 you have just made When programmes overlap each otherProgramme 4 overlap each other on the VHS deck SP/LP/EPSuper VHS S-VHS Super VHS ET S-VHS ET VHS Deck Only Recording According To Tape TypePress S-VHS ET on the recorder. You can check Engage S-VHS ET ModeAppears on the TV screen, press S-VHS ET again About 5 seconds to set it to onAccess VHS Mode SET Access Main Menu ScreenPlayback/ Recording According To Tape Charac- teristics S.T. Picture System VHS Deck OnlyPlayback RecordingOr press Record on the recorder During B.E.S.TPlayback Picture Adjustment Manual Tracking VHS Deck OnlyDigital TBC/NR VHS Deck Only Video Stabilizer VHS Deck Only Digital 3R VHS Deck OnlyActivate Index Search Looking For Scene You WantSkip Over Unwanted SectionsActivate Instant ReviewInstant ReView Soundtrack Selection VHS Deck Selecting Sound You WantDuring Playback USE12BIT Mode Setting Audio-dubbed Mini DV Tape 1Sound Mode Selection DV Deck12BIT Mode Sound YOU Hear Soundtrack Selection DV DeckType of Broadcast On-screen Display Being Received Receiving Nicam Stereo And Bilingual ProgrammesMinimizing Picture Degradation While Editing Select Picture Control SET ModeReturn to Normal Screen Picture Control VHS Deck OnlyLoad Cassettes Tape DubbingSelect Dubbing DirectionSelect Dubbing Direction Normal DubbingLocate Start Point Pause DubbingProgram Editing Memory 8 programmes x 8 scenes Random Assemble EditingEngage VHS Deck to ScenesPause Press R.A.EDITCamcorder Edit FromIf the camcorder has a DV OUT/IN connector Recorder Recorder If the camcorder has an S-VIDEO output connectorRecorder PlayerEdit To Or From Another Video Recorder Input ModeSET Recording DECK’S Start Source PlayerYour recorder TV Receiver AV modeRecorder Player Pin Scart Cable Not provided Another recorderAudio Dubbing SET Input ModeVHS Audio Dubbing DV Audio DubbingEND Audio Dubbing Insert Editing DV Insert Editing SP Mode OnlyLocate END Point VHS Insert EditingEngage Insert Editing Start EditingEND Insert Editing Select Setting OUTPUT/INPUT SettingFor L-1 Output For L-1 InputVHS/AUDIO OUT Setting VHS F-1 Input SettingChange Remote Controls Code Remote Control FunctionsSET Remote Controls Code Display CodeControl Your TV Using Additional Buttons TV Multi-Brand Remote ControlTV PR +/-,TV/VCR, TV TV Brand Name CodeBrand Code Satellite Receiver Multi Brand Remote ControlOperate Satellite Receiver TV PR +/-,NUMBER keysENABLE/DISABLE ON-SCREEN Display Access Mode SET ScreenOther Functions On-Screen DisplayPower Save Mode Power SAVE, then pressOK or To set to on Auto Timer Auto SP→LP Timer VHS Deck OnlyNext Function Memory Repeat Playback VHS Deck Only Resume RecordingRetake VHS Deck Only Ntsc Playback VHS Deck OnlyBack of TV Connecting To Satellite ReceiverSatellite Receiver Unit Back of RecorderAudio Cable not provided Mains outlet Connecting To Stereo SystemDigital printer Connecting To a PrinterConnecting To a Video Titler Press DV or VHS for the playing deck, then press Play Enter TitlePerform Auto Channel SET Tuner SetAuto Channel Set Pointer to Auto CHProcedures Screen preset positionsAfter Scan Completed Is displayed on the screenStoring Channels Manually Change Station Preset Position Fine-Tuning Channels Already StoredDelete a Channel Switch Stations Access ManualSelect Item Channel SET ScreenClose Confirmation Screen +, space and stop when the desired characterSet Stations B Station name begins BlinkingStation Name TV Station And ID ListTV Station Channel Number Guide Just Clock Clock SetVideo Plus+ System Setup NumberGuide Program Number Set Questions And Answers ‰ remain lit on the display panel. Is there Problem?What happens if the tape runs out during recording? Safety tab removed Removed TroubleshootingNot been turned on Turned on Input mode is not correct Recording cannot be startedCassette with the Record Safety tab Protection switch set to RECProtection switch set to Save Protection switch to REC Load a cassette with the eraseOther Problems Index CopiePediting.  pg Antenna in Connector enables connection Review Rew How To Use Remote Control LCDPAL-type colour signal and Ccir PAL-type colour signal, 625 linesProvided accessories
Top Page Image Contents