VCR Plus+ Timer Programing, 24HR Quick Programing

GUIDE CH : 12

VCR CH : – – –

PRESS NUMBER KEY (0–9)

OR ( , ), THEN (OK)

PRESS (PROG.) TO END

GUIDE CHANNEL SET

Channel number

Stop time

Start time

VCR Plus+® Timer Programing

The PlusCode programing numbers are the numbers next to the program in most TV listing.

Load a cassette with the record safety tab intact. If not, set “REC SAFETY” to “OFF” ( pg. 19). The VCR turns on, and the counter is reset, automatically.

A Press PROG. on the Remote to access the PlusCode No. screen.

PLUSCODE NO.

PRESS NUMBER KEY (0–9)

PRESS (+/–) TO SET

EXPRESS PROGRAMMING

PRESS (PROG.) TO END

VCR PLUS+ SYSTEM

BPress the appropriate Number keys to input the PlusCode number, then

press OK or SHUTTLE PLUS e. Check to make sure the setting is accurate on the Program screen.

PLUSCODE NO.					PROGRAM 1
PLUSCODE NO.				(PLUSCODE NO. 12345678)
	1 2 3 4 5 6 7 8			START	STOP
				8:00PM	10:00PM
				DATE	CH
		12/24/04			12 SP
				FRI
PRESS NUMBER KEY (0–9)				FRI
PRESS NUMBER KEY (0–9)
	THEN (OK)		PRESS (8=DAILY, 9=WEEKLY
PRESS (PROG.) TO END			STOP+/– = STOP TIME, SP/EP)
VCR PLUS+ SYSTEM			PRESS (PROG.) TO END

● If the Guide Channel Set screen appears after pressing OK, press the Number keys, CH+/– or SHUTTLE PLUS rtto input the number of the channel on which the broadcast for the PlusCode number is received on the VCR, then press OK.

●To set the tape speed, press SP/EP.

●To change the stop time, press STOP+/–.

●To timer-record daily (Sunday–Saturday) or weekly serials, press DAILY (Number key “8”) or WEEKLY (Number key “9”). Pressing the button again makes the “DAILY” or “WEEKLY” display disappear.

●If you made a mistake, press CANCEL to access the PlusCode No. screen again.

●If an incorrect PlusCode number or the one for a broadcast already finished has been input, “ERROR” is displayed for about 5 seconds, then the PlusCode No. screen reappears.

CPress OK or PROG..

●If “PROGRAM NOT COMPLETED PROGRAM OVERLAP”

appears, see “Program Overlap Warning Display” ( pg. 17).

DPress TIMER. The VCR turns off automatically and “#” is displayed on the display panel.

Express Timer Programing

Load a cassette with the record safety tab intact. If not, set “REC SAFETY” to “OFF” ( pg. 19). The VCR turns on, and the counter is reset, automatically.

APress PROG. on the Remote to access the PlusCode No. screen.

B Press START+/– once to access		PROGRAM 1
Program screen.		START	STOP
Press START+/–,STOP+/–,DATE+/– or		– –:– –AM	– –:– –AM
		DATE	CH
CH+/– repeatedly to enter the start
		– –/– –/– –	– – –	SP


time, stop time, date or channel.
	PRESS (+/–, SP/EP, 8=DAILY
● Press and hold START+/– or STOP+/–	9=WEEKLY), THEN (0K)
to increase the time in 30-minute	PRESS (PROG.) TO END

intervals.

● To set the tape speed, press SP/EP.
● To timer-record daily (Sunday–			PROGRAM 1
Saturday) or weekly serials, press		START		STOP
DAILY (Number key “8”) or WEEKLY		DATE		CH
		8:00AM		9:00AM
(Number key “9”). Pressing the
				110	SP
		12/24/04		110	SP
		FRI
button again makes the “DAILY” or		FRI
button again makes the “DAILY” or	PRESS (+/–, SP/EP, 8=DAILY
“WEEKLY” display disappear.	9=WEEKLY), THEN (0K)
	PRESS (PROG.) TO END

CPress OK or PROG..

●If “PROGRAM NOT COMPLETED PROGRAM OVERLAP”

appears, see “Program Overlap Warning Display” ( pg. 17).

DPress TIMER. The VCR turns off automatically and “#” is displayed on the display panel.

24HR Quick Programing

You can program a timer recording that starts within 24 hours using the JOG dial on the VCR.

Load a cassette with the record safety tab intact or set “REC SAFETY” to “OFF” ( pg. 19). The VCR turns on, and the counter is reset, automatically.

A Press 24HR QUICK PROGRAM on the

VCR. The start time indicator ( ) starts blinking on the display panel.

B Turn the JOG dial to the left or right to set

the start time. ● One click stop of the JOG dial changes the time in 5-minute intervals.

C Push the JOG dial. The stop time

indicator ( ) starts blinking on the display panel. Turn the JOG dial to the left or right to set the stop time.

D Push the JOG dial. Turn the JOG dial to

the left or right to select the channel. ● To set the tape speed, press SP/EP. The

current setting for the tape speed appears on the display panel for about 5 seconds. Press SP/EP again to change the setting while tape speed is displayed.

ETo engage timer recording standby mode, press 24HR QUICK PROGRAM. The VCR turns off automatically and “#” is displayed on the display panel.

NOTES:

●If “Err” appears on the display panel, repeat the above steps again.

●When a menu screen is shown, you cannot use 24HR Quick Programing function. Press MENU to return to normal screen, and try again.

●You can use 24HR Quick Programing function also when the VCR is turned off.

●For 24HR Quick Programing function, the program overlap warning display does not appear even if some programs overlap each other.

To use the VCR while it is in timer recording standby mode

Press TIMER, then press POWER 1. After you use the VCR, press TIMER again to put the VCR into timer recording standby mode.

— 16 —