JVC HR-DD949EE Override Automatic Tracking, Adjust Tracking, Manually, Return to Automatic

Page 12

12EN

PLAYBACK (cont.)

Manual Tracking

PICTURE

 

PLAY

3R

 

 

8

STOP

6

 

5/8

q

1

Á

TV PROG

 

 

FF

REW

 

 

 

REVIEW

 

2

 

 

1

2

 

3

4

5

 

6

7

8

 

9

 

0

 

4

 

PLAY

 

TV PROG

 

 

 

REW

 

 

FF

 

 

 

 

 

3

STOP

 

 

 

1

 

 

 

PUSH JOG

Tape Position Indicator

Your video recorder is equipped with automatic tracking control. During playback, you can override this and adjust the tracking manually by pressing the TV PROG buttons.

OVERRIDE AUTOMATIC

TRACKING

 

Press SP/LP (

) on the remote to engage manual

1 tracking.

 

 

ADJUST TRACKING

 

MANUALLY

2 Press TV PROG + or to adjust tracking.

 

RETURN TO AUTOMATIC

 

TRACKING

 

Press SP/LP (

) on the remote to re-engage auto-

3 matic tracking.

 

NOTE:

When a new tape is inserted, the recorder enters the automatic tracking mode automatically.

3R Picture

3R(= Resolution and Response Recovery technology) maximises sense of resolution and sharpens image edges to make playback picture look better focused.

1

 

ACTIVATE 3R PICTURE

 

Press 3R PICTURE. The button will light.

 

 

 

To turn off 3R Picture, press 3R PICTURE again so

 

that the light goes off.

 

Normally it is recommendable to keep 3R Picture ON

 

 

(with the button lit).

The tape position indicator appears on screen when, from the Stop mode, you press FF, REW or perform an Index Search. The position of “5” in relation to “0” (beginning) or “+” (end) shows you where you are on the tape.

”O.S.D.” (pg. 9) must be set to “ON”, or the indicator will not appear.

3

0 ++ +

1:23:45 REMAIN 2:35

BeginningEnd

Depending on the type of tape used, picture quality

may be better with 3R Picture set to off.

If you use this recorder as the player for editing, be

sure to turn off 3R Picture before starting.

The setting will remain effective even though you

turn on/off the recorder.

Information On Colour System

NOTE:

Depending on the type of tape used, there may be times when the indication is not correct.

You can also record SECAM signals, or play back a MESECAM tape on this recorder. When a MESECAM tape is played back, "MESECAM" appears on the screen for about 5 seconds.

MESECAM is the designation for tapes with SECAM signals that have been recorded on a MESECAM-compatible PAL video recorder.

Image 12
Contents HR-DD949EE Safety Precautions Do not place the recorderCheck Contents Basic ConnectionsSituate Recorder Connect Recorder to MainsAuto Set Up Nitial Sett IngsAuto Channel Set Front Display PanelLanguage Set Access Video Channel SET Mode EN Initial SettingsVideo Channel Set SET Video ChannelExit Video Channel SET Mode Select TV SystemWith AV Connection Major CountriesClock Set ENABLE/DISABLE ON-SCREEN Display On-Screen DisplaysPress Push JOG %Þ to 13 3Basic PlaybackFeatures PlaybackActivate FRAME-BY-FRAME Activate HIGH-SPEED SearchAdjust Tracking Override Automatic TrackingManually Return to AutomaticActivate Instant Review Activate RepeatActivate Spatializer SpatializerSoundtrack Selection During PlaybackSET A/B Code Switch RE-SUPPLY PowerActivate Scene Finder Stop Scene FinderAudio signal during TimeScan Time Scan IndicatorTimeScan Variable-Speed Search/ Reverse PlayTimeScan TimeScan AudioSpeed SP Speed LP Audio output Basic Recording Recording Features S.T. Picture System EN RecordingRecording Display Panel IndicationPlay Pause Setup EN Timer RecordingMake List of Stored Station Names Channel Positions Guide Program Number SetAccess Guide Prog SET Screen NumberClose Menu If you already know the Guide Program number for a stationTimer Recording On NextPress TIMER. The recorder turns off automatically Press OK Repeat steps 1-5for each additional programmePress MENU, then try again from step Regular Timer Programming Press Stop +/- to enter the time you want recording to stopTimer Mode Engage RECORDER’SPress TV Prog + Access Mode SET Access ProgrammeRevise Programme InformationTimer Auto SP/LP TimerTimer Warning Engage Auto SP/LPTV Multi Brand Remote Control Control Your TV Using Additional ButtonsSET TV Brand Code TRY Operating TVSatellite Tuner Multi SET Satellite Tuner Brand CodeTRY Operating Satellite Tuner Satellite Tuner Brand CodeSET Recording DECK’S Input Mode Edit To Or From Another Video RecorderMake Connections Start Source PlayerIf another recorder has no 21-pin Scart connector PlayerRecorder Recorder PlayerEdit From a Camcorder SET RECORDER’S InputStart Camcorder Start RecorderSET Input Mode Locate Start PointEngage Audio Dubbing Start DubbingReset the Counter Locate END PointRecorder Your recorder Recorded tapeEngage Insert Editing Start EditingEND Insert Editing Access Jlip ID NO. SET Screen Interface Protocol ConnectorSET Jlip ID Number Return to Normal ScreenPerform Auto Channel SET View Confirmation ScreenTuner SET Storing Channels Manually Press Push JOG % twiceMajor Countries TV System Access Manual CH. SET Screen Select ItemDelete Channel Close ConfirmationSwitch Stations Perform TuningSelect NEW Station Select Channel toTV Station And ID List Station NameIf you are using the AV connection Set the TV to its AV modeSet the TV receiver to the Video Timer again RecordingOther Problems OubleshootingÄ remain lit on the display panel. Is there a problem? Questions and Answer S E NOpen the lid to access covered connectors and buttons IndexRear View Installing Batteries How To UseEN Index Specifications Backup time becomes shorter as the units internal partsHR-DD949EE