JVC HR-DD949EE specifications Engage Insert Editing, Start Editing, END Insert Editing

Ad

Page 37

INSERT

PLAY

		8
6		5/8
q	1	Á
	1	Á

A. DUB

	2
1	2	3
4	5	6
7	8	9
C.RESET	0	4
C.RESET
		PLAY

E

N

37

6

ENGAGE INSERT EDITING

Press INSERT.

● Your recorder enters the Insert-Pause mode. (" ", " "

and " " light up on the front display panel.)

● The TV screen changes from the still picture to the

input source you are going to record.

7

START EDITING

Load the source cassette and play back the segment

that is to be inserted. When you reach the start of the

section of the source tape that you wish to insert, press

PLAY to start the tape in your recorder; Insert Editing

begins at this point.

● " " and " " are displayed on the front display

panel.

8

END INSERT EDITING

At counter "0:00:00", Insert Editing will stop automati-

cally while the tape continues running in the Play

mode. If you wish to stop Insert Editing before the

specified edit-out point, press C.RESET.

FOR AV INSERT EDITING

If you want to replace the picture, Hi-Fi audio soundtrack and normal audio soundtrack all at the same time...

In step 6 above, after you press INSERT, press A. DUB also. (" " and " " blink and " " lights up on the front display panel.)

3

1

NOTES:

●Suitable leads can be obtained from your dealer.

●Insert editing is not possible with cassettes whose safety tab has been removed.

●When insert editing is performed on a tape that has been recorded on another video recorder, the inserted portion may appear distorted.

●In insert editing, the recording speed (SP/LP) is determined by the previous recording to be replaced. If the previous recording's speed changes within a single edit, the inserted picture will be distorted at the switching point.

●A small portion of the recording which precedes an insert edit may become erased.

●Insert Editing is also possible using the rear panel AV1 IN/ OUT or AV2 IN connector. When using these connectors, make sure to select the correct input mode in step 2.

Image 37

Contents HR-DD949EE Do not place the recorder Safety PrecautionsBasic Connections Check ContentsSituate Recorder Connect Recorder to MainsNitial Sett Ings Auto Set UpAuto Channel Set Front Display PanelLanguage Set EN Initial Settings Access Video Channel SET ModeVideo Channel Set SET Video ChannelSelect TV System Exit Video Channel SET ModeWith AV Connection Major CountriesClock Set On-Screen Displays ENABLE/DISABLE ON-SCREEN DisplayPress Push JOG %Þ to 13 3Playback BasicPlayback FeaturesActivate FRAME-BY-FRAME Activate HIGH-SPEED SearchOverride Automatic Tracking Adjust TrackingManually Return to AutomaticActivate Repeat Activate Instant ReviewSpatializer Activate SpatializerSoundtrack Selection During PlaybackRE-SUPPLY Power SET A/B Code SwitchActivate Scene Finder Stop Scene FinderTime Scan Indicator Audio signal during TimeScanTimeScan Variable-Speed Search/ Reverse PlayTimeScan Audio TimeScanSpeed SP Speed LP Audio output Basic Recording Recording Features EN Recording S.T. Picture SystemRecording Display Panel IndicationPlay Pause EN Timer Recording SetupMake List of Stored Station Names Channel Positions Guide Program Number SetNumber Access Guide Prog SET ScreenClose Menu If you already know the Guide Program number for a stationOn Next Timer RecordingPress OK Repeat steps 1-5for each additional programme Press TIMER. The recorder turns off automaticallyPress MENU, then try again from step Press Stop +/- to enter the time you want recording to stop Regular Timer ProgrammingEngage RECORDER’S Timer ModePress TV Prog + Access Programme Access Mode SETRevise Programme InformationAuto SP/LP Timer TimerTimer Warning Engage Auto SP/LPControl Your TV Using Additional Buttons TV Multi Brand Remote ControlSET TV Brand Code TRY Operating TVSET Satellite Tuner Brand Code Satellite Tuner MultiTRY Operating Satellite Tuner Satellite Tuner Brand CodeEdit To Or From Another Video Recorder SET Recording DECK’S Input ModeMake Connections Start Source PlayerPlayer If another recorder has no 21-pin Scart connectorRecorder Recorder PlayerSET RECORDER’S Input Edit From a CamcorderStart Camcorder Start RecorderLocate Start Point SET Input ModeEngage Audio Dubbing Start DubbingLocate END Point Reset the CounterRecorder Your recorder Recorded tapeStart Editing Engage Insert EditingEND Insert Editing Interface Protocol Connector Access Jlip ID NO. SET ScreenSET Jlip ID Number Return to Normal ScreenView Confirmation Screen Perform Auto Channel SETTuner SET Press Push JOG % twice Storing Channels ManuallyMajor Countries TV System Select Item Access Manual CH. SET ScreenDelete Channel Close ConfirmationPerform Tuning Switch StationsSelect NEW Station Select Channel toStation Name TV Station And ID ListSet the TV to its AV mode If you are using the AV connectionSet the TV receiver to the Video Recording Timer againOubleshooting Other ProblemsQuestions and Answer S E N Ä remain lit on the display panel. Is there a problem?Index Open the lid to access covered connectors and buttonsRear View How To Use Installing BatteriesEN Index Backup time becomes shorter as the units internal parts SpecificationsHR-DD949EE