JVC HR-DD949EE specifications Auto Set Up, Nitial Sett Ings, Auto Channel Set, Front Display Panel

Page 4

4EN

INITIALSETTINGS

Auto Set Up

Auto Channel Set

When the button on the recorder/remote control is pressed for the first time to power on the recorder after you plug the mains power cord into a mains outlet, the Auto Set Up function sets the tuner channels automatically.

You can refer to the front display panel and/or the on-screen display to perform this procedure.

 

 

8

6

 

5/8

q

1

Á

 

2

1 2 3

4

5

6

ATTENTION

Once you have performed Auto Set Up, even if the recorder's memory backup has expired, all the stored stations remain in the recorder's memory and the recorder will not perform Auto Set Up again.

If you have moved to a different area or a new station starts broadcasting in your area, perform tuner setting. pg. 39

Before starting, make sure of the following:

The TV aerial cable should be connected to the recorder.

The recorder's mains power cord should be connected to a mains outlet. pg. 3

If you want to use the on-screen display, the TV should be set to its AV mode (with AV connection pg. 3) or UHF channel 36 (with RF connection pg. 3).

 

1

 

START AUTO SET UP

 

 

 

Press

 

 

 

.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

The Auto Set Up function scans all the channels that

 

 

are receivable by your recorder. It then automatically

 

 

 

assigns each receivable channels to the TV PROG

 

 

 

buttons. It skips non-receivable channels.

 

 

 

As Auto Set Up progresses, the "

 

" mark on the

 

 

 

 

 

 

 

screen moves from left to right.

 

 

 

 

After you perform Auto Set Up, if the tuner channels

 

 

 

have not been set properly or if "CH – –" is displayed

 

 

 

on the front display panel, make sure that the aerial

 

 

 

cable is connected to the recorder properly and turn

 

 

 

off the recorder power once, and turn the power back

 

 

 

on to try Auto Set Up again.

 

 

 

 

If there is a power cut, or if you press

 

 

or MENU

 

 

 

 

 

 

 

while Auto Set Up is in progress, Auto Set Up will be

 

 

 

interrupted; be sure to turn off the recorder power once

 

 

 

and try again.

 

DO NOT press any button on the recorder or remote control while Auto Set Up is in progress.

 

АВТО УСТАНОВКА

 

 

On-Screen Display

ПОЖАЛУЙСТА, ПОДОЖДИТЕ

 

 

 

 

 

0

+

+

+

+

[MENU] : ВЫХОД

During Auto Set Up

"ПОЖАЛУЙСТА, ПОДОЖДИТЕ", blinks on the screen and "Auto" blinks on the front display panel.

TV Screen

When Auto Set Up is completed, the lowest position number will appear on the front display panel.

Front Display Panel

NOTES:

If you have connected your TV to the recorder with RF connection and the on-screen display appearing on UHF channel 36 looks distorted, refer to the front display panel.

If you want to set the tuner manually such as to add or skip channels, to swap channel positions, to fine-tune channels or to set station names (ID – p. 43), pg. 40 – 43.

If no sound accompanies the picture on some channels that have been stored by Auto Set Up, the TV system setting for those channels may be incorrect. Select the appropriate TV system for those channels. "TV System Selection – When you see the picture but hear no audio" on page 41.

Image 4
Contents HR-DD949EE Safety Precautions Do not place the recorderCheck Contents Basic ConnectionsSituate Recorder Connect Recorder to MainsAuto Set Up Nitial Sett IngsAuto Channel Set Front Display PanelLanguage Set Access Video Channel SET Mode EN Initial SettingsVideo Channel Set SET Video ChannelExit Video Channel SET Mode Select TV SystemWith AV Connection Major CountriesClock Set ENABLE/DISABLE ON-SCREEN Display On-Screen DisplaysPress Push JOG %Þ to 13 3Basic PlaybackFeatures PlaybackActivate FRAME-BY-FRAME Activate HIGH-SPEED SearchAdjust Tracking Override Automatic TrackingManually Return to AutomaticActivate Instant Review Activate RepeatActivate Spatializer SpatializerSoundtrack Selection During PlaybackSET A/B Code Switch RE-SUPPLY PowerActivate Scene Finder Stop Scene FinderAudio signal during TimeScan Time Scan IndicatorTimeScan Variable-Speed Search/ Reverse PlayTimeScan Audio TimeScanSpeed SP Speed LP Audio output Basic Recording Recording Features S.T. Picture System EN RecordingRecording Display Panel IndicationPlay Pause Setup EN Timer RecordingMake List of Stored Station Names Channel Positions Guide Program Number SetAccess Guide Prog SET Screen NumberClose Menu If you already know the Guide Program number for a stationTimer Recording On NextPress OK Repeat steps 1-5for each additional programme Press TIMER. The recorder turns off automaticallyPress MENU, then try again from step Regular Timer Programming Press Stop +/- to enter the time you want recording to stopEngage RECORDER’S Timer ModePress TV Prog + Access Mode SET Access ProgrammeRevise Programme InformationTimer Auto SP/LP TimerTimer Warning Engage Auto SP/LPTV Multi Brand Remote Control Control Your TV Using Additional ButtonsSET TV Brand Code TRY Operating TVSatellite Tuner Multi SET Satellite Tuner Brand CodeTRY Operating Satellite Tuner Satellite Tuner Brand CodeSET Recording DECK’S Input Mode Edit To Or From Another Video RecorderMake Connections Start Source PlayerIf another recorder has no 21-pin Scart connector PlayerRecorder Recorder PlayerEdit From a Camcorder SET RECORDER’S InputStart Camcorder Start RecorderSET Input Mode Locate Start PointEngage Audio Dubbing Start DubbingReset the Counter Locate END PointRecorder Your recorder Recorded tapeStart Editing Engage Insert EditingEND Insert Editing Access Jlip ID NO. SET Screen Interface Protocol ConnectorSET Jlip ID Number Return to Normal ScreenView Confirmation Screen Perform Auto Channel SETTuner SET Press Push JOG % twice Storing Channels ManuallyMajor Countries TV System Access Manual CH. SET Screen Select ItemDelete Channel Close ConfirmationSwitch Stations Perform TuningSelect NEW Station Select Channel toTV Station And ID List Station NameSet the TV to its AV mode If you are using the AV connectionSet the TV receiver to the Video Timer again RecordingOther Problems OubleshootingÄ remain lit on the display panel. Is there a problem? Questions and Answer S E NOpen the lid to access covered connectors and buttons IndexRear View How To Use Installing BatteriesEN Index Specifications Backup time becomes shorter as the units internal partsHR-DD949EE