JVC HR-DD840U Cable Box Control, Situate Controller, Attach Controller, Connect Cable BOX to VCR

Page 15

Cable Box Control

Suggested Location

EN15

This procedure is required if you receive your TV channels through a cable box (descrambler). The Controller allows the VCR to automatically switch the cable box channel during timer-recording. The Controller is effective for recording shows that have been programmed using VCR Plus+ (pg. 42) or On-Screen Timer Programming (pg. 44).

Situate And Connect

Controller

Place the cable box on top of the VCR. Attach the VCR's Controller to the top of the VCR with the Controller’s transmitter pointed towards the cable box’s remote sensor.

Attention:

The Controller can also control a DBS receiver. If both a cable box and a DBS receiver are used, position the controller so its signal reaches the remote control sensors of both the cable box and DBS receiver.

Cable box

Your VCR

Controller

 

 

(suggested locations)

 

Cable box

 

 

 

 

 

 

Controller

 

Transmitter

 

Connected to

Connected

ANTENNA IN

to VIDEO/

 

AUDIO IN

Your VCR

CABLE

BOX

SITUATE CONTROLLER

1 Place the Controller so that the path between its transmitter and the cable box’s remote sensor is unobstructed.

ATTACH CONTROLLER

2 Fasten securely using the supplied adhesive strip.

CONNECT CABLE BOX TO VCR

3 The connection method depends on the type of cable box you have.

If your cable box has AUDIO and VIDEO OUT connectors . . .

. . . connect them to the AUDIO and VIDEO IN connectors on your VCR; select the correct external input mode as described in step 4, 5, 9 11 on page 50

&51. Set the VCR to channel "AU" to use the cable box.

If your cable box doesn’t have AUDIO and VIDEO OUT connectors . . .

. . . connect the antenna output connector on the cable box to the ANTENNA IN connector on the rear of your VCR.

Set the VCR tuner to the same channel as the cable box RF output (see page 16 also).

NOTE:

When connecting your cable box refer to its instruction manual.

CONNECT CONTROLLER TO VCR

4 Connect to the CABLE BOX connector on your VCR.

About Your Cable Box

This VCR has two separate methods to control your Cable Box.

The VCR's Wireless Remote Control Unit can control your Cable Box.

This eliminates the need for a separate Cable Box Remote Control Unit.

The VCR's Controller can also control your Cable Box.

This allows the VCR to change your Cable Box's channel number during timer recording.

Each method must be set up separately. To set up the VCR's Remote Control unit, refer to page 56. To set up the Controller go to page 16.

Image 15
Contents HR-DD840U Do not place the VCR Dear CustomerGrounding or Polarization Power SourcesPower Cord Protection Power LinesReplacement Parts AccessoriesDamage Requiring Service CleaningContents Basic Connections Auto Clock Set/Auto Tuner Set Plug & Play SetupInitial Settings Plug & PlayLanguage Time Scan 5, then ClockSelect Screen PreparationSemi-Auto Select ModeAccess Select Screens Select Host ChannelMake Corrections Select D.S.T. ModeSelect Time Zone SET DATE, Time and D.S.TSET Access Main MenuAccess Tuner SET TunerInformation Store or Skip Desired Channel Access Tuner SET ScreenAccess AFC Screen Make SelectionConnect Cable BOX to VCR Cable Box ControlSituate Controller Attach ControllerSet Cable Box Output Channel Return to VCR PLUS+ SET-UP ScreenBrand SET Screen Access Cable BOXYou can now set up the VCR Plus+ feature pg Turn on Cable BOXVCR Plus+ Guide Channel Matching VCR Plus+ SetupCheck Input Data Access Custom SET Screen Input Receiving Channel NumberAccess VCR PLUS+ SET-UP Screen Access Guide Channel SET ScreenDBS Receiver Control Connect DBS Receiver to VCRDBS receiver PUT, then press OK Set DBS Receiver Output ChannelDBS Receiver Brand SET, then press OK Turn on DBS ReceiverEnter DBS Receiver Brand Set DBS Receiver BrandStart Playback Simple PlaybackLoad a Cassette Find Program Start PointSimple Recording Activate SLOW-MOTION Playback FeaturesPause During Playback Activate FRAME-BY Frame PlaybackRE-ENGAGE Automatic Tracking Engage Manual Tracking ModeAdjust Manual Tracking Layback and Recording FeaturesVideo Stabilizer Activate VideoStabilizer Return to NormalAccess Function SET Access SuperimposeSuperimpose Mix Access Audio SelectAccess Audio Monitor Select The SoundtrackInstant ReView Access Distant CodeStart Search Index SearchMemory Start RepeatStop Repeat Activate CounterAV Compu Link Playback Access SpecialMake Connection Function ScreenExample Enable AV Compu Link PlaybackPerform AV Compu Link Playback Or TimeAuto Picture Tape in use Press Play VCR adjusts Playback picture qualityPlayback Based on the qualityAudio signal during TimeScan TimeScanVariable-Speed Search/ Reverse Motion Playback Speed Audio output Skip Over Unwanted SectionsTimeScan Skip SearchCH or Time Scan Access TimescanAudio Screen TimeScan AudioSelect Channel for Viewing Recording FeaturesEngage TV Mode Reset Counter to ZeroTo Record Stereo Programs Access 2ND AudioStereo And SAP Second Audio Program To Record SAP ProgramsScan Hi-Fi Audio Recording Level ControlGUIDE. The MENU, REW VCR Plus+ Timer ProgrammingEN Timer Recording When Using The Illumi-Guide FeatureEngage Timer Mode CHECK/CORRECT InputData On-Screen Access Program SETTime SCAN, Cancel and Menu Time Scan , Cancel and MenuSET Program Information Check And Cancel Programs Cancel a ProgramRE-ENGAGE Timer Timer RecordingAccess Auto Timer Auto TimerOr, during on-screen timer programming Press REC on the front panel Instant Timer Recording ITREngage ITR Mode SET Recording DurationEdit To Or From Another Edit From a Camcorder ModePress CH or Time Scan Set your VCR to its record mode Access AUX Input ScreenIf you are connecting AV cable to the AV Set the camcorder to its play modeLocate Start Point SET Input ModeReset the Counter Locate END PointPress Insert Engage Insert EditingStart Editing END Insert EditingEND Audio Dubbing Audio Dubbing recorderEngage Audio Dubbing Start DubbingSET TV Brand Code SET Remote Control ModeSpecial Features Turn on the TVOperate Cable BOX Cable Box Multi-Brand Remote ControlTurn on the Cable BOX Enter Cable BOX BrandTurn on the DBS SET Remote ControlDBS Receiver Multi-Brand Remote Control CABLE/DBS/VCR switch to VCRTurn VCR Power on Unplug Vcrs PowerSET A/B Code Switch Plug in Power CordTroubleshooting E N TV/CABLE/DBS/VCR switch isCassette gets stuck partway Oubleshooting Timer againRe-perform the VCR Plus+ setup Doesn’t work properly When scanning channels, someResume recording Remote control won’t operate What happens if the tape runs out during recording? EN Questions and AnswersCan the VCR indefinitely remain in the still mode? Can the VCR indefinitely remain in the Record-Pause mode?Select DBS Receiver Output Channel MBR Multi-Brand Remote Code SettingIndex List Of TermsFront View Rear View How To Use Installing BatteriesSpecifications For Servicing Only in U.S.A HOW to Locate Your JVC Service CenterLimited Warranty Warranty Only in U.S.AEMO Memo HR-DD840U