– Other Functions –
VIDEO STABILIZER — ON/OFF
When this function is set to “ON”, you can automatically correct vertical vibrations in the picture when playing back unstable recordings made on another VCR.
NOTE:
To watch recordings with
BLUE BACK — ON/OFF
When this function is set to “ON”, the TV screen becomes all blue in the following cases:
●When receiving a channel not in use.
●When stopping playback.
NOTE:
When you want to receive an unstable channel with poor signals, set this function to “OFF”.
2ND AUDIO RECORD — ON/OFF
● When this function is set to “ON”;
If a SAP program is received, the SAP audio is recorded on both the normal and
If a
● When this function is set to “OFF”, the SAP audio cannot be recorded.
NOTES:
When the channel is changed on the VCR;
● The “STEREO” indication appears on the screen for about 5 seconds if the program is a stereo broadcast.
● The “SAP” indication appears on the screen for about 5 seconds if the program is a SAP broadcast.
● Both indications appear when a stereo program is accompanied by SAP sound.
AUDIO MONITOR — HI-FI/HI-FI L/HI-FI R/NORM/MIX
This VCR can record two sound tracks simultaneously (normal and
NORM: Sound on the normal track is played back.
MIX: Both sounds on the
NOTES:
●While playing back a monaural tape, sounds on the normal track will be heard regardless of this setting.
●If RF connection is used for viewing pictures on the TV, sound will be monaural even though you select
●You can also use the A. MONITOR button on the Remote to select the desired monitor sound.
Multi-Brand Remote Control
This Remote can control some functions of remote controllable TVs, cable boxes or DBS (Direct Broadcast Satellite) receivers listed below. Without setting, you can control a JVC TV.
NOTES:
●Some unit’s brands have more than one code. If the unit does not function with a specified code, try other codes.
●Depending on the type of unit, some or all functions cannot be operated using this Remote.
●It’s not possible to operate a unit not equipped with a remote sensor.
●It’s not possible to set the Remote for both your cable box and a DBS receiver at the same time.
●Once you have set the Remote to operate the unit, you do not have to set it until you replace the batteries from the Remote.
TV Brand Setting
ATurn on TV
Turn on the TV using the Power button on the TV or its Remote.
BSet TV brand code
APress and hold TV.
BPress MBR SET.
CPress the Number keys to enter your TV’s brand code.
DPress OK, and release TV. The TV should turn off.
COperate TV
While holding down TV, press one of the following buttons: POWER, TV/VCR, TV
●For some brands, you must press ENTER after having pressed the Number keys to enter a channel number.
TV BRAND | CODE | TV BRAND | CODE |
|
|
|
|
JVC | 01, 03 | SONY | 07 |
HITACHI | 10 | SAMSUNG | 12 |
MAGNAVOX | 02 | SANYO | 13 |
MITSUBISHI | 03 | SEARS | 13 |
PANASONIC | 04, 11 | TOSHIBA | 08 |
RCA | 05 | ZENITH | 09 |
SHARP | 06 |
|
|
Cable Box or DBS Receiver Brand Setting
ATurn on cable box or DBS receiver
Turn on the cable box or DBS receiver using the Power button on the unit or its Remote.
BEnter brand code
APress and hold CABLE/DBS.
BPress MBR SET.
CPress the Number keys to enter your cable box’s (or DBS receiver’s) brand code.
DPress OK, and release CABLE/DBS.
COperate cable box or DBS receiver
While holding down CABLE/DBS, press one of the following buttons: POWER, TV
●For some brands, you must press ENTER after having pressed the Number keys to enter a channel number.
●To change the cable box’s (or DBS receiver’s) channels, press TV CH+/– or the Number keys. (The CH+/– button can be used to change the VCR’s channels only.)