Menu Switches, Menu switch organization

3 CONNECTIONS

5 Edit adjust setting The No. 353 <EDIT ADJUST> menu switch must be adjusted according to the configuration of the editing system being used.

Setting table (when the RM-G800 is used)

For servicing

→See the service manual page 1-10 “1.6 SERVICE MENU”.

4 MENU SWITCHES

You can set menu switches using either the on-screen display or the counter display. To set switches on the on-screen display, you will need to connect a monitor to the VCR’s [VIDEO MONITOR OUT] connector. This section explains how to set switches using the on-screen display. The same procedures apply to switch setting on the counter display, the only difference being that each menu switch item is indicated by numeric code rather than by name.

Signal connection method	Player
Analog	BR-DV600
IEEE 1394	BR-DV600
Analog	BR-DV600

Setting

0 F

Recorder BR-DV600BR-DV600BR-S800

Setting

4 F

2 F

---

4-1 Menu switch organization

On-screen display

Analog	BR-DV600
Analog	BR-S800/BR-S500 (+ SA-N50)*

0 F

---

SR-S365 (U MODEL) SR-S388 (E MODEL)

BR-DV600

---

3 F

[SET]

STOP

TCR1 2 : 0 0 : 0 0 : 0 0

Menu switch group select screen

Pressing the [MENU] button with the normal screen displayed brings up the menu switch group select screen. Select the desired group with the [SHIFT +/–] button.

* To ensure the stability of input signals, install the SA-N50 in the BR-DV600.

[MENU] Menu switch group select screen

The selected group number blinks. Press the [SELECT] button to go to the selected group

5 Non-linear editing system Material recorded on a MiniDV tape can be captured to a non-linear editing system. The following non-linear editing systems are able to utilize Super Scene Finder (SSF) data.

•Canopus Corporation: DV Rex RT

•Casablanca

				Audio signal
	Video signal
DV
IN/OUT	COMPONENT
LINEVIDEO	COMPONENT		AUDIO
			CH 1/3 CH 2/4
Y/C			IN
IN	R-Y	B-Y	IN
	Y
			OUT
OUT			OUT
			MONITOR
			OUT
MONITOR			1 REMOTE	2
OUT	SYNC IN TIME CODE	SPARE	SERIAL
	TIMER			DC 12V
	REC	PLAY		DC 12V
	OFF

	0 0 0	:	SERVO / SYSTEM
	1 0 0	:	V I DEO
	2 0 0	:	AUD I O
	3 0 0	:	SYSTEM
[SHIFT]	4 0 0	:	T I ME CODE
[SHIFT]	5 0 0	:	ONSCREEN
	HM	:	HOUR METER

[SELECT]


Menu switch setting screen
0 0 2	: OPERAT I ON LOCK
		OF F
0 0 3	: SYNC SELECT
		AUTO
0 5 0	: REMOTE	SELECT
		J VC BUS+RS4 2 2A
1 0 8	: V I DEO	I NPUT SELECT
		L I NE

		[MENU]
	( HOUR METER )
DH	: DRUM HOUR METER
		0 0 0 0 0 0H

menu switch setting screen.

Menu switch setting screen

To access this screen, press the [SELECT] button on the menu switch group select screen. Press the [MENU] button to go to the menu switch group select screen.

Menu1 switch setting procedure

Press the [SHIFT –/+] button on the menu switch set- ting screen to select the menu switch you want to set. 2[The selected menu switch number blinks.

3Press the [SELECT] button to change the set value.

Remote control

Non-linear editing system

5 Control via the DV connector

• When the DV connector is used for control, assemble editing cannot be performed.

• When the VCR is stopped via the DV connector, a command error message may be returned to the controller. This is not

a malfunction.

On-screen display	Counter display
When entered
DATA SET
DATA SET
When data has not
When data has not
been entered yet
ABORT

4Repeat steps 1and 2to change any other menu switches.

Press the [SET] button to end menu switch setting. [The set value is entered and the normal screen is restored. When entering the data, the indications shown on the left are displayed. If data has not been entered and menu switch setting is ended, “Abort” indication is shown.

To access another group menu switch setting screen without ending menu switch setting, press the [MENU] button.

Notes on connecting a cable to the [DV IN/OUT] connector

Set the following menu switches, turn the connected equipment ON and then connect the cable to the [DV

IN/OUT] connector. (If two BR-DV600s are connected to each other, it is not necessary to turn them ON.)

Menu switch settings

•When used as a player

Set the No. 108 <VIDEO INPUT SELECT> menu switch to any position except “IEEE 1394”. (If this switch is currently set to “IEEE 1394”, change the setting and turn the power OFF and ON again.)

•When used as a recorder

Set the No. 108 <VIDEO INPUT SELECT> menu switch to “IEEE 1394”.

•When controlled by another device via the [DV INPUT] connector Set the No. 050 <REMOTE SELECT> menu switch to “IEEE 1394”.

Switching the

setting screen

[SHIFT] +/–: Item select

ADVANCE

PRESET

SHIFT

CH 1/3

OVER AUTO OFF DEW

HOLD

SHIFT

A. DUB

40 30 20

0 dB

CH 2/4

OVER SERVO RF

SELECT

SET

32k

48k

NDF

HOLD

AUD LOCK

MONITOR

OUTPUT

COUNTER

CH-1/2

CTL

MIX

CH-3/4

AUDIO

Menu switch display

SELECT: Changes the setting.

SET:

Enters the setting.

Menu switch setting screen

0 0 2 : OPERAT I ON

LOCK

OF F

[MENU]

0 0 3 : SYNC SE L ECT

[SHIFT]

AUTO

0 5 0 : REMOTE SE L ECT

J VC

BUS +RS 4 2 2 A

[SELECT]

[SET]

0 0 0 ~

SERVO / SYSTEM

1 0 0 ~

V I DEO

2 0 0 ~

AUD I O

3 0 0 ~

SYSTEM

4 0 0 ~

T I ME CODE

[MENU]

5 0 0 ~

: ONSCREEN

: HOUR METER

STOP

TCR

1 2 : 0 0 : 0 0 : 0 0

Menu switch group

select screen