For servicing
→See the service manual page
12 TROUBLESHOOTING |
12 TROUBLESHOOTING
|
| ||
If the unit malfunctions during operation, the | |||
message on the monitor and/or the counter display. Also, the [AUTO OFF] indicator may be shown on the LCD. In this case, | |||
turn the power off and then on again to restore operation. If the [AUTO OFF] indicator appears again, the VCR may require | |||
repair or adjustment. Consult your local JVC dealer. |
|
| |
The VCR’s | |||
case, turn the main power (AC and DC power supplies) off, turn on again and check the operation. | |||
Error contents | Operation | Solution | |
Counter display |
|
|
|
SUP REEL FAILURE ERR7202~ 7203
TAKE UP REEL FAILURE ERR7302~ 7303 SYSCON REF ERROR ERR8400
Error contents
The supply reel rotation is abnormal.
The takeup reel rotation is abnormal.
System controller reference signal failure.
Operation
Operation stops. No operations are possible.
Operation stops. No operations are possible.
Solution
Turn the power on again. In some cases, the tape may be damaged, so use a different tape. If the problem persists, consult your JVC dealer.
Turn the power on again.
CONDENSATION ON DRUM
The [DEW] indicator lights.
FAILURE LOADING
ERR3200
Condensation on the drum. | • When a cassette is not |
| loaded, the drum starts to |
| rotate. |
| • When a cassette is loaded, |
| the AUTO OFF mode is |
| engaged and the operation |
| stops. |
Tape cannot be loaded. | Operation stops. No |
| operations are possible. |
Wait for the drum to stop rotating, then load a cassette.
Do not use the unit until the AUTO OFF mode is disengaged.
Turn the power on again. In some cases, the tape may be damaged, so use a different tape. If the problem persists, consult your JVC dealer.
PC TAPE INHIBIT
Pc7APE
LP INHIBIT
LPiNh
REC INHIBIT
REciNh
1394 INHIBIT
A data tape for personal computer is used.
A tape recorded in the LP mode is played back.
The cassette’s safety slide is set to “SAVE”.
No signal is input to the [DV IN/OUT] connector.
Operation continues.
Operation stops.
Operation stops.
Operation stops.
Use a tape on which NTSC (U MODEL), PAL (E MODEL) signals are recorded.
Use a tape recorded in the SP mode.
Set the safety slide to “REC”.
Input signals to the [DV IN/ OUT] connector.
FAILURE UNLOADING ERR3300 CASSETTE EJECT FAILURE ERR4100 HOUSING FAILURE ERR4200 TAPE DEFECTIVE ERR5605 TAPE DEFECTIVE ERR5607 END LEADER DETECTION ERR5702
BEGIN LEADER DETECTION ERR5802 DRUM MOTOR FAILURE
•Tape cannot be unloaded.
•Tape is jammed.
The eject operation is abnormal.
The cassette housing is abnormal.
The tape ends.
The tape is slack.
The tape end sensor is abnormal.
The tape beginning sensor is abnormal.
The drum rotation stops.
1394iNh
EE CHECK INHIBIT
EEiNh
AUDIO DUB INHIBIT
ADBiNh
SSF INHIBIT SSFiNh FAN MOTOR FAILURE FAN STOP
When the IEEE 1394 input is selected, the EE check is performed.
The cassette’s safety slide is set to “SAVE”. The tape was recorded with the 48 kHz sampling rate. The No. 245 <SAMPLING RATE> menu switch is set to “48K”. Audio dubbing was attempted on a tape recorded in the LP mode.
SSF data error occurs.
The fan motor stops.
Operation continues.
Operation stops.
Operation continues.
Operation stops about 60 seconds after the fan motor stops (with the No. 397 <FAN STOP SHUTDOWN> menu switch set to “ENABLE”).
When the IEEE 1394 input is selected, the EE check cannot be performed.
Set the safety slide to “REC”. Use a tape recorded at the 32 kHz sampling rate. Set the No. 245 <SAMPLING RATE> menu switch to “32K”. Audio dubbing cannot be performed on tapes recorded in the LP mode.
Use a tape on which SSF data has been properly recorded.
Consult your nearest JVC dealer.
ERR7001
CAP MOTOR FAILURE ERR7101
The capstan rotation stops.
|
|
| HEAD CLOG |
| The video head is clogged. | |||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
HEAD CLOG |
|
| ||||||||||||
The operation continues.
Clean with a dedicated head cleaning tape. Refer to the separate enclosure, “Notes on the use of a cleaning tape”.
40 | 41 |