4 MENU SWITCHES | |
| |
For switch setting procedures, refer to “Menu switch setting | |
procedure”. | |
q: | Factory setting |
(00): The number in the bracket shows the set value on the | |
| counter display. |
002OPERATION LOCK
Details: Switches the operation lock ON/OFF. Setting:
qOFF (00): The operation lock is OFF: all operations are enabled.
ON (01): The operation lock is ON: all controls are disabled except for the [MENU] button.
003SYNC SELECT
Details: Selects the sync signal during play. Setting:
EXTERNAL (01): Synchronizes with the signal input
to the [SYNC IN] connector.
qAUTO (03): Switches the synchronization automatically depending on whether or not a signal is input to the [SYNC IN] connector. For details, refer to page 11.
050REMOTE SELECT
Details: Selects the remote controller connected to the [REMOTE] connector on the rear panel. When the optional
Setting:
IEEE 1394 (01): Allows control of this unit with the | |
| controller connected to the [DV IN/ |
RS422A (04): | OUT] connector. |
Allows control of this unit with the | |
| controller connected to the |
| [REMOTE 1] connector. |
IEEE 1394 + RS422A (05): Allows control of this | |
| unit with the controllers connected |
| to the [DV IN/OUT] and [REMOTE 1] |
| connectors. |
JVC BUS (08): Allows control of this unit with the | |
| controller connected to the |
| [REMOTE 2] connector. |
JVC BUS + IEEE 1394 (09): Allows control of this | |
| unit with the controllers connected |
| to the [REMOTE 2] and [DV IN/ |
| OUT] connectors. |
JVC BUS + RS422A (12): Allows control of this unit | |
| with the controllers connected to |
| the [REMOTE 2] and [REMOTE 1] |
| connectors. |
qJVC BUS + RS422A + 1394 (13): Allows control of this unit with the controllers connected to the [REMOTE 2], [REMOTE 1] and [DV IN/OUT] connectors.
(When the optional | |
board is installed) | |
IEEE 1394 (01): Allows control of this unit with the | |
| controller connected to the [DV IN/ |
RS232C (02): | OUT] connector. |
Allows control of this unit with the | |
| controller connected to the |
| [REMOTE 1] connector. |
IEEE 1394 + RS232C (03): Allows control of this | |
| unit with the controllers connected |
| to the [DV IN/OUT] and [REMOTE 1] |
| connectors. |
JVC BUS (08): Allows control of this unit with the | |
| controller connected to the |
| [REMOTE 2] connector. |
JVC BUS + IEEE 1394 (09): Allows control of this | |
| unit with the controllers connected |
| to the [REMOTE 2] and [DV IN/ |
| OUT] connectors. |
JVC BUS + RS232C (10): Allows control of this unit | |
| with the controllers connected to |
| the [REMOTE 2] and [REMOTE 1] |
| connectors. |
qJVC BUS + RS232C + 1394 (11): Allows control of this unit with the controllers connected to the [REMOTE 2], [REMOTE 1] and [DV IN/OUT] connectors.
108VIDEO INPUT SELECT
Details: Selects the input video signal. Setting:
qLINE (00): Selects video signals input to the
Y/C (01): | [LINE IN] connector. |
Selects video signals input to the | |
| [Y/C IN] connector. |
COMPONENT (02): Selects video signals | |
| input to the [COMPONENT IN] |
| connector. |
IEEE 1394 (03): Selects video and audio signals | |
| input to the [DV IN/OUT] |
| connector. In this case, analog |
| audio signals are not input. |
125SETUP (U MODEL)
Details: Sets whether or not the setup is applied to the analog video signals (composite, Y/C, component).
Setting:
OFF (00): Does not apply the setup.
qON (01): Applies the setup. Set to this position to play back a tape recorded on the GY- DV500.
Notes:
•This setting affects recording and playback of analog video signals.
•Picture hue and brightness can be affected if dubbing is repeated without applying a setup suitable to video signals.
4 MENU SWITCHES | |
q: | Factory setting |
(00): The number in the bracket shows the set value on the | |
| counter display. |
212AUDIO OUT AT SEARCH
Details: Selects whether or not audio is output to the [AUDIO OUT] and [AUDIO MONITOR OUT] connectors and headphones jack during search at speeds above ±1x.
Setting:
OFF (00): No output. qON (01): Audio is output.
214V. FADE
Details: Switches the V. fade function ON/OFF. V.fade reduces audio noise at the tag recording during playback.
Setting:
OFF (00): The V. fade function is not activated. qON (01): Activates the V. fade function.
245SAMPLING RATE
Details: Selects the sampling rate frequency when recording audio digitally.
Setting:
32K (00): Records signals at a 32 kHz sampling frequency. Set to this position for audio dubbing on CH3 and CH4.
q48K (01): Records signals at a 48 kHz sampling frequency. Audio dubbing is not possible with this setting.
311AUTO PLAY
Details: Selects whether or not playback starts automatically after the tape is rewound to the beginning.
Setting:
qSHORT FF (00): The tape stops after short FF.
PLAY (01): | Auto play does not start. |
Auto play starts. Repeat playback | |
| is available when No. 312 <AUTO |
| REW> menu switch is set to “ON”. |
312AUTO REW
Details: Selects whether or not the tape is rewound automatically at tape end during recording or playback.
Setting:
qOFF (00):The tape is not rewound automatically. ON (01): The tape is rewound automatically.
Repeat playback is available when No. 311 <AUTO PLAY> menu switch is set to “PLAY”.
353EDIT ADJUST
Details: When this unit is used with an editing controller and the
Switch setting differs depending on the configuration of the editing system. For details, refer to “Edit adjust setting” on page 16.
Setting:
q0F: No compensation.
1F: | The playback start point is delayed by 1 frame. |
2F: | The playback start point is delayed by 2 frames. |
3F: | The playback start point is delayed by 3 frames |
4F: | to the factory set timing. |
The playback start point is delayed by 4 frames. | |
5F: | The playback start point is delayed by 5 frames. |
6F: | The playback start point is delayed by 6 frames. |
7F: | The playback start point is delayed by 7 frames. |
360AUTO REW AT TIMER
Details: Selects whether or not the tape is automati- cally rewound when the VCR power is switched ON in the Timer Play or Recording Standby mode.
Setting:
qOFF (00): Playback or recording starts immedi- ately. The tape is not rewound.
ON (01): Playback or recording starts after the tape is rewound to the beginning.
363CONTROLLER SELECT
Details: Selects the setting according to the type of remote control unit connected via the RS- 422A interface.
Setting:
qTYPE 1 (00): For the
TYPE 2 (01): For a
TYPE 3 (02): Unused.
:
TYPE 8 (07)
396BATTERY SELECT
Details: When using DC power, set this switch according to the DC power supply and battery type.
Setting:
q12 V (00): Select this setting to use a DC power supply
13.2V (01): Select this setting to use Anton Bauer Inc.’s Trimpack 13, ProPac 13.
14.4V (02): Select this setting to use Anton Bauer Inc.’s Trimpack 14, ProPac 14 and IDX Corporation's
18
For servicing See the service manual page
19