Magnavox VRB613AT Timer Recording cont’d, Time OFF To Correct Push Clear To END Push Exit

Page 34

34 Timer Recording (cont’d)

4

Use the Number buttons (1 - 8) to select a slot in which to store the timer recording. There are eight slots. Numbers for open slots will flash on the screen.

NOTE: If you enter a number for a slot that has already been used to store a timer recording, PREVIOUSLY SET PROGRAM will appear on the screen briefly. Information about the program in that slot will appear on the screen. If this happens, press the STATUS/EXIT button, then select another number.

5

Use the Number buttons to enter the channel you want to record.

●Cable Users, enter channel numbers as a two-digit number for the quickest results. For example, to select channel 6, press

0,6. If you only press the Number 6 button, channel 6 will be selected after a brief delay. There also may be a brief delay when you select channels 10, 11, and 12. If you want to select chan- nels 100 and above, enter channel numbers as a three-digit number. For example, to select channel 117, press 1, 1, 7. Antenna Users, enter channel numbers as a two-digit number for the quickest results. For example, to select channel 5, press 0,5. If you only press the Number 5 button, channel 5 will be selected after a brief delay.

●If you are recording from line input, press 0,0 to select AV REAR.

●If you are using a Cable Box/DBS, select the Cable Box/DBS output channel (03 or 04). Set the Cable Box/DBS to the chan- nel you want to record. Leave the Cable Box/DBS on for the timer recording. See page eight for details.

6

Press two Number buttons for the hour you want the recording to begin. Press two Number buttons for the minute you want the recording to begin. Press 1 for AM or 2 for PM. For example, for 9:30 PM, press 09, 30, 2.

ONE TIME PROGRAM

PROGRAM

1

CHANNEL

10

TIME ON

– – : – –

TO CORRECT PUSH CLEAR

TO END PUSH EXIT

7

Follow the instructions in step 6 to enter the recording’s stop time. (AM or PM will be set automatically.)

ONE TIME PROGRAM

PROGRAM

1

CHANNEL

10

TIME ON

09:30 PM

TIME OFF

– – : – –

TO CORRECT PUSH CLEAR

TO END PUSH EXIT

4-7

POWER

VCR/TV

 

EJECT

VCR

TV

 

CBL/DBS

 

PLAY

 

 

REW

 

 

F.FWD

 

STOP

 

 

MENU

STATUS/EXIT

CLEAR

1

2

3

 

4

5

6

CH

 

7

8

9

 

ENTER

ALT. CH

0VOL

SPEED

TIME SEARCH

PAUSE/STILL

 

REC/OTR

MEMORY

SLOW

MUTE

Helpful Hints

•Entries that do not match the VCR’s clock or calendar will cause a ques- tion mark to appear on the screen.

•If you are recording from line input, connect the audio and video cables to the AUDIO IN and VIDEO IN jacks on the back of the VCR. (Please see illustration on page 37.)

Page 33 Page 35
Image 34
Page 33 Page 35
Contents VRB413AT VRB613AT This bolt of lightning indi- cates uninsulated material Dear Philips product ownerFor Customer Use Model No Serial NoIntroduction FeaturesSafety Precautions Declaration of ConformityTable of Contents Before Using Your VCR Hookups without a Cable Box/Direct Broadcast System Disconnect the antenna or cable from your TVHookups without a Cable Box/Direct Broadcast System cont’d Plug in the TV and the VCRConnections Hookups with a Cable Box/Direct Broadcast SystemRecording/Viewing Any Channel Recording One Channel/Watching Another Cable Signal Cable Box/DBSTV’s Antenna VRB613 Hookups with a Stereo TVVRB413 2Turn on the TV Press the VCR button, then press the Power buttonTurning on Your VCR Press the Menu button. The display shown below will appearPress the VCR button Press the Menu button Automatic Channel SetupVRB613 only Adding/Deleting Channels Automatic Channel Setup cont’dPress the STATUS/EXIT button Reviewing Memorized Channels Press the STATUS/EXIT button once or twice to exitManual Clock Setting Setting the ClockDo each step within 60 seconds of the previous step Setting the Clock cont’d Enter a 0 before a single-digit numberAutomatic Clock Setting Press the VCR button, then press the Menu buttonTime Zone Daylight-Savings Time Press the VCR buttonLanguage Selection Setting the Remote to Operate a TV Your VCR remote control may operate your TV. If the remote2Find Your codeEject Button Remote Control ButtonsVOLume o/p Button Press to adjust the volume of your TV VCR ButtonTV Button Remote Control Buttons cont’dPress to operate the TV If you select Status ON, then select Counter only on On-Screen Status DisplaysStatus Display example only If you select Status ON, then select Counter only OFFCassette Compartment Timer LightVCR Display Panel VCR LightRemote Sensor Power ButtonFWD Fast Forward Button REWind ButtonRear Panel Read and follow the steps below to play a tape PlayingVHS Quasi Play Back Sqpb 1Turn on the TV 2Insert a tape in the VCRVCR light does not appear, press the VCR/TV button once RecordingIf the VCR light appears on the display panel, go to . If RECord light will appear Recording One Channel/Watching Another One-Touch Recording OTR CH12Timer Recording DailyTimer Recording cont’d Time OFF To Correct Push Clear To END Push ExitPress the STATUS/EXIT button. Program WAS COM Tape SpeedsChecking or Cancelling Timer Recordings Rerecording Tape Duplication RF coaxial cableRepeat Play VCR SET UP, then press the F.FWD/B buttonPress the F.FWD/B button so that on appears beside Real-Time Counter Memory Press the STATUS/EXIT button to see the status displayTime Search Press the VCR button Press the Time Search buttonSuper High Speed Searching LP/SLP Special Effects PlaybackForward and Reverse Searching SP/LP/SLP Viewing a Still PictureAutomatic Operation Features Specifically… Understanding On-Screen DisplaysMonitor Multi-Channel Television Sound System VRB613 only cont’d Press the RECord/OTR button to start recordingHi-Fi Stereo Sound System VRB613 only Blue Background Helpful Hints Helpful Hints cont’d Glossary Cable Box/DBS Output Channel 03 orSpecifications Limited Warranty Index Page Page Page Supplied Accessories
Top Page Image Contents