Magnavox VRB613AT, VRB413AT owner manual Specifications

Page 50

50 Specifications

Video Heads

Four heads – Hi-Fi (VRB613)

Four heads (VRB413)

Video Signal

EIA standards; NTSC color

Antenna

VHF/UHF – 75 ohm external antenna terminal

VHF Output Signal

Channel 03 or 04 (switchable) 75 ohms unbalanced

Power Requirement

120V AC; 60Hz

Power Consumption

14W (VRB613)

12W (VRB413)

Operating Temperature

41°F (5°C) to 104°F (40°C)

Relative Humidity

10% to 80%

Weight

5.5lbs. (2.5 kg.) (VRB613)

5.3Ibs. (2.4 kg.) (VRB413)

Dimensions

14-3/16” (W) x 3-5/8” (H) x 8-3/4” (D) (360mm x 92mm x 223mm)

Tuner Broadcast Channels

VHF 2-13, UHF 14-69

Cable TV Channels

1-125

NOTE: Designs and specifications are subject to change without notice.

Image 50
Contents VRB413AT VRB613AT This bolt of lightning indi- cates uninsulated material Dear Philips product ownerFor Customer Use Model No Serial NoIntroduction FeaturesSafety Precautions Declaration of ConformityTable of Contents Before Using Your VCR Hookups without a Cable Box/Direct Broadcast System Disconnect the antenna or cable from your TVHookups without a Cable Box/Direct Broadcast System cont’d Plug in the TV and the VCRRecording/Viewing Any Channel Hookups with a Cable Box/Direct Broadcast SystemConnections TV’s Antenna Cable Signal Cable Box/DBSRecording One Channel/Watching Another VRB413 Hookups with a Stereo TVVRB613 2Turn on the TV Press the VCR button, then press the Power buttonTurning on Your VCR Press the Menu button. The display shown below will appearVRB613 only Automatic Channel SetupPress the VCR button Press the Menu button Press the STATUS/EXIT button Automatic Channel Setup cont’dAdding/Deleting Channels Reviewing Memorized Channels Press the STATUS/EXIT button once or twice to exitDo each step within 60 seconds of the previous step Setting the ClockManual Clock Setting Setting the Clock cont’d Enter a 0 before a single-digit numberAutomatic Clock Setting Press the VCR button, then press the Menu buttonTime Zone Daylight-Savings Time Press the VCR buttonLanguage Selection Setting the Remote to Operate a TV Your VCR remote control may operate your TV. If the remote2Find Your codeEject Button Remote Control ButtonsVOLume o/p Button Press to adjust the volume of your TV VCR ButtonPress to operate the TV Remote Control Buttons cont’dTV Button If you select Status ON, then select Counter only on On-Screen Status DisplaysStatus Display example only If you select Status ON, then select Counter only OFFCassette Compartment Timer LightVCR Display Panel VCR LightRemote Sensor Power ButtonFWD Fast Forward Button REWind ButtonRear Panel Read and follow the steps below to play a tape PlayingVHS Quasi Play Back Sqpb 1Turn on the TV 2Insert a tape in the VCRVCR light does not appear, press the VCR/TV button once RecordingIf the VCR light appears on the display panel, go to . If RECord light will appearRecording One Channel/Watching Another One-Touch Recording OTR CH12Timer Recording DailyTimer Recording cont’d Time OFF To Correct Push Clear To END Push ExitPress the STATUS/EXIT button. Program WAS COM Tape SpeedsChecking or Cancelling Timer Recordings Rerecording Tape Duplication RF coaxial cablePress the F.FWD/B button so that on appears beside VCR SET UP, then press the F.FWD/B buttonRepeat Play Real-Time Counter Memory Press the STATUS/EXIT button to see the status displayTime Search Press the VCR button Press the Time Search buttonSuper High Speed Searching LP/SLP Special Effects PlaybackForward and Reverse Searching SP/LP/SLP Viewing a Still PictureAutomatic Operation Features Monitor Understanding On-Screen DisplaysSpecifically… Multi-Channel Television Sound System VRB613 only cont’d Press the RECord/OTR button to start recordingHi-Fi Stereo Sound System VRB613 only Blue Background Helpful Hints Helpful Hints cont’d Glossary Cable Box/DBS Output Channel 03 orSpecifications Limited Warranty Index Page Page Page Supplied Accessories