Magnavox VRB413AT, VRB613AT owner manual Rerecording Tape Duplication, RF coaxial cable

Page 37

Rerecording (Tape Duplication) 37

The instructions on this page show you how to copy tapes. The illustration uses two VRB613 VCRs. Different VCRs may operate differently. To duplicate a tape, make the connections shown, then follow steps 1-7.

1.Audio cables from AUDIO OUT Jacks of VCR 1 to AUDIO IN Jacks of VCR 2

VCR 1

Playing VCR

		VCR 2 - Recording VCR
AUDIO ANT			AUDIO ANT
L		IN	L		IN
L			L
OUT	IN		OUT	IN
R			R
VIDEO		OUT	VIDEO		OUT
OUT	IN CH3 CH4		OUT	IN CH3 CH4
					3. RF coaxial cable
		2. Video cable from VIDEO OUT Jack			from the OUT jack of
		2. Video cable from VIDEO OUT Jack			VCR 2 to the TV’s
		of VCR 1 to VIDEO IN Jack of VCR 2			ANTENNA IN Jack

●Audio and Video cables are not supplied.

1

Make the connections shown above.

2

VCR 1 will play your tape. Put a prerecorded tape in VCR 1.

3

VCR 2 will record your tape. Insert a blank tape in VCR 2. The VCR must be in VCR position. (The VCR light will appear on the display panel. If it does not, press the VCR/TV button once.)

4

Turn on the TV and set it to channel 03 or 04, whichever channel the CH3/CH4 switch on VCR 2 is set to.

5

Point the remote control at VCR 2. Press the VCR but- ton, then press Number buttons 0, 0, 1 or 0, 0, 2. (See Helpful Hints at right.)

6

Press the SPEED button to select SP or SLP at VCR 2.

7

Press the PLAY button on VCR 1 and the REC(ord)/OTR button on VCR 2 at the same time.

To stop recording, press the STOP/EJECT button on VCR 1, then press the STOP/EJECT button on VCR 2.

Helpful Hints

•If you use the AUDIO and VIDEO IN Jacks on the back of VCR 2, press Number buttons 0, 0, 1. AV REAR will appear on the screen. (Blue Background should be set to ON. Details are on page 46.)

•If you use the AUDIO and VIDEO In Jacks on the front of VCR 2, press Number buttons 0, 0, 2. AV FRONT will appear on the screen. (Blue Background should be set to ON. Details are on page 46.)

•Unauthorized recording of copy- righted television programs, video tapes, or other materials may infringe on the rights of copyright owners and violate copyright laws.

•If a program has copyright protec- tion, it may not record clearly.

•These instructions show you how to copy tapes using two VCRs like yours. Different VCRs may operate differently.

•The VCR in the figure above is the VRB613. If you have the VRB413, use a single-plug audio cable to con- nect the AUDIO OUT jack on VCR

1 to the AUDIO IN jack on VCR 2.

Image 37

Contents VRB413AT VRB613AT For Customer Use Dear Philips product ownerThis bolt of lightning indi- cates uninsulated material Model No Serial NoSafety Precautions FeaturesIntroduction Declaration of ConformityTable of Contents Before Using Your VCR Disconnect the antenna or cable from your TV Hookups without a Cable Box/Direct Broadcast SystemPlug in the TV and the VCR Hookups without a Cable Box/Direct Broadcast System cont’dConnections Hookups with a Cable Box/Direct Broadcast SystemRecording/Viewing Any Channel Recording One Channel/Watching Another Cable Signal Cable Box/DBSTV’s Antenna VRB613 Hookups with a Stereo TVVRB413 Turning on Your VCR Press the VCR button, then press the Power button2Turn on the TV Press the Menu button. The display shown below will appearPress the VCR button Press the Menu button Automatic Channel SetupVRB613 only Adding/Deleting Channels Automatic Channel Setup cont’dPress the STATUS/EXIT button Press the STATUS/EXIT button once or twice to exit Reviewing Memorized ChannelsManual Clock Setting Setting the ClockDo each step within 60 seconds of the previous step Enter a 0 before a single-digit number Setting the Clock cont’dPress the VCR button, then press the Menu button Automatic Clock SettingTime Zone Press the VCR button Daylight-Savings TimeLanguage Selection Your VCR remote control may operate your TV. If the remote Setting the Remote to Operate a TVYour code 2FindVOLume o/p Button Press to adjust the volume of your TV Remote Control ButtonsEject Button VCR ButtonTV Button Remote Control Buttons cont’dPress to operate the TV Status Display example only On-Screen Status DisplaysIf you select Status ON, then select Counter only on If you select Status ON, then select Counter only OFFVCR Display Panel Timer LightCassette Compartment VCR LightFWD Fast Forward Button Power ButtonRemote Sensor REWind ButtonRear Panel VHS Quasi Play Back Sqpb PlayingRead and follow the steps below to play a tape 1Turn on the TV 2Insert a tape in the VCRIf the VCR light appears on the display panel, go to . If RecordingVCR light does not appear, press the VCR/TV button once RECord light will appearRecording One Channel/Watching Another OTR CH12 One-Touch RecordingDaily Timer Recording Time OFF To Correct Push Clear To END Push Exit Timer Recording cont’dTape Speeds Press the STATUS/EXIT button. Program WAS COMChecking or Cancelling Timer Recordings RF coaxial cable Rerecording Tape DuplicationRepeat Play VCR SET UP, then press the F.FWD/B buttonPress the F.FWD/B button so that on appears beside Press the STATUS/EXIT button to see the status display Real-Time Counter MemoryPress the VCR button Press the Time Search button Time SearchForward and Reverse Searching SP/LP/SLP Special Effects PlaybackSuper High Speed Searching LP/SLP Viewing a Still PictureAutomatic Operation Features Specifically… Understanding On-Screen DisplaysMonitor Press the RECord/OTR button to start recording Multi-Channel Television Sound System VRB613 only cont’dHi-Fi Stereo Sound System VRB613 only Blue Background Helpful Hints Helpful Hints cont’d Cable Box/DBS Output Channel 03 or GlossarySpecifications Limited Warranty Index Page Page Page Supplied Accessories