Sherwood CDC-690T operating instructions Troubleshooting Guide, Problem Possible Cause Remedy

Page 24

ENGLISH

Troubleshooting Guide

If your unit should not perform as expected, consult the table below to see if the problem can be corrected before seeking help from your dealer or our service organization.

PROBLEM

POSSIBLE CAUSE

REMEDY

 

 

 

No power

• The AC input cord is disconnected.

• Connect the cord securely.

 

• The POWER switch is not pressed

• Press the POWER button to ON.

 

correctly.

 

 

 

 

No play

• The disc is loaded upside down.

• Reload the disc with the printed side

 

 

up.

 

• Dirty disc.

• Clean the disc.

 

• Defective or deeply scratched disc.

• Load another disc.

 

 

 

No sound

• Incorrect connections.

• Make connections correctly.

 

• Incorrect operation of the amplifier.

• Operate the amplifier correctly.

 

• The " " indicator lights up.

• Press the PLAY or PAUSE button to

 

 

cancel the pause mode.

 

 

 

Poor or distorted sound

• The unit is connected to the PHONO

• Make connections correctly.

 

input jacks of the amplifier.

 

 

• Poor connections.

• Check the connections and connect

 

 

all cords securely.

 

 

 

Sound skips

• Defective or deeply scratched disc.

• Play another disc.

 

• This unit is placed on a surface that is

• Place this unit on a stable surface.

 

subject to vibration or physical shock.

 

 

 

 

Programming or deleting

• The disc is dirty or badly scratched.

• Try again with a scratch-free disc.

does not perform.

• The programming or deleting

• Try again.

 

procedure is not correct.

 

 

• The number of the programmed

• Check the number of the

 

selections is 32.

programmed selections.

 

 

 

“Error” is displayed.

• Incorrect operation.

• Press the OPEN/CLOSE button to

 

 

open and close the disc tray or press

 

 

the POWER switch to turn the power

 

 

off and on.

 

 

 

2 4

Page 23 Page 25
Image 24
Page 23 Page 25
Contents CDC-690T Introduction For Your Safety Read this Before OperatingContents Rear Panel Connections Model NO. CDC-690TFront Panel & Remote Controls Remote ControlsThis receives the signals from the remote control Load a compact disc on the disc trayPress this button to open or close the disc tray Press this button to play tracks on CDs in random sequenceFluorescent Display Remote Control Operation Range PolarityBefore Operation Turn the power on Load the discs and close the disc tray Indicator lights up when the number of tracks isOperations To stop playChanging Discs During Skip and Search PlaySelecting a disc Searching for a passage during playPlaying Tracks in Random Sequence Playing the First 10 Seconds of Each TrackRepeat Play Repeating a single track during playRepeating a specific passage during PlayStop mode, enter the program mode Select the desired disc Example When selecting the discPlaying Tracks in ANY Sequence Programming the tracks on the CDsChecking the programmed selections Rectifying any wrong programmed selectionFind the desired selection and clear it in the program mode Clearing the programmed selectionsOpening the disc tray clears all programmed selections, too Stop mode, select the auto edit Mode Editing for RecordingMaking auto edit Tracks to be recordedStop mode, select the manual edit Mode Making manual editSelecting a Brightness Checking the edited tracksClearing all edited tracks Deleted Play If the DELETE/REVIEW button is pressed withoutSelecting a track, the selected disc is deleted as a Selected track is deleted automatically withoutRecovering the deleted selections Find the desired track and recover it in the delete modeOpening the disc tray recovers all deleted selections, too Checking the deleted selectionsUsing the Headphones Selecting a Time DisplayTroubleshooting Guide Problem Possible Cause RemedySpecifications 5707-04725-009-0
Top Page Image Contents