Sylvania DVC800CC owner manual Automatic Channel SET UP, To Select a Desired Channel

Page 17

SETUP

AUTOMATIC CHANNEL SET UP

VCR

The DVD/VCR can automatically program the tuner to scan only the channels which are available in your area.

¡Channel memory programming is NOT needed when the DVD/VCR is connected to a cable box or a satellite box as in "DVD/VCR TO TV CONNEC- TION" on page 14. In this case, set the CH3/CH4 Switch (which is located on the back of your VCR) to either CH3 or CH4, whichever is not used for nor- mal broadcasts in your area. Then set your TV to the same channel. The channel you want to record or view will be selected from the cable or the satellite box.

¡Follow the steps below once. Repeat only if there is a power failure or if the DVD/VCR is unplugged for more than 30 seconds. (In these cases, the pro- grammed channels are erased.)

¡You must follow the steps below before attempting to play or record a video tape.

1You need to connect the antenna or cable to the DVD/VCR first. Then, connect the DVD /VCR power plug to a standard AC outlet.

2Turn on the TV and set the TV to channel 3 or 4.

¡Now set the CH3/CH4 switch on the back of the DVD/VCR to match the channel selected on the TV.

3Turn on the DVD/VCR by pressing the POWER button. Both the POWER and the VCR/TV light will come on.

4Select the On Screen Language (“ENGLISH”,

“FRANCAIS” or “ESPAÑOL”) by pressing the PLAY or the STOP button.

Then, press the F.FWD but- ton.

5Begin channel preset by pressing the F.FWD button once. The tuner scans and memorizes all active channels in your area.

¡The DVD/VCR distinguishes

CH 01

between standard TV channels

 

and cable channels.

AUTO SET UP

 

6After scanning, the tuner stops on the lowest memorized channel. The TV screen returns to TV mode.

¡If “AUTO SET UP” appears on the TV screen again, check the cable connections. Press the F.FWD but- ton once again and the DVD/VCR will begin preset again.

TO SELECT A DESIRED CHANNEL

You can select the desired channel by using the CHANNEL(o/p) buttons or by directly pressing the Number buttons on the remote control.

Note for using the Number buttons:

¡When selecting cable channels which are higher than 99, press [+100] first, then press the last two digits.

¡You must precede single-digit channel numbers with a zero (For example: 02, 03, 04 and so on).

TO PRESET THE CHANNELS AGAIN

1Press the MENU button until the main menu appears. (If you have already set the clock, you only have to press it once. If not, you have to press it twice).

2Select “CHANNEL SET UP” by pressing the PLAY or the STOP button. Then, press the F.FWD button.

3Select “TV” or “CATV” by pressing the PLAY or the STOP button. Then, press the F.FWD button.

¡After scanning, the tuner stops on the lowest memo- rized channel.

– 17 –

EN

1L25

Page 16 Page 18
Image 17
Page 16 Page 18
Contents DVC800CC Laser Safety Important Safeguards Symbols Used in this Manual Supplied AccessoriesAbout Copyright Refers to playback of video cassette tapesTable of Contents DVD Mode FeaturesInstallation Location PrecautionsAvoid the Hazards of Electrical Shock and Fire Moisture Condensation WarningPlayable Discs About the DiscsExample Following discs cannot be played back on this DVD/VCRLights up when the power is on Press to turn the power on and offLights up when a cassette is in the DVD/VCR Operating Controls and Functions+100 button Press to accept a setting Press to reset the settingPress to select VCR mode for the remote control Press to select a desired audio language or sound modeDisplays During Operation DisplayLoading the Batteries Set to channel 3 or 4 to use your TV with your DVD/VCRSwitching to VCR Mode Switching to DVD Mode VCR/DVD SwitchingConnecting to a TV SwitchDVD/VCR to TV Connection If your TV does not have A/V terminalsFor TVs with Component Video in Jacks Dolby Digital DTS decoder To Select a Desired Channel Automatic Channel SET UPTo Preset the Channels Again To Change the ON-SCREEN Language Clock SET UPTo ADD/DELETE Channels ¡To go back one step, press the REW buttonNormal Playback Playback FunctionSearch Functions Auto Repeat PlaybackRecording Function Timer RecordingViewing and Recording Same Program Accidental Erasure PreventionTo Stop AN Automatic Timer PRO Hints for TimerTo CHECK, CORRECT, or Cancel AN Automatic Timer ProgramCopying a Video Tape Status will appear when you press StopTo Monitor the Recording Display button onPlaying a Disc Using the DVD MenusAuto Rewind Playing a DVD Video Or AN Audio CDPausing Playback or Displaying a Still Picture Using the Title MenuResuming Playback from Point Where Playback Stopped Stepping Through FramesSlow Motion Fast FORWARD/REVERSEStarting from a Desired Track Playing from a Desired Title or a ChapterMarker Starting from a Desired Time CountSet the marker Call back the markerYou can define a section to be played back repeatedly Repeat¡The starting point a will then be Repeat Selected ¡The selected section will be Played back repeatedlyTo Clear the Program Zoom PlaybackPlaying AN MP3 Disc When a Track is selectedWhen an Album is selected Playing AN MP3 Disc Randomly Playing a Desired Track From AN MP3 DiscPlaying AN MP3 Disc in a Program ¡The current audio status will appear at the top SettingsChanging the Audio Language or Sound Mode Changing the Camera Changing the Subtitle LanguageChanging the ON-SCREEN Display Black Level SettingsLanguage Settings Changing the Setup ItemsAuto Power OFF Default on Display SettingsWhen playing a disc with copyright protection Audio SettingsParental Lock All parental lock is cancelledLanguage Country code Language Code ListProblem Corrective Action Troubleshooting GuideDisc Handling Handling PrecautionsSpecifications Markham, Ontario Alden RoadL3R 4C1 Phone 905 FAX 905 0VMN03029 H9226CD
Top Page Image Contents