Magnavox MDV 530 VR owner manual Power Failure, VCR will not record a TV program, Poor reception

Page 76

76 Helpful Hints (cont’d)

Power Failure

VCR timer recordings, clock setting, language selection, and channel setup may be lost if the power fails. See pages 26-30 to set up the channels, clock, and language again. See pages 36-38 to reprogram your timer recordings.

The VCR will not record a TV program.

Put the DVD/VCR in VCR mode. Press VCR or OUTPUT so the green VCR light appears on the front of the DVD/VCR.

Check the connections between the DVD/VCR, TV, antenna/Cable TV signal, and Cable Box/Satellite Receiver (if applicable). Details are on pages 8-15. For VCR features, you must connect the DVD/VCR to a TV with the RF coaxial cable or the yellow video cable as described on pages 8-11.

Make sure the video cassette has a record tab. Details are on page 32.

The VCR will not perform a timer recording.

Make sure the recording start and stop times are set correctly. Details are on pages 36-38.

Make sure a tape is in the VCR and the tape has a record tab. Details are on page 32. If, after program- ming a timer recording, you press TIMER SET without putting a tape in the DVD/VCR, the TIMER REC light will blink.

If the record tab on a tape is missing, the DVD/VCR will eject the tape. The TIMER REC light will blink.

Press TIMER SET to put the DVD/VCR in standby mode for the timer recording. The TIMER REC light should appear on the front of the DVD/VCR.

Make sure the VCR clock is set. Details are on pages 28-29.

The VCR may not perform or continue a timer recording if the power fails.

If you have a Cable Box/Satellite Receiver, set timer recordings differently. Details are on page nine.

Finish programming a timer recording at least five minutes before it is set to begin.

12 p.m. is noon; 12 a.m. is midnight.

There is no picture or the picture is noisy or has streaks during video cassette playback.

Put the DVD/VCR in VCR mode. Press VCR or OUTPUT so the green VCR light appears on the front of the DVD/VCR.

If you used the supplied RF coaxial cable to connect the DVD/VCR to the TV, make sure the TV is on the same channel as the DVD/VCR’s output channel (03 or 04). The DVD/VCR’s output channel is chan- nel 3 when you receive it. To change it to channel 4, see page eight. Make sure channel 03 or 04 is prop- erly adjusted at the TV.

Or, if you connected the DVD/VCR to the TV using audio and video cables, select the correct Video In channel at the TV. Details are on pages 8-13.

Adjust the tracking. Details are on page 44.

TVs placed too close to the DVD/VCR can cause interference during tape playback. Move the DVD/VCR away from the TV.

The Number buttons won’t work for TV channels above 69.

Enter channel numbers as a two-digit number. If you want to select channels 100 and above, enter chan- nel numbers as a three-digit number. If you do not have Cable TV, only channels 2-69 are available.

TV programs cannot be watched normally.

Check the connections between the DVD/VCR, TV, antenna/Cable TV signal, and Cable Box/Satellite Receiver (if applicable). Details are on pages 8-15.

Poor reception

You may need to tune your TV again. Or, reset channels at the VCR using CHANNEL SET UP. Details are on pages 26-27.

Image 76
Contents MDV530VR For Customer Use Dear Magnavox product ownerModel No Serial No Safety Precautions Safety and General InformationDeclaration of Conformity Table of Contents Introduction Playable Discs and Video Cassettes Playable DiscsRegion Codes Color SystemsHookups Determining the best possible connectionBefore you begin RememberSignal Hookups cont’dConnections 2DVD/VCRRF coaxial cable Cable SignalChannel 03 or Video in Jacks On TV 2Audio Cables Video Cable DVD/VCR to a TV that has Component Video In jacks Antenna/Cable TV Signal DVD/VCR to a TV that has an S-Video In jack1Antenna/Cable TV Signal DVD/VCR to a TV and a StereoUsing Digital Audio connections Hookups cont’dRemote Control Setup Putting Batteries in the Remote ControlUsing the Remote Control Recycling Guidelines/Battery SafetyRepeat this process if the power fails First-time DVD/VCR SetupTurn on the TV Video Cassette Playback Other tape playback features are on pagesDetails are on pages Disc Playback Press OPEN/CLOSE aOn the DVD/VCR 4Insert a DiscDisplay Messages Display DVD Light redDisc tray STANDBY-ON LightTimer REC Light Display Panel VCRCounter/Clock/Channel Cassette CompartmentFront Panel AC Power Cord ANT-IN Antenna In Jack DVD Audio OUT JacksLeft white and Right red VCR Audio in JacksRemote Control Remote Control cont’d Channel Setup Press o or p to select Channel SET UP. Then, press BPress o or p to select Auto SET UP. Press B Now when you press Skip i/CHo or Skip jChannel Setup cont’d Adding/Deleting ChannelsClock VCR Follow these steps to set the VCR clock. Make sureWhile the DAY space is flashing, press o or p until Day appears. Then, press BClock VCR cont’d Press C-RESET/CLEAR to remove the menu Press o or p to select English Press C-RESET/CLEARLanguage VCR Press o or p to choose Language SELECT, then press BPress Display again to remove all the displays VCR Status DisplaysChannel numbers appear on Videotape Recording Recording PreventionRecording One Channel/Watching Another Select the channel you want to watch at the TVOne-Touch Recording Stopping an OTRPress Record on the DVD/VCR You cannot pause an OTRRerecording Tape Duplication Playing unitTo the TV’s Antenna in Jack Make the connections shown aboveTimer Recording Details are on page nine Timer Recording cont’dEnter the information while the space is flashing Cancelling Timer Recordings Press o or p to select a recording tape speed.DVD to Videotape Duplication Be possible only if the DVD is not copy protectedBefore you begin DVD Put the DVD you want to copy in the disc trayPress o or p to select Auto Repeat Repeat PlayPress B so on appears next to Auto Repeat Tape Counter Time Search Time Search, Index SearchIndex Search Special Effects Playback Forward and Reverse Searching SP/LP/SLPSuper High Speed Searching LP/SLP Viewing a Still PictureAutomatic Operation Features Multi-Channel Television Sound Understanding DisplaysMulti-Channel Television Sound cont’d Press DISC/MENU to remove the menuHi-Fi Stereo Press o or p to select Audio OUT Then, press BPress o or p to select HIFI. on will appear beside Please see additional notes onDVD Disc Menus Using the Title MenuPress TITLE. The Title menu will appear During playback, press FF g or REW h Fast Forward/Reverse SearchPress Play B to return to normal playback Press DVD to put the DVD/VCR in DVD mode Title/Chapter Playback, Specific Time PlaybackSpecific Title/Chapter Playback Specific Time PlaybackBA,B Track PlaybackPaused and Step-by-Step Playback, Resume Paused and Step-by-Step PlaybackResume Press DVDRepeat, A-B Repeat RepeatMarkers Subtitles Camera AnglesDuring playback, press Subtitle to select a subti During playback, press Angle to select a differentParental Controls Password Press SetupPower failure will not erase your password Press B to select CUSTOM, then press OKPassword Press DVD to put the DVD/VCR in DVD mode.Press the Number buttons to enter your four-digit Press o or p to select Parental LEVEL, thenAudio Language Stereo Sound ModeExample English audio Slow Motion DVD Slow Motion, ZoomZoom You cannot alter a Program dur- ing playback Programmed PlaybackProgram can have a maximum of 99 Tracks While playback is stopped, press Mode twice so Random PlaybackRed DVD light will appear Random screen appears62 MP3/JPEG Playback Or OKTo stop playback, press Stop C Jpeg Files have the iconOr, the following may appear to indicate Repeat play MP3/JPEG DisplaysPress Display again to remove the display When playback is stopped, press SETUP. Quick Setup screen will appearDisplay Press Or B to select display, then press OKPress Setup to remove the menus Display cont’dLanguage Language Codes Language cont’dPress o or p to select a language, then press While playback is stopped, press SETUP. AudioPress Display repeatedly to see the following dis On-Screen DisplaysPlays during DVD playback Press DVD to put the DVD/VCR in DVD mode Black Level, Virtual SurroundBlack Level Virtual SurroundCare and Maintenance Glossary Cable Box/DBS Output Channel 03 orSpecifications DVD/VCR has no power Remote control will not operate the DVD/VCRThere is no picture in DVD mode Helpful HintsHelpful Hints cont’d Power Failure VCR will not perform a timer recordingVCR will not record a TV program Number buttons won’t work for TV channels aboveLine Input mode Cleaning the Video HeadsYou cannot insert a video cassette You cannot remove the tapeLimited Warranty Magnavox, P.O. Box 520890, Miami, FL 33152 402Limited Warranty cont’d To obtain a replacement product from MagnavoxExchange Fee + Sales Tax = Total Payment, if applicableInformation Index Controls