JVC HR-XV48E Select the L-2 Select mode, Recording mode, Before performing the following steps

Page 29

Filename [XV48EX_EN_07S-VHS.fm]

 

 

Masterpage:Right-No-Heading

XV48EX_EN_01.book Page 29 Saturday, October 9, 2004 10:34 PM

EN 29

Before performing the following steps:

●Make sure the satellite receiver is connected to the unit’s L-2 IN/DECODER connector. ( pg. 50)

●Programme the timer on the satellite receiver.

●Insert a cassette with the safety tab in place.

●Slide the TV/VCR/DVD switch on the remote control to the right.

A Select the VHS deck.

On the unit

Press VCR/DVD repeatedly so that the VCR indicator lights up.

On the remote control

Press VCR so that the VCR indicator lights up.

B Select the L-2 SELECT mode.

Set “L-2 SELECT” to “A/V” or “SAT.” ( pg. 54)

●When you select “SAT”, refer to “IMPORTANT” on page 50.

C Set the tape speed.

Press p.

D Engage the Automatic Satellite Programme

Recording mode.

On the unit

Press and hold SAT# for about 2 seconds.

On the remote control Press and hold REC LINK for about 2 seconds.

●The “N” and “#” indicators light up and the unit turns off automatically.

NOTES:

●Operations on the DVD deck are not possible when the Automatic Satellite Programme Recording mode is engaged or timer recording is in progress.

●To disengage the Automatic Satellite Programme Recording mode, press REC LINK. The “N” indicator goes off.

●If the unit’s power is off, it is not possible to engage the Automatic Satellite Programme Recording mode.

●In step D, if the “N” indicator does not light but instead blinks quickly even though your satellite receiver’s power is off, Automatic Satellite Programme Recording will not work

properly with that satellite receiver*. If this is the case, perform “Express Timer Programming” ( pg. 26) to timer-record a satellite programme.

*Some satellite receivers output signals even if the power is off. Automatic Satellite Programme Recording is not possible with those satellite receivers.

●The “N” indicator blinks while Automatic Satellite Programme Recording is in progress.

●For timer programming of the satellite receiver, refer to the instruction manual of the satellite receiver.

●Automatic Satellite Programme Recording is not possible if your satellite receiver does not have a timer.

●Pressing the unit’s 1 button while Automatic Satellite Programme Recording is in progress turns off the unit’s power and disengages the Automatic Satellite Programme Recording mode.

●If there are more than one satellite programmes you wish to record with Automatic Satellite Programme Recording, it is not possible to set different tape speeds for each programme.

●Depending on the type of satellite receiver, the unit may not record a slight portion of the beginning of the programme or may record slightly longer than the actual length of the programme.

●If you engage the Automatic Satellite Programme Recording mode when the satellite receiver’s power is on, the unit will not start Automatic Satellite Programme Recording even though the “N” and “#” indicators blink. When the satellite receiver shuts off once and is turned back on again, the unit starts recording.

●You can also record a programme from your cable system in the same way if the system has a timer.

●The B.E.S.T. system ( pg. 23) does not work while Automatic Satellite Programme Recording is in progress.

●Just Clock ( pg. 65) does not work when the Automatic Satellite Programme Recording mode is engaged.

Page 29

October 9, 2004 10:34 pm

Page 28 Page 30
Image 29
Page 28 Page 30
Contents HR-XV48E Filename XV48EXEN03Safety.fm Safety PrecautionsUse only discs marked with the following Mains outletContents Playable Discs About DiscsUnplayable Discs Region NumberPlacing a Disc File Structure of DiscsCare and Handling of Discs Rear View Front View pg , 50 Filename XV48EXEN06Index.fmTape Remaining Time Indicator  pg Automatic Satellite Programme Recording IndicatorFront Display Panel On-Screen Display VHS deckHow To Use Remote ControlBasic Connections Check the contentsSituate the unit Connect the unit to TV10 EN Auto Set UpTurn on the unit Select your countryConfirm/Set video channel Perform Auto Set UpEnter or e With RF ConnectionSet the video channel Perform Preset Download12 EN Link Functions Results of Auto Set Up/PresetPanel 14 EN Select the modePress VCR so that the VCR indicator lights up Access the Country Set screenLanguage Select the VHS deckDVD deck only Select the mode16 EN Language Code List Load a cassette 18 ENPlayback Features Manual Tracking 20 ENSoundtrack Selection Instant ReViewBasic Recording Instant Timer Recording ITR Recording Features22 EN Elapsed Recording Time IndicationReceiving Stereo and Bilingual Programmes S.T. Picture SystemPlayback RecordingProgramming Howv IEW TM Timer24 EN VPS/PDC signal Engage the unit’s timer modeVPS/PDC Recording Satellite Receiver Users26 EN Express TimerDisengage the timer mode To cancel or change a programmeAccess the Programme Check screen Cancel or change a programmeCancel or change programme setting When Programmes Overlap Each Other28 EN Select the programme to modifyRecording mode Select the L-2 Select modeBefore performing the following steps Set L-2 Select to A/V or SAT.  pgPause playback 30 ENLoad the disc Access the DVD menu Locating a Desired Scene Using the DVD MenuAccess the PBC menu Locating the Start Point of the Item or Skip the ItemStill Picture/Frame-By-Frame 32 ENZooming PressSelect the repeat mode Access the repeat modeAccess the on-screen bar Repeat Playback34 EN Access the menuTime Search Operations on DVD DeckSelect the audio language Angle SelectionSelect the view angle Random Playback 36 ENProgramme Playback Sound Effect VFP Function Adjusting the Picture QualityAccess the menu bar How to Access the On-Screen BarAccess the status bar 38 ENMenu Bar Functions for SVCD/Video CD/Audio CD Audio/Video Files 40 ENPlayback Basic OperationsSelect the random playback mode Change the playback modeLoad the disc Select a groupChanging the Picture of the Opening Display 42 ENSlide Show Playback Jpeg Files Select a DivX file Select a subtitle fileAssociated subtitle files ScreenMake connections 44 ENMake connections Engage the Record Pause mode of the recording deckStart the source player Start the recording deckStart dubbing 46 ENEnd dubbing Load a cassette and place a discPrepare the DVD deck for dubbing Place a disc and load an MDPrepare the audio device for dubbing For the digital audio device48 EN Set the TV brand code Press TV 1 on the unit’s remote control to turn onOperate the TV Keep pressing VCR down during step aPerfect Connections 50 ENReceiver DTS DVD deck only Select the input modeMake connections Connect the decoderAccess the Main Menu screen Mode Set VHS deckAccess the Mode Set screen 52 ENFor Example LP modeWhen you use the Direct Rec function, be sure to use a TV About Ntsc Playback 54 ENFor each mode setting, see corresponding pages Mode Set DVD deckPress rt to move H to RESUME, then press Enter Press rt to select ON, then press EnterPicture Settings Subsidiary SettingsAudio Settings 56 ENPlayback discs Output Others SettingsParental Lock 58 EN Country/Area Code List for Parental LockAuto Channel Set Tuner SetPerform Auto Channel Set View the Confirmation screenManual Channel Set 60 ENDeleting a Channel When Receiving a Scrambled Broadcast62 EN Setting Station Names ManuallyFine-Tuning a Stored Channel Station Name TV Station and ID ListExit the Video Channel Set mode Access the Video Channel Set mode64 EN Set the video channelClock Set Set the Child Lock 66 ENTape Transport VHS deck PowerPlayback VHS deck Playback DVD deckAudio/Video Files Playback DVD deck 68 ENRecording VHS deck Scene is not recorded from multiple anglesOther Problems Timer Recording VHS deck70 EN Connecting/Using a Decoder Auto Channel Set Auto Set UpExpress Timer Programming Fine-Tuning a Stored Channel Remote Control Functions Repeat PlaybackFilename XV48EXEN13Cov4.fm
Top Page Image Contents