JVC HR-XV1EU manual SHOWVIEW-Recording, Setting a day of the week, Change the recording start-time

SHOWVIEW®-Recording

Example: You receive NBC on program position 12.

In case of the first SHOWVIEW-recording for NBC, 2 bars will blink at the CH-line. Enter 12 with number keys. Press 1 and then 2 within 2 seconds (if the 2-press was too late, the display 1 will be replaced with 2). The SHOWVIEW-system memorizes that the storing position 12 is for NBC. From the next all times of the SHOWVIEW-

VPS/PDC:

Switch the VPS/PDC on or off. Be sure to pay attention to the VPS/PDC-important note on page 35.

Press or repeatedly until you reach VPS/PDC- line.

Then press or to select “ON” or “OFF”.

recording from NBC, the 12 will be entered in the “CH”- line automatically. In case of an erroneous input for the

channel number, press	to go in the “CH”-line and
enter the correct number again.
Press / or number	SHOWVIEW NO . 327741029
keys to enter the program	DATE	15 TUE
	START	17:30
position number.	END	18:00
Then press .	CH	12 NBC
	SPEED	SP
	VPS/PDC	OFF

5 Press OK after the confirmation. Then press SET UP MENU repeatedly until the TV- picture appears.

To enter the other program repeat the steps 1 - 5.

15 TUE	17:30	18:00	7V SP
------	--:--	--:--	--	-
------	--:--	--:--	--	-
------	--:--	--:--	--	-
------	--:--	--:--	--	-
------	--:--	--:--	--	-
------	--:--	--:--	--	-
------	--:--	--:--	--	-
SELECT :		/ OK
EXIT	: MENU

SELECT :
SET	:	/ 0–9
EXIT	: MENU OK : OK

Setting a day of the week:

You have selected DAILY or WEEKLY in step 3, then you can select recording date again.The date must blink as 2 bars.

If it does not blink, then press or repeatedly until the DATE blinks. Then press or repeatedly until the desired date appears.

The following date are stand for your selection: SUN-

SAT: all dates from Sunday to Saturday, or MON-SAT:

only dates from Monday to Saturday, or MON-FRI: only

dates from Monday to Fryday. WKL-MON: each Monday,

WKL-TUE: each Tuesday, ..., WKL-SUN: each Sunday.

Change the recording start-time:

The recording start-time will be set by SHOWVIEW automatically. However you can change the recording start-time manually. The time near START must blink.

If it does not blink, press or repeatedly until the time blinks. Then press to change.

Recording period extension:

The recording end-time will be set by SHOWVIEW automatically. However you can extend the recording end-time manually. The time near END must blink.

If it does not blink, press or repeatedly until the time blinks. Then press to extend.

Select Tape speed:

Select the recording tape speed Standard Play (SP) or Long Play (LP).

Press or repeatedly until you are in SPEED-line. Then press or to select “SP” or “LP”.

6 Press •. The clock symbol ( ) will appear on the display and the VCR stands by for recording. At the same time, VCR mode will change to DVD mode automatically. You can use DVD even if the VCR is in the Timer recording mode.

If you do not use the DVD, turn the power off.

The timer recording will start at 5 seconds before the time you predetermined.

Note:

•If the clock symbol ( ) does not appear on the display in spite of the pressing of •, the cassette may not have been loaded yet.(see page 22)

•If the cassette is ejected in spite of the pressing of •, the erase prevention tab of the cassette may have been removed. (see page 22)

•If the clock symbol ( ) blinks when the timer re- cording ended, the TV program has not been com- pletely recorded because of an insufficient tape sup- ply. In this case, press • to cancel the timer pro- gram or press EJECT to remove the cassette tape.

•During timer recording standby mode, the VCR mode cannot be selected. To use the VCR, press

•at first, then press VCR to change to VCR mode. After you use the VCR, press • again to put the VCR into timer recording standby mode.

•If you press • during timer recording, the record- ing operation will be interrupted. If you press • again within the programmed time, the recording operation will start again.

32