3M 39600 manual Emergency Stop Switch, Tape Loading/Threading

Page 19

Operation (Continued)

WARNINGS

1.Turn electrical supply off and disconnect before servicing taping heads or performing any adjustments or maintenance on the machine.

2.Do not leave machine running unattended.

3.Before turning drive belts on, be sure no tools or other objects are on the machine bed.

4.Keep hands and loose clothing away from moving belts.

5.Keep hands and clothing away from taping heads when machine is running. A box traveling through the machine causes taping head rollers to retract when box enters and extend as box leaves taping head.

6.Never attempt to work on any part of the machine, load tape or remove jammed boxes from the machine while machine is running.

7.When feeding boxes to the machine by hand, push box in from end only – DO NOT PUSH WITH HANDS ON ANY CORNER OF THE BOX.

8.Both the upper and lower taping heads utilize extremely sharp knife blades. The blades are located under the orange blade guard which has the 'WARNING – SHARP KNIFE" label. Before loading tape, refer to Figures 3-1 and 3-2 in Section II to identify the blade location. Keep hands out of these areas except as necessary to service the taping heads.

9.Turn drive belts "Off" when machine is not in use.

10.Failure to comply with these warnings could result in severe personal injury and/or equipment damage.

Electrical "On/Off" Switch

The box drive belts are turned on and off ("Off" button is red) with the electrical switch on the side of the machine frame.

Note –The case sealer has a circuit breaker located in the electrical enclosure on the lower left side of the machine frame. If circuit becomes overloaded and circuit breaker trips, unplug the machine electrical cord and determine cause of overload. After two minutes, open the electrical enclosure and reset the circuit breaker by lifting the reset lever. Close the electrical enclosure, plug machine electrical cord into outlet and restart machine by pressing "I" (On) button.

Emergency Stop Switch

The machine electrical supply can be turned off by pressing the latching emergency stop switch. To restart machine, rotate emergency stop switch (releases switch latch) and then restart machine by pressing "I" (On) button on side of machine frame.

Tape Loading/Threading

See Section II, Pages 7 and 8

Note –If lower tape drum is mounted in alternate lower outboard position, remove taping head from machine bed by pulling straight up, insert threading needle in taping head and replace taping head. Install tape roll on drum (adhesive on tape leg up), thread tape under knurled roller on outboard mount, then attach tape to threading needle and pull tape through taping head with threading needle.

CAUTION – Taping head weighs approximately 7.2 kg [16 pounds]

without tape. Use proper body mechanics when removing or installing taping head.

14

Page 18 Page 20
Image 19
Page 18 Page 20
Contents 3M-Matic To Our Customers Replacement Parts and Additional ManualsTo Our Customers Table of Contents Section II AccuGlide II STD 2 Inch Taping Heads Description Contents 700a Adjustable Case Sealer Knife Warning Label Important SafeguardsPinch Point Caution Label Safety Instructions label, shown Center Box Label Specifications Tape Application Leg Length Optional Box Weight and Size CapacitiesTape Roll Diameter Tape Application Leg Length StandardSet-Up Recommendations Machine Dimensions MinimumReceiving And Handling Installation and Set-UpUncrated 700a Frame Set-UpMachine BED Height BOX Size Capacity of Case Sealer 700a Case Sealer Components Left Front View OperationTape Loading/Threading Emergency Stop SwitchUpper Taping Head Box Size Set-UpWill occur Check AdjustmentsBox Sealing Lubrication MaintenanceLower Drive Belt Replacement Could result Box Drive Belt ReplacementCould result Circuit Breaker Blade Replacement, Taping HeadCould result Box Drive Belt Tension AdjustmentsCould result Box Drive Belt Tension Adjustment, Lower BeltsInfeed EndPersonnel could result This page is Blank Case Sealer Frame Changes Special Set-Up ProcedureRemove Upper Taping Head To personnel could resultBox and Machine Bed Height Range Box and Machine Bed Height Range -Refer to FigureTroubleshooting Guide Problem Cause Correction TroubleshootingElectrical Diagram Electrical DiagramThis page is Blank Replacement Parts And Service Information Part Number Option/Accessory Options/AccessoriesReplacement Parts Illustrations and Parts Lists This page is Blank 700a Adjustable Case Sealer Frame Assemblies 700a Adjustable Case Sealer Ref. No 3M Part No Description 700a Adjustable Case Sealer Ref. No 3M Part No Description 700a Adjustable Case Sealer Ref. No 3M Part No Description 700a Adjustable Case Sealer Ref. No 3M Part No Description 700a Adjustable Case Sealer Ref. No 3M Part No Description 700a Adjustable Case Sealer Ref. No 3M Part No Description 700a Adjustable Case Sealer Ref. No 3M Part No Description 700a Adjustable Case Sealer Ref. No 3M Part No Description 700a Adjustable Case Sealer Ref. No 3M Part No Description 700a Adjustable Case Sealer Ref. No 3M Part No Description 700a Adjustable Case Sealer Ref. No 3M Part No Description Safety and Information Labels Ref. No 3M Part No Description Qty Safety and Information Labels
Related manuals
Manual 72 pages 62.27 Kb Manual 94 pages 44.17 Kb Manual 70 pages 21.44 Kb Manual 70 pages 16.15 Kb

39600 specifications

The 3M 39600 is a high-quality, versatile adhesive designed to meet the needs of professionals across various industries. This product is particularly well-regarded for its exceptional bonding capabilities and ease of use, making it a popular choice among contractors, automotive professionals, and DIY enthusiasts alike.

One of the main features of the 3M 39600 is its strong adhesion to a wide range of substrates. This includes metals, plastics, glass, and composites, allowing users to bond different materials seamlessly. The adhesive forms a strong, durable bond that provides long-lasting performance, making it suitable for both interior and exterior applications.

Another key characteristic of the 3M 39600 is its fast curing time. The adhesive typically sets quickly, which is crucial in fast-paced work environments where time is of the essence. This rapid curing allows users to proceed with their projects without long wait times. Additionally, the adhesive exhibits high resistance to moisture and temperature fluctuations, ensuring that the bond remains secure even in challenging environmental conditions.

The technology behind the 3M 39600 is based on advanced polymer chemistry, which contributes to its reliable performance. The formulation of the adhesive results in excellent shear strength and tensile strength, making it ideal for demanding applications. The product is also designed to be user-friendly; it can be applied using various methods such as brush, roller, or spray, depending on the specific requirements of the project.

3M 39600 is often recognized for its versatility. It is suitable for applications in industries like automotive, construction, electronics, and appliance manufacturing. In the automotive sector, for example, it is used for bonding parts together, ensuring structural integrity and enhancing both performance and aesthetics.

In summary, the 3M 39600 adhesive is a top choice for those seeking a reliable and efficient bonding solution. Its strong adhesion, fast curing time, and advanced technology make it suitable for a variety of applications. Whether you are a professional or a DIY enthusiast, the 3M 39600 provides the performance you need to achieve quality results in your projects.
Top Page Image Contents