Daewoo DF-8100P, DF-4100P Amplifier. Use an optional digital coaxial audio cable, Connecting a TV

Page 10

Connections

Connections

 

 

Connecting a TV

Choose one of the following TV connections, depending on the capabilities of your equipment.

All video signals are available from all video outputs. That means that whichever TV connection you use, it will

work with all input sources, including VHS out of the Component/Progressive Video Output.

Connecting an Amplifier/Receiver

Connecting to an amplifier equipped with two channel analog stereo or Dolby Pro Logic ll/Pro Logic

Connect the Left and Right AUDIO OUT jacks on the DVD Recorder+VCR to the left and right audio in jacks on your amplifier, receiver, or stereo system, using the supplied audio cables (A).

RF Connection

Connect the RF OUT (TO TV) jack on the DVD Recorder+VCR to the antenna in jack on your TV using the supplied 75-ohm RF cable (R).

Scart Connection

1Plug a scart cable into the scart socket EURO AV1 at the back of the DVD Recorder+VCR and the corresponding scart socket at the back of the TV set. (V)

2Plug a scart cable into the blue scart socket EURO AV2/DECODER at the back of the DVD Recorder+VCR and the corresponding scart socket at the back of the Decoder.

Rear of TV

 

S-VIDEO

COMPONENT/PROGRESSIVE VIDEO INPUT

ANTENNA

 

INPUT

 

 

 

INPUT

 

 

Pr

Pb

Y

 

S

 

C

 

V

R

Connecting to an amplifier equipped with two channel digital stereo (PCM) or to an Audio/Video receiver equipped

 

with a multi-channel decoder (Dolby Digital™, MPEG 2, or DTS)

CONNECTIONS

1

Connect the DVD Recorder+VCR’s DIGITAL AUDIO OUT jack (Coaxial) to the corresponding in jack on your

 

amplifier. Use an optional digital coaxial audio cable. (X)

2 You will need to activate the DVD Recorder+VCR’s digital output; see ‘Audio’ Settings on page 28.

Digital Multi-Channel Sound?

A digital multi-channel connection provides the best sound quality. For this you need a multi-channel audio/video receiver that supports one or more of the audio formats supported by your DVD Recorder+VCR (MPEG 2, Dolby Digital, and DTS). Check the receiver manual and the logos on the front of the receiver.

• Due to the DTS Licensing agreement, the digital output will be in DTS digital out when DTS audio stream is

selected.

• If the audio format of the digital output does not match the capabilities of your receiver, the receiver will produce

a strong, distorted sound or no sound at all.

• 5.1 channel digital surround sound via the digital connection can only be obtained if your receiver is equipped with

a digital multi-channel decoder.

S-Video Connection

Rear of DVD Recorder+VCR

1Connect the S-VIDEO OUT jack on the DVD Recorder+VCR to the S-Video in jack on your TV using an S- Video cable (S).

2Connect the Left and Right AUDIO OUT jacks from the DVD Recorder+VCR to the left/right audio in jacks on your TV using the audio cables.

Component Video Connection

1Connect the COMPONENT/PROGRESSIVE VIDEO OUT jacks on the DVD Recorder+VCR to the corresponding in jacks on your TV using a Y Pb Pr cable (C) if the component (Y, Pb, Pr) is available on your TV.

2Connect the Left and Right AUDIO OUT jacks from the DVD Recorder+VCR to the left/right audio in jacks on your TV using the audio cables.

Progressive Scan Connection

•If your television is a high-definition or ‘digital ready‘ television, you may take advantage of the DVD Recorder+VCR’s Progressive Scan output for the highest video resolution possible.

•If your TV does not accept the Progressive Scan format, the picture will appear scrambled.

1Connect the COMPONENT/PROGRESSIVE VIDEO OUT jacks on the DVD Recorder+VCR to the corresponding in jacks on your TV using an optional Y Pb Pr cable (C).

2Connect the Left and Right AUDIO OUT jacks from the DVD Recorder+VCR to the left/right audio in jacks on your TV using the audio cables.

•Be sure to set the DVD Recorder+VCR to Progressive Scan mode by pressing and holding [P.SCAN] for 3 seconds (or changing the ‘Video Output’ in the Setup Menu; see page 27).

•Progressive Scan does not work with the RF, Audio/Video or S-Video connections.

• To see the audio format of the current DVD on the on-screen display, press [AUDIO].

The DVD Recorder+VCR does not perform internal (2- channel) decoding of DTS sound tracks. To enjoy DTS multi- channel surround, you must connect the DVD Recorder+VCR to a DTS compatible receiver via one of the DVD Recorder+VCR’s digital audio outputs.

Rear of DVD Recorder+VCR

A X

 

 

 

 

 

L

R

COAXIAL

AUDIO INPUT

DIGITAL INPUT

 

 

 

 

Amplifier (Receiver)

16

 

 

 

17

 

 

Page 9 Page 11
Image 10
Page 9 Page 11
Contents DVD Recorder + VCR 97P95600D0-1VPrecautions Safetyty InstructionsI t tiAlcohol- based cleaning agents For your own SafetyAvoid direct exposure to beam Important SafeguardsUnit leave all servicing to qualified service personnel All operating and use instructions should be followedTable of Contents Number of this player, the disc cannot be played OverviewiFollowing discs can be used in your DVD Recorder+VCR About Symbols To keep the surface cleanPrecautions After playing, store the disc in its caseIdentification of Controls Details, Refer to One Touch Record OTR on Remote ControlTurns the DVD Recorder+VCR on and off Copies from DVD to VCR or from VCR to DVDConnect to a TV with an RF coaxial input If your cable wire is connected to your TV without aConnectionsti Connect to a TV with an S-Video InputConnecting an Amplifier/Receiver Connecting a TVAmplifier. Use an optional digital coaxial audio cable Initial Installation Initial InstallationConnecting Optional Equipment DV Digital CamcorderCable If you are using basic cable to receive channels Initial SetupPress Setup to exit the Setup menu After finishing Auto Channel Search, set the clockAuto Set Set ClockSet Clock Use œ and √ to select ‘Language‘ Follow the same procedure as the ‘DVD Record Quality’Press SETUP. The Setup menu appears Press Enter to move to the second levelFlickering Press Setup Use œ/√ to select ‘Preferences‘Press ENTER. The ‘Video‘ submenu is displayed Scart jacks, set Video Output to ‘RGB’Displayed No signal will be output from the Digital Audio Out jacksEnter your new password Use …/† to select the desired digital output typePress Enter to display the submenu PasswordAuto Settings Press ENTER. The ‘Parental Controls‘ submenu appearsOn-Screen Displayi l Overviewverview OSD Menu Options for DVD Use …† to change the numbers Press Enter to confirmFunction does not work Playing a DVD DVD PlaybackSlow reverse playback is not supported Œ3 1 √ † VCR PlaybacklIt will be automatically selected by the DVD Recorder+VCR To return to normal playback, press Play Special Playback FeaturesOthert Disci Playbackl DVD Recorder+VCR can display Jpeg files on CD-R/RWMake sure your TV input is set to view the DVD Recorder+VCR Basicic RecordingiFollow the instructions below to record a TV program Playing MP3 Files During a Slide ShowSP Standard Play LP Long Play, 2 times SP During one touch copy you can search and resume copy Insert the VHS videotape you wish to copy into the VCR deckTape ends One Touch Copy VHS to DVDStopping a Timer Recording in Progress When the earlier program finishes, the later program startsCanceling a Timer Recording Timer Recording TroubleshootingDV appears on the front panel display and the TV screen Recording from an External InputRecording from External Components Editing Change Disc Name Title MenuYou can erase titles on DVD+RW discs only Play a TitleSP Add a space Character or function and press EnterCLR Clear the whole title Save Save the title nameTurn on the TV TroubleshootingClean the video heads Audio cables are not connected securelyTechnicali l Specificationsi i ions Audio output DVD Video output terminal, 1.0 Vp-p, unbalancedVideo output DVD Video output YYour 1ST Year MANUFACTURER’S Guarantee Daewoo Guarantee Department
Top Page Image Contents